DDT

DDT (Dynamic Debugging Technique - the name is a 'backronym' on the insecticide) is a family of debuggers with some common characteristics:

• Most commands are invoked with a single key, plus modifiers.
• Altmode or Escape is used as a prefix modifier.
• Arguments are commonly prefixed to the command.

DDT was first implemented at MIT for a PDP-1 computer. It was then implemented for PDP-6, -10, and -11 computers at MIT. It was also widely used at DEC.

Implementations

Implementations found on ITS

• Exec DDT, also known as NTS DDT, for the PDP-6 and 10.
• Timesharing DDT for the PDP-6 and 10.
• KLDDT specifically for the KL10.
• RUG for the PDP-11.
• URUG, or micro RUG, for the GT40.
• KLRUG for the KL10 front end.
• 11DDT for the PDP-11.
• CARPET remote PDP-11 debugger hosted on a PDP-10.
• HALI target resident counterpart to CARPET.
• MAT resident debugger for PDP-11.
• Timesharing DDT for SITS.
• IMDDT for Imlac PDS-1.

DEC implementations

• ODT

Implementations under MOS

The original debugger used with the MOS operating system was a DDT written in PDP-11 assembly language (like the OS itself); it is not known if that was written from scratch, or came from elsewhere.

Later, a version was written in portable C, and used with MOS (similarly re-written) the on PDP-11's, various Motorola M68000 Family machines, and AMD 29000 machines.

Command list for the MOS portable DDT

In the list below, '$' means the ASCII character 'ESCAPE' (i.e. CTRT-[). This command set was derived from, but not identical to, those of the originals.

           n/     Open loc n, type contents in current mode
           /      Retype loc pointed to by last address
           n<CR>  Modify currently opened loc to be n, close loc
           <CR>   Reset modes, go to command level
           n<LF>  Modify, close, open next loc
           <LF>   Advance to next item and display
           n^     Modify, close, open previous loc
           ^      Reverse to previous item
           n<TAB> Modify, close, open loc pointed to by last typed value
           <TAB>  Open loc pointed to by last typed value
           @      Synonym for <TAB>
           n_     Open location n, type as instr
           _      Set temporary mode to instr, retype location
           n{     Open location n, type as a numeric
           {      Set temporary mode to numeric, retype location
           n[     Open location n, type as symbolic
           [      Set temporary mode to symbolic, retype location
           n!     Open location n, don't type
           n=     Type value as numeric
           =      Retype value as numeric
           n\     Examine display block at n
           \      Examine display block pointed to by last address

            $A    Addresses will be typed as absolute numbers
            $R    Addresses will be typed relative to symbols
            $I    Change current mode to instruction type out
            $N    Change current mode to numeric type out
            $S    Change current mode to symbolic type out
            $T    Change current mode to ASCII text output
            $Z    Change current mode/length to .ASCIZ
            $H    Change to halfword (byte) mode
            $W    Change to (short)word mode
            $L    Change to longword mode
            $mI   Change current input radix to m
            $mO   Change current output radix to m
            $mR   Change input and output radix
            $mD   Change current display block size
                  Note that the initial modes are $S and $W. These
                  can be temporarily changed by the above commands and
                  will return to the permanent setting by a carriage
                  return.  The settings can be permanently changed by
                  using two altmodes in the mode setting command
                  (e.g. $$T sets permanent ASCII mode)

            $mS   Change maximum symbol offset
                  This mode is 'permanent' i.e. once set, it
                  stays at that value.

            n$iM  Set machine dependant mode i to n.
                  The actual argument syntax may vary from machine to
                  machine.

            n$iB  Set breakpoint i at address n (i from 0 to 7 or can
                  be omitted)
            $iB   Remove breakpoint i
            $B    Remove all breakpoints
            $V    List (view) all breakpoints
                  Note that breakpoints should only be set at the start
                  of extended instructions. Setting a breakpoint in the
                  middle of an instruction will cause undefined randomness.

%           $P    Proceed from breakpoint
%           m$P   Proceed from breakpoint m times (without halting)
%           ^P    Single step the processor
%           n^P   Single step n times (without halting)
%           ^X    'Execute' step the processor - treats JSR as an atomic
%           n^X   Execute step n times (without halting)
%           $G    Start execution at address in JOBSA (start of program)
%           n$G   Start executing program at location n.


Commands marked with a '%' can be executed only in the hard-core
debugger with the [operating system] halted.

Numbers 'm' may be typed either before or after the '$'; numbers 'n'
or 'i' must be typed where shown.

Where a value is called for, if the value is typed before the
'$' (if any), the value may be typed as a string of tokens, which may
be either numbers or known symbols (i.e. findable in the DDT symbol
table) separated by operators; the available operators are +, - and *.
If the value is typed after the '$' only a single number may be used;
these are read in decimal unless preceeded by a 0.