Difference between revisions of "BA11-N mounting box"

From Computer History Wiki
Jump to: navigation, search
(Add info, copyedit)
m (New cat)
 
(11 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
The '''BA11-N mounting box''' was the a [[mounting box]] used for [[QBUS]] [[PDP-11]]'s from [[Digital Equipment Corporation|DEC]]. It included an [[H786 power supply]], and an [[H9273 backplane|H9273-A]] 9-slot [[QBUS#Backplanes|Q/CD]] [[backplane]], which could hold [[DEC card form factor|quad-sized]] cards.
  
The '''BA11-N mounting box''' was the a [[mounting box]] used for [[QBUS]] [[PDP-11]]'s from [[Digital Equipment Corporation|DEC]]. It included an H786 [[power supply]] (which provided 22A of +5V, and 11A of +12V, although some sources say 15A and 8A respectively); and an H9273-A 9-slot [[QBUS#Backplane|Q/CD]] [[backplane]], which could hold [[DEC card form factor|quad-sized]] cards.
+
The manual says the BA11-N was for [[PDP-11/03L]]'s, but the [[LSI-11]] used in that machine was only [[QBUS#Variable_address_size|Q16]] capable, making the Q18 H9273 backplane superfluous, like that in the [[BA11-M mounting box]]. Once the [[PDP-11/23]] appeared, BA11-N's could be used with it (and perhaps the BA11-N was looking forward to this machine) - but after the -A revision of the /23's [[KDF11-A CPU]] (Q18 only), later revisions really were better off with a Q22 backplane, as in the up-rated [[BA11-S mounting box]].
  
The H9273-A was a [[QBUS#Variable_address_size|Q18]] backplane, but it is relatively easy to [[upgrading QBUS backplanes|upgrade it to Q22]].
+
Since the H9273 was a Q/[[CD interconnect|CD]] backplane, dual-width [[QBUS]] cards could only be placed in the left-hand slots, and quad QBUS-only cards had to not use any pins on the [[DEC edge connector contact identification|right-hand C/D connectors]]. (The only DEC card with a problem with this seems to have been the [[MMV11-A QBUS core memory|MMV11-A]].)
  
The manual says the BA11-N was for [[PDP-11/03L]]'s, but this seems odd, since the [[LSI-11]] used in that machine was only Q16 capable, making the Q18 backplane superfluous. Once the [[PDP-11/23]] appeared, BA11-N's could be used with it (and perhaps the BA11-N was looking forward to this machine) - but after the A revision of the /23's [[KDF11-A CPU]] (Q18 only), later revisions really were better off with a Q22 backplane.
+
It was available both with a front panel with a bezel (with '[[bootstrap|Boot]]', '[[Halt]]' and '[[LTC]] On' switches, and power and run status indicators); and also with a blank front panel (for use as an expansion box).
  
Since it was a Q/[[CD interconnect|CD]] backplane, dual-width [[QBUS]] cards could only be placed in the left-hand slots, and quad QBUS-only cards had to not use any pins on the [[DEC edge connector contact identification|right-hand C/D connectors]]. (The only DEC card with this limitation seems to have been the [[MMV11-A]].)
+
It was a 5-1/4" tall mounting box, for the [[H960 rack|H960]] series of 19"-wide racks, one of the [[BA11 mounting boxes]]. The H960 racks provided 63" of vertical mounting space, divided into units of 10-1/2", which were further subdividable into a pair of 5-1/4" spaces. The 5-1/4" tall BA11-N mounting box was designed for these spaces.
  
It was available both with a front panel with a bezel (with '[[Bootstrap|Boot]]', '[[Halt]]' and '[[LTC]] On' switches, and power and run status indicators); and also with a blank front panel (for use as an expansion box).
+
For rack mounting purposes. it did not use external slides (as all the other BA11 mounting boxes did); instead, it was housed in an external 'skin' (termed a 'logic box cover' in DEC documentation, the base unit being called a 'logic box') into which it is slid; the cover would be bolted to the rack.
  
It was a 5-1/4" tall mounting box, for the [[H960 rack|H960]] series of 19"-wide racks, one of the [[BA11 mounting boxes]]. The H960 racks provided 63" of vertical mounting space, divided into units of 10-1/2", which were further subdividable into a pair of 5-1/4" spaces. The 5-1/4" tall BA11-N mounting box was designed for these spaces.
+
The backplane was mounted vertically, facing backward (unlike the BA11-M mounting box, where they had been facing forward). Cooling fans mounted on the side of the BA11-N passed air both over the boards, and through the power supply.
 +
 
 +
The BA11-N's dimensions were 5-1/4" high, 19" wide, and 22-3/4" deep, and it weighed 44 lbs (without any boards). The rack mounting was 26-3/4" long.
 +
 
 +
{{semi-stub}}
 +
 
 +
==See also==
 +
 
 +
* [[BA11-M mounting box]]
 +
* [[BA11-S mounting box]]
 +
 
 +
==Further reading==
  
For rack mounting purposes. it did not use external slides (as all the other BA11 mounting boxes did); instead, it was housed in an external 'skin' *termed a 'logic box cover' in DEC documentation, the base unit being called a 'logic box') into which it is slid; the cover would be bolted to the rack.
+
* ''BA11-N Mounting Box Technical Manual'' (EK-BA11N-TM-001) - not available online
 +
* ''BA11-N Mounting Box Illustrated Parts Breakdown'' (EK-BA11N-IP) - not available online
  
The backplane was mounted vertically, facing backward (unlike the [[BA11-M mounting box]], where they had been facing forward). Cooling fans mounted on the side of the BA11-N passed air both over the boards, and through the power supply.
+
==External links==
  
The BA11-N's dimensions were 5-1/4" high, 19" wide, and 22-3/4" deep, and it weighed 44 lbs (without any boards). The rack mounting was 26-3/4" long.
+
* [http://www.bitsavers.org/pdf/dec/qbus/Digital_Microcomputer_Interfaces_Handbook_1980.pdf microcomputer interfaces handbook] - BA11-N is covered on pp. 74-82, 82-90 of the PDF
 +
* [http://www.bitsavers.org/pdf/dec/qbus/Digital_Microcomputer_Products_Handbook_1985.pdf Microcomputer Products Handbook] - the BA11-M is covered in Chapter 54 (pp. 523-527 of the PDF)
 +
* [http://www.bitsavers.org/pdf/dec/qbus/EK-BA11N-UG-001_BA11-N_Mounting_Box_Users_Guide_Jan78.pdf BA11-N mounting box user's guide] (EK-BA11N-UG-001)
 +
* [http://www.bitsavers.org/pdf/dec/qbus/MP00740_1123_schem_Oct81.pdf PDP11/23 Field Maintenance Print Set] (MP00740) - Contains the BA11-N Field Maintenance Print Set (MP00487) on pp. 32-87)
  
{{PDP-11}}
+
[[Category: DEC Mounting Boxes]]

Latest revision as of 02:22, 11 July 2023

The BA11-N mounting box was the a mounting box used for QBUS PDP-11's from DEC. It included an H786 power supply, and an H9273-A 9-slot Q/CD backplane, which could hold quad-sized cards.

The manual says the BA11-N was for PDP-11/03L's, but the LSI-11 used in that machine was only Q16 capable, making the Q18 H9273 backplane superfluous, like that in the BA11-M mounting box. Once the PDP-11/23 appeared, BA11-N's could be used with it (and perhaps the BA11-N was looking forward to this machine) - but after the -A revision of the /23's KDF11-A CPU (Q18 only), later revisions really were better off with a Q22 backplane, as in the up-rated BA11-S mounting box.

Since the H9273 was a Q/CD backplane, dual-width QBUS cards could only be placed in the left-hand slots, and quad QBUS-only cards had to not use any pins on the right-hand C/D connectors. (The only DEC card with a problem with this seems to have been the MMV11-A.)

It was available both with a front panel with a bezel (with 'Boot', 'Halt' and 'LTC On' switches, and power and run status indicators); and also with a blank front panel (for use as an expansion box).

It was a 5-1/4" tall mounting box, for the H960 series of 19"-wide racks, one of the BA11 mounting boxes. The H960 racks provided 63" of vertical mounting space, divided into units of 10-1/2", which were further subdividable into a pair of 5-1/4" spaces. The 5-1/4" tall BA11-N mounting box was designed for these spaces.

For rack mounting purposes. it did not use external slides (as all the other BA11 mounting boxes did); instead, it was housed in an external 'skin' (termed a 'logic box cover' in DEC documentation, the base unit being called a 'logic box') into which it is slid; the cover would be bolted to the rack.

The backplane was mounted vertically, facing backward (unlike the BA11-M mounting box, where they had been facing forward). Cooling fans mounted on the side of the BA11-N passed air both over the boards, and through the power supply.

The BA11-N's dimensions were 5-1/4" high, 19" wide, and 22-3/4" deep, and it weighed 44 lbs (without any boards). The rack mounting was 26-3/4" long.

See also

Further reading

  • BA11-N Mounting Box Technical Manual (EK-BA11N-TM-001) - not available online
  • BA11-N Mounting Box Illustrated Parts Breakdown (EK-BA11N-IP) - not available online

External links