Difference between revisions of "M782 Interrupt Control"
(Add m782 details) |
(Add 7820 image) |
||
| Line 1: | Line 1: | ||
| − | [[Image: | + | [[Image:M7820InterruptControl.jpg|250px|thumb|right|M7820 FLIP CHIP]] |
The '''M782 Interrupt Control''' (later versions M7820 and M7821) is a [[Digital Equipment Corporation|DEC]] [[FLIP CHIP]] which implements the '[[interrupt]] control' function for the [[UNIBUS]]. | The '''M782 Interrupt Control''' (later versions M7820 and M7821) is a [[Digital Equipment Corporation|DEC]] [[FLIP CHIP]] which implements the '[[interrupt]] control' function for the [[UNIBUS]]. | ||
It was used, along with an [[M105 Address Selector]], in early [[PDP-11]] [[device controller]]s which plugged into an [[Small Peripheral Controller|SPC]] slot. It was also used in a number of early devices which were built out of a custom [[backplane]] and a large number of FLIP CHIPs, such as the [[RK11|RK11-C]]. Some later devices which no longer used a large number of small Flip Chips (such as the [[TM11|TMB11]]) also used it. | It was used, along with an [[M105 Address Selector]], in early [[PDP-11]] [[device controller]]s which plugged into an [[Small Peripheral Controller|SPC]] slot. It was also used in a number of early devices which were built out of a custom [[backplane]] and a large number of FLIP CHIPs, such as the [[RK11|RK11-C]]. Some later devices which no longer used a large number of small Flip Chips (such as the [[TM11|TMB11]]) also used it. | ||
| + | |||
| + | [[Image:M7821InterruptControl.jpg|250px|thumb|left|M7821 FLIP CHIP]] | ||
The board contained a number of [[jumper]]s which could be use to set the [[interrupt vector]]. The M782 can set vector [[address]] [[bit]]s 3-7 (i.e. vectors from 0 through 0374); bit 2 (04) is controlled be the device's [[electronics]]. The M7820 has more jumpers, on address bits 2-8 (i.e. vectors of the form 0xx0 and 0xx4); bit 2 (04) can be controlled be either the device's electronics, or the jumper. | The board contained a number of [[jumper]]s which could be use to set the [[interrupt vector]]. The M782 can set vector [[address]] [[bit]]s 3-7 (i.e. vectors from 0 through 0374); bit 2 (04) is controlled be the device's [[electronics]]. The M7820 has more jumpers, on address bits 2-8 (i.e. vectors of the form 0xx0 and 0xx4); bit 2 (04) can be controlled be either the device's electronics, or the jumper. | ||
| − | |||
{{stub}} | {{stub}} | ||
Revision as of 00:35, 18 September 2018
The M782 Interrupt Control (later versions M7820 and M7821) is a DEC FLIP CHIP which implements the 'interrupt control' function for the UNIBUS.
It was used, along with an M105 Address Selector, in early PDP-11 device controllers which plugged into an SPC slot. It was also used in a number of early devices which were built out of a custom backplane and a large number of FLIP CHIPs, such as the RK11-C. Some later devices which no longer used a large number of small Flip Chips (such as the TMB11) also used it.
The board contained a number of jumpers which could be use to set the interrupt vector. The M782 can set vector address bits 3-7 (i.e. vectors from 0 through 0374); bit 2 (04) is controlled be the device's electronics. The M7820 has more jumpers, on address bits 2-8 (i.e. vectors of the form 0xx0 and 0xx4); bit 2 (04) can be controlled be either the device's electronics, or the jumper.
