DD11-B backplane - Revision history

Jnc: /* External links */ +Engineering Drawings

2023-03-27T13:15:59Z

‎External links: +Engineering Drawings

Jnc: Better cat

2022-12-05T17:02:07Z

Better cat

Jnc: DF11 support

2021-08-02T17:08:08Z

DF11 support

Jnc: The basics

2021-07-25T17:17:45Z

The basics

New page

The '''DD11-B backplane''' is a 4-slot [[UNIBUS]] [[backplane]] [[system unit]]. It was normally installed in a [[BA11 mounting boxes|BA11 mounting box]]. It used the early 9-pin [[DEC power distribution connectors]].

[[Category: DEC Hardware]]

← Older revision		Revision as of 13:15, 27 March 2023
Line 2:		Line 2:

	The two [[DEC card form factor\|hex-width]] slots were wired to support a [[DF11 Communications Line Adapter]] (in the A-B [[DEC edge connector contact identification\|connectors]]) along with a quad-width [[serial line]] [[device controller\|interface]], such as the [[DL11 asynchronous serial line interface\|DL11]] or the [[DU11 synchronous serial line interface\|DU11]].		The two [[DEC card form factor\|hex-width]] slots were wired to support a [[DF11 Communications Line Adapter]] (in the A-B [[DEC edge connector contact identification\|connectors]]) along with a quad-width [[serial line]] [[device controller\|interface]], such as the [[DL11 asynchronous serial line interface\|DL11]] or the [[DU11 synchronous serial line interface\|DU11]].
		+
		+	==External links==
		+
		+	* [http://www.bitsavers.org/pdf/dec/unibus/DD11-B_RevE_Engineering_Drawings_Feb74.pdf DD11-B Engineering Drawings]

	[[Category: UNIBUS Backplanes]]]		[[Category: UNIBUS Backplanes]]]

← Older revision		Revision as of 17:02, 5 December 2022
Line 3:		Line 3:
	The two [[DEC card form factor\|hex-width]] slots were wired to support a [[DF11 Communications Line Adapter]] (in the A-B [[DEC edge connector contact identification\|connectors]]) along with a quad-width [[serial line]] [[device controller\|interface]], such as the [[DL11 asynchronous serial line interface\|DL11]] or the [[DU11 synchronous serial line interface\|DU11]].		The two [[DEC card form factor\|hex-width]] slots were wired to support a [[DF11 Communications Line Adapter]] (in the A-B [[DEC edge connector contact identification\|connectors]]) along with a quad-width [[serial line]] [[device controller\|interface]], such as the [[DL11 asynchronous serial line interface\|DL11]] or the [[DU11 synchronous serial line interface\|DU11]].

−	[[Category: UNIBUS]]	+	[[Category: UNIBUS Backplanes]]]
−	~~[[Category: DEC Hardware~~]]

← Older revision		Revision as of 17:08, 2 August 2021
Line 1:		Line 1:
−	The '''DD11-B backplane''' is a 4-slot [[UNIBUS]] [[backplane]] [[system unit]]~~. It~~ was normally installed in a [[BA11 mounting boxes\|BA11 mounting box]]. It used the early 9-pin [[DEC power distribution connectors]].	+	The '''DD11-B backplane''' is a 4-slot [[UNIBUS]] [[backplane]] [[system unit]]; it was normally installed in a [[BA11 mounting boxes\|BA11 mounting box]]. It used the early 9-pin [[DEC power distribution connectors]].

		+	The two [[DEC card form factor\|hex-width]] slots were wired to support a [[DF11 Communications Line Adapter]] (in the A-B [[DEC edge connector contact identification\|connectors]]) along with a quad-width [[serial line]] [[device controller\|interface]], such as the [[DL11 asynchronous serial line interface\|DL11]] or the [[DU11 synchronous serial line interface\|DU11]].
		+
		+	[[Category: UNIBUS]]
	[[Category: DEC Hardware]]		[[Category: DEC Hardware]]