KDJ11 PMI/UNIBUS backplane - Revision history

Jnc: Move general description to introduction

2024-10-09T09:28:54Z

Move general description to introduction

Jnc: Fix title; improve diagram

2024-10-08T13:12:01Z

Fix title; improve diagram

Jnc: Add DEC part number

2024-10-08T11:31:19Z

Add DEC part number

Jnc: Move content to separate article to which all -11/84 and -11/94 board pages can refer

2024-10-07T22:41:57Z

Move content to separate article to which all -11/84 and -11/94 board pages can refer

New page

The '''KTJ11-B PMI/UNIBUS backplane''', '''H9277-A''', is used with the [[KDJ11-B CPU|KDJ11-B]] and [[KDJ11-E CPU|KDJ11-E]] [[QBUS]] [[Central Processing Unit|CPU]] cards, along with the [[KTJ11-B UNIBUS adapter]], to add [[UNIBUS]] capability to systems built around those CPU cards, the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.

==Backplane details==

The custom 12+1 slot [[backplane]] used with the KDJ11-B/E and KTJ11-B was half QBUS, and half UNIBUS (the 13th 'slot' is not a full slot, it only has a [[DEC edge connector contact identification|connector]] for one set of fingers). It has [[Private Memory Interconnect]] (PMI) bus slots at the top (for the CPU and [[main memory]] cards), a special slot in the middle for the KTJ11-B, and then UNIBUS slots.

In detail, the backplane contains (in order) four [[DEC card form factor|quad-height]] slots, the first of which is the custom partial slot, and the others are PMI (technically [[QBUS#Variable address size|Q22]]/[[CD interconnect|CD]], although slightly modified from the normal form of that in this backplane, see below); they are used for (in order, from the front of the machine):

* the Machine Debug Monitor board (M7677); this slot is not numbered
* the CPU board; this is slot 1
* main memory board
* optional second main memory board

and nine hex-height slots, used for:

* KTJ11-B UNIBUS adapter, in slot 4
* four [[Small Peripheral Controller|SPC]] UNIBUS slots
* three [[Modified UNIBUS Device|MUD]] UNIBUS slots
* UNIBUS 'out' and quad SPC slot, in slot 12

Note that the PMI slots do not have the [[Private Memory Interconnect#CD interconnect details|bottom-up]] ordering of PMI-capable slots in a Q22/CD backplane, but are wired as a true bus, allowing the 'CPU, memory, memory' insertion ordering seen here.

Note also that in the normal configuration (see below for details), the QBUS [[bus grant line]]s are not routed through the memory slots, so if one of these slots is unused, there is no need for a [[M9047 grant continuity card]] in that slot.

As a further feature, on most UNIBUS backplanes, the 'NPG' ([[Direct Memory Access|DMA]] grant line) signal is carried across unused slots by wire [[jumper]]s on [[wire-wrap]] pins on the back side of the backplane; on the -11/84 backplane, they are brought out to a [[Dual Inline Package|DIP]] switch on the MDM module, for easier configuration changes.

Any UNIBUS slot which does not have a device installed in it, must have a [[bus grant|grant]] continuity card such as a [[G7273 grant continuity card|G7273]] placed in it.

===Backplane layout===

Board locations are:


{| class="wikitable"
! !! colspan="6" | Connector
|-
! Slot !! A !! B !! C !! D !! E !! F
|-
| 0 || colspan="4" style="text-align:center;" | M7677 MDM
|-
| 1 || colspan="4" style="text-align:center;" | M8190 or M8981 CPU
|-
| 2 || colspan="4" style="text-align:center;" | PMI memory
|-
| 3 || colspan="4" style="text-align:center;" | PMI memory
|-
| 4 || colspan="6" style="text-align:center;" | M8191 UBA
|-
| 5 || colspan="6" style="text-align:center;" | SPC device
|-
| 6 || colspan="6" style="text-align:center;" | SPC device
|-
| 7 || colspan="6" style="text-align:center;" | SPC device
|-
| 8 || colspan="6" style="text-align:center;" | SPC device
|-
| 9 || colspan="6" style="text-align:center;" | MUD device
|-
| 10 || colspan="6" style="text-align:center;" | MUD device
|-
| 11 || colspan="6" style="text-align:center;" | MUD device
|-
| 12 || colspan="2" style="text-align:center;" | UNIBUS Out || colspan="4" style="text-align:center;" | SPC
|}

''Note:'' In an -11/94, there will usually be no PMI memory, but there will be an M9714 Alternate Power Source cards in connectors A-B of slot 2.

===QBUS slots===

The two main memory slots can in fact be configured as regular Q22/CD QBUS slots, by removing two jumpers. EK-PDP84-TM-PR4 (PDP-11/84 Technical Manual) says (in section 2.1.14, "Backplane (H9277-A)", pg. 2-6):

: ''Bus signals BDMGI (pin AR2) and BIAKI (pin AM2) for slots 2 & 3 are jumpered on the front of the backplane.''

There are indeed two jumpers, W1 and W2 (in the upper right-hand corner, when facing the backplane from the board insertion side); the traces connected to them are on the surface, so it is possible to see where they go: one end runs to a trace connected from slot 1 to slot 2, and the other to a trace connected from slot 3 to slot 4; those connect to AM2 (BIAKI) and AN2 (BIAKO), and AR2 (BDMGI) and AS2 (BDMGO).

Thus, when the jumpers are in, the CPU's BIAKO/BDMGO pins are connected directly to the UNIBUS adapter's BIAKI/BDMGI pins; when they are out, those signals are routed through the two 'memory' slots, in the normal QBUS manner.

It therefore seems those two slots ''might'' be able to function as real QBUS slots. However, it is not clear that the CPU will 'do the right thing'; the UNIBUS adapter puts out a signal to let the CPU know that it is there, and the CPU may then expect to see only PMI-type DMA and [[interrupt]] cycles on the bus.

The DMA cycle ''might'' work, it all depends on what happens at step 8 (EK-KDJ1B-UG-001, pp. 7-6 to 7-9) when, instead of PBSY being asserted, BSYNC is asserted. The PMI ''memory'' will be fine (since in an -11/83, this kind of thing is expected)... but the ''CPU'', who knows. (The CPU would do the right thing in an -11/83, but the same board might not do the right thing here, since it 'knows' there is a UNIBUS adapter present.)

Interrupt cycles are more problematic; the assertion of the interrupt level on the BDAL lines (step 1a) will probably pass, but step 6 (assertion of BSACK) may be an issue, since the device will want to assert BRPLY instead (BSACK is not used in a QBUS interrupt), and the CPU may not do the right thing.

==External links==

* [http://www.bitsavers.org/pdf/dec/pdp11/1184/EK-1184E-TM-001_Dec87.pdf PDP-11/84 System Technical and Reference Manual] (EK-1184E-TM-001)
* [http://www.bitsavers.org/pdf/dec/pdp11/handbooks/PDP-11_Systems_Handbook_1987.pdf PDP-11 Systems Handbook] (EB 29317 41) - the overall architecture that the H9277-A implements is covered on pp. 127-129 of the PDF
* [http://www.bitsavers.org/pdf/dec/pdp11/1184/MP-02015-01_11-84_Maintenance_Print_Set_198412.pdf 11/84 Field Maintenance Print Set (MP-02015-001)] - the H9277-A is covered on pp. 16-22 of the PDF

[[Category: UNIBUS]]
[[Category: Private Memory Interconnect]]

@@ Line 1: / Line 1: @@
-The '''KDJ11 PMI/UNIBUS backplane''', '''H9277-A''' ([[DEC part number]] 70-20650-01), is used with the [[KTJ11-B UNIBUS adapter]], along with the [[KDJ11-B CPU|KDJ11-B]] and [[KDJ11-E CPU|KDJ11-E]] [[QBUS]] [[Central Processing Unit|CPU]] cards, to provide [[UNIBUS]] capability to systems built around those CPU cards; the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.
+The '''KDJ11 PMI/UNIBUS backplane''', '''H9277-A''', is used with the [[KTJ11-B UNIBUS adapter]], along with the [[KDJ11-B CPU|KDJ11-B]] and [[KDJ11-E CPU|KDJ11-E]] [[QBUS]] [[Central Processing Unit|CPU]] cards, to provide [[UNIBUS]] capability to systems built around those CPU cards; the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.
-==Backplane details==
+The custom 12+1 slot [[backplane]] ([[DEC part number]] 70-20650-01) was half [[Private Memory Interconnect]] (PMI; a variant of the [[QBUS]]), and half UNIBUS. (The 13th 'slot' is not a full slot, it only has a [[DEC edge connector contact identification|connector]] for one set of fingers.) It has PMI bus slots at the top (for the CPU and [[main memory]] cards), a special slot in the middle for the KTJ11-B, and then UNIBUS slots.
-The custom 12+1 slot [[backplane]] used with the KDJ11-B/E and KTJ11-B was half [[Private Memory Interconnect]] (PMI; a variant of the [[QBUS]]), and half UNIBUS (the 13th 'slot' is not a full slot, it only has a [[DEC edge connector contact identification|connector]] for one set of fingers). It has PMI bus slots at the top (for the CPU and [[main memory]] cards), a special slot in the middle for the KTJ11-B, and then UNIBUS slots.
+==Technical details==
-In detail, the backplane contains (in order) four [[DEC card form factor|quad-height]] slots, the first of which is the custom partial slot, and the others are PMI (technically [[QBUS#Variable address size|Q22]]/[[CD interconnect|CD]], although slightly modified from the normal form of that in this backplane, see below); they are used for (in order, from the front of the machine):
+The backplane contains (in order) four [[DEC card form factor|quad-height]] slots, the first of which is the custom partial slot, and the others are PMI (technically [[QBUS#Variable address size|Q22]]/[[CD interconnect|CD]], although slightly modified from the normal form of that in this backplane, see below); they are used for (in order, from the front of the machine):
 * the Machine Debug Monitor board (M7677); this slot is not numbered
@@ Line 15: / Line 15: @@
 * KTJ11-B UNIBUS adapter, in slot 4
-* four [[Small Peripheral Controller|SPC]] UNIBUS slots
+* four quad [[Small Peripheral Controller|SPC]] UNIBUS slots
 * three [[Modified UNIBUS Device|MUD]] UNIBUS slots
 * UNIBUS 'out' and quad SPC slot, in slot 12

← Older revision		Revision as of 11:31, 8 October 2024
Line 1:		Line 1:
−	The '''KTJ11-B PMI/UNIBUS backplane''', '''H9277-A''', is used with the [[KDJ11-B CPU\|KDJ11-B]] and [[KDJ11-E CPU\|KDJ11-E]] [[QBUS]] [[Central Processing Unit\|CPU]] cards, along with the [[KTJ11-B UNIBUS adapter]], to add [[UNIBUS]] capability to systems built around those CPU cards, the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.	+	The '''KTJ11-B PMI/UNIBUS backplane''', '''H9277-A''' ([[DEC part number]] 70-20650-01), is used with the [[KDJ11-B CPU\|KDJ11-B]] and [[KDJ11-E CPU\|KDJ11-E]] [[QBUS]] [[Central Processing Unit\|CPU]] cards, along with the [[KTJ11-B UNIBUS adapter]], to add [[UNIBUS]] capability to systems built around those CPU cards, the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.

	==Backplane details==		==Backplane details==

@@ Line 1: / Line 1: @@
-The '''KTJ11-B PMI/UNIBUS backplane''', '''H9277-A''' ([[DEC part number]] 70-20650-01), is used with the [[KDJ11-B CPU|KDJ11-B]] and [[KDJ11-E CPU|KDJ11-E]] [[QBUS]] [[Central Processing Unit|CPU]] cards, along with the [[KTJ11-B UNIBUS adapter]], to add [[UNIBUS]] capability to systems built around those CPU cards, the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.
+The '''KDJ11 PMI/UNIBUS backplane''', '''H9277-A''' ([[DEC part number]] 70-20650-01), is used with the [[KTJ11-B UNIBUS adapter]], along with the [[KDJ11-B CPU|KDJ11-B]] and [[KDJ11-E CPU|KDJ11-E]] [[QBUS]] [[Central Processing Unit|CPU]] cards, to provide [[UNIBUS]] capability to systems built around those CPU cards; the [[PDP-11/84]] and [[PDP-11/94]] systems respectively.
 ==Backplane details==
-The custom 12+1 slot [[backplane]] used with the KDJ11-B/E and KTJ11-B was half QBUS, and half UNIBUS (the 13th 'slot' is not a full slot, it only has a [[DEC edge connector contact identification|connector]] for one set of fingers). It has [[Private Memory Interconnect]] (PMI) bus slots at the top (for the CPU and [[main memory]] cards), a special slot in the middle for the KTJ11-B, and then UNIBUS slots.
+The custom 12+1 slot [[backplane]] used with the KDJ11-B/E and KTJ11-B was half [[Private Memory Interconnect]] (PMI; a variant of the [[QBUS]]), and half UNIBUS (the 13th 'slot' is not a full slot, it only has a [[DEC edge connector contact identification|connector]] for one set of fingers). It has PMI bus slots at the top (for the CPU and [[main memory]] cards), a special slot in the middle for the KTJ11-B, and then UNIBUS slots.
 In detail, the backplane contains (in order) four [[DEC card form factor|quad-height]] slots, the first of which is the custom partial slot, and the others are PMI (technically [[QBUS#Variable address size|Q22]]/[[CD interconnect|CD]], although slightly modified from the normal form of that in this backplane, see below); they are used for (in order, from the front of the machine):
@@ Line 19: / Line 19: @@
 * UNIBUS 'out' and quad SPC slot, in slot 12
-Note that the PMI slots do not have the [[Private Memory Interconnect#CD interconnect details|bottom-up]] ordering of PMI-capable slots in a Q22/CD backplane, but are wired as a true bus, allowing the 'CPU, memory, memory' insertion ordering seen here.
+Note that the PMI slots do not have the [[Private Memory Interconnect#CD interconnect details|bottom-up]] ordering of PMI-capable slots in a Q22/CD backplane, but are wired as a true bus (fully interconnected), allowing the 'CPU, memory, memory' insertion ordering seen here.
 Note also that in the normal configuration (see below for details), the QBUS [[bus grant line]]s are not routed through the memory slots, so if one of these slots is unused, there is no need for a [[M9047 grant continuity card]] in that slot.
@@ Line 35: / Line 35: @@
 ! !! colspan="6" | Connector
 |-
-! Slot !! A !! B !! C !! D !! E !! F
+! Slot !! A !! B !! &nbsp; C &nbsp; !! &nbsp; D &nbsp; !! &nbsp; E &nbsp; !! &nbsp; F &nbsp;
 |-
-| 0 || colspan="4" style="text-align:center;" | M7677 MDM
+| 0 || colspan="4" style="text-align:center;" | M7677 MDM || colspan="2" | &nbsp;
 |-
-| 1 || colspan="4" style="text-align:center;" | M8190 or M8981 CPU
+| 1 || colspan="4" style="text-align:center;" | M8190 or M8981 CPU || colspan="2" | &nbsp;
 |-
-| 2 || colspan="4" style="text-align:center;" | PMI memory
+| 2 || colspan="4" style="text-align:center;" | PMI memory || colspan="2" | &nbsp;
 |-
-| 3 || colspan="4" style="text-align:center;" | PMI memory
+| 3 || colspan="4" style="text-align:center;" | PMI memory || colspan="2" | &nbsp;
 |-
 | 4 || colspan="6" style="text-align:center;" | M8191 UBA
 |-
-| 5 || colspan="6" style="text-align:center;" | SPC device
+| 5 || colspan="2" | &nbsp; || colspan="4" style="text-align:center;" | SPC device
 |-
-| 6 || colspan="6" style="text-align:center;" | SPC device
+| 6 || colspan="2" | &nbsp; || colspan="4" style="text-align:center;" | SPC device
 |-
-| 7 || colspan="6" style="text-align:center;" | SPC device
+| 7 || colspan="2" | &nbsp; || colspan="4" style="text-align:center;" | SPC device
 |-
-| 8 || colspan="6" style="text-align:center;" | SPC device
+| 8 || colspan="2" | &nbsp; || colspan="4" style="text-align:center;" | SPC device
 |-
 | 9 || colspan="6" style="text-align:center;" | MUD device
@@ Line 61: / Line 61: @@
 | 11 || colspan="6" style="text-align:center;" | MUD device
 |-
-| 12 || colspan="2" style="text-align:center;" | UNIBUS Out || colspan="4" style="text-align:center;" | SPC
+| 12 || colspan="2" style="text-align:center;" | UNIBUS Out || colspan="4" style="text-align:center;" | SPC device
 |}
-''Note:'' In an -11/94, there will usually be no PMI memory, but there will be an M9714 Alternate Power Source cards in connectors A-B of slot 2.
+''Note:'' In an -11/94, there will usually be no PMI memory, but there will be an M9714 Alternate Power Source card in connectors A-B of slot 2.
 ===QBUS slots===