Difference between revisions of "FLIP CHIP"
m (typo) |
|||
| Line 1: | Line 1: | ||
| − | ''' | + | {{DEC-HW-stub}} |
| + | [[Image:B Series Flip Chip.jpg|thumb|300px|A B series Flip-Chip]] | ||
| + | '''Flip-Chip''' was a [[DEC]] registered trademark, named after the "flipchip" component mounting technique which quite rapidly faded from fame. The name was retained although the majority of Flip-Chips never really were flipchip-mounted as it became apparent that the flipchip mounting technique was highly unreliable. Flip-chips were used in the DEC [[PDP-7]] (Referred to in documentation as the "FLIP CHIP"), [[PDP-8]], [[PDP-9]] and [[PDP-10]], beginning on August 24, 1964. | ||
| − | They were | + | In practice, they performed generic, simple functions, similar to an integrated circuit. They were approximately 4 inches long and 2.5 inches wide. Each had 36 connectors, 18 on each side. |
| − | + | == Naming == | |
| − | + | There appeared to be some confusion inside DEC at the time, as various manuals refer to it as "FLIP CHIP", "Flip Chip", "FLIP-CHIP", "Flip-Chip" and "Flip Chip", with trademark and registered trademark symbols. | |
| − | + | ==Flip-Chip families== | |
| − | |||
| − | + | [[Image:FlipChips.jpeg|thumb|250px|Flip-chips in different forms and a rainbow of colours, in a [[PDP-8]].]] | |
| − | + | The various families were colour-coded, and the first letter denoted a colour, which was also visible on the handle. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | ===A series=== | |
| − | + | ''See the list of [[List of DEC part numbers#A series|DEC parts]].'' | |
| − | + | The A stands for Amber. The A series were used for analog functions - ADCs, DACs, amplifiers etc. | |
| − | * | + | |
| − | * | + | ===B series=== |
| + | |||
| + | The B stands for Blue. The B series were used as core logic in the higher-end CPUs. | ||
| + | |||
| + | ===G series=== | ||
| + | |||
| + | The G stands for Green. The G series were used for "anything with non-standard voltages", I think. | ||
| + | |||
| + | ===M series=== | ||
| + | |||
| + | ''See the list of [[List of DEC part numbers#M series|DEC parts]]. | ||
| + | |||
| + | The M stands for magenta. Part of this line is simple TTL-level logic, while later on, it became quite complex, see [[list of DEC part numbers]]. They replaced the R series which used discrete transistors with integrated circuits. | ||
| + | |||
| + | * Power supply: 5 V | ||
| + | * Operate at up to 6 MHz | ||
| + | |||
| + | ===R series=== | ||
| + | |||
| + | The R stands for Red. Slower logic than the B series, but cheaper. Used extensively in the I/O circuitry of computers. | ||
| + | |||
| + | * Slower logic than B series, cheaper | ||
| + | * Used in a variety of systems, e.g. [[PDP-8]] | ||
| + | * Power supply 10 and -15 volts | ||
| + | * Operational to 2 megahertz | ||
| + | * Signal level 0 volts, logic 0 and -3 volts, logic 1 | ||
| + | * Typical price $20 to $30 | ||
| + | |||
| + | === S series === | ||
| + | |||
| + | The S series is identical to the R seriese except that its transistors switch faster and lower resistance resistors, allowing more cards to be wired in series and operate somewhat faster. | ||
| + | |||
| + | ===W series=== | ||
| + | |||
| + | The W stands for White. These are components that plug into Flip-Chip sockets, but have no logic of their own. | ||
Revision as of 20:39, 29 July 2017
Flip-Chip was a DEC registered trademark, named after the "flipchip" component mounting technique which quite rapidly faded from fame. The name was retained although the majority of Flip-Chips never really were flipchip-mounted as it became apparent that the flipchip mounting technique was highly unreliable. Flip-chips were used in the DEC PDP-7 (Referred to in documentation as the "FLIP CHIP"), PDP-8, PDP-9 and PDP-10, beginning on August 24, 1964.
In practice, they performed generic, simple functions, similar to an integrated circuit. They were approximately 4 inches long and 2.5 inches wide. Each had 36 connectors, 18 on each side.
Contents
Naming
There appeared to be some confusion inside DEC at the time, as various manuals refer to it as "FLIP CHIP", "Flip Chip", "FLIP-CHIP", "Flip-Chip" and "Flip Chip", with trademark and registered trademark symbols.
Flip-Chip families
The various families were colour-coded, and the first letter denoted a colour, which was also visible on the handle.
A series
See the list of DEC parts.
The A stands for Amber. The A series were used for analog functions - ADCs, DACs, amplifiers etc.
B series
The B stands for Blue. The B series were used as core logic in the higher-end CPUs.
G series
The G stands for Green. The G series were used for "anything with non-standard voltages", I think.
M series
See the list of DEC parts.
The M stands for magenta. Part of this line is simple TTL-level logic, while later on, it became quite complex, see list of DEC part numbers. They replaced the R series which used discrete transistors with integrated circuits.
- Power supply: 5 V
- Operate at up to 6 MHz
R series
The R stands for Red. Slower logic than the B series, but cheaper. Used extensively in the I/O circuitry of computers.
- Slower logic than B series, cheaper
- Used in a variety of systems, e.g. PDP-8
- Power supply 10 and -15 volts
- Operational to 2 megahertz
- Signal level 0 volts, logic 0 and -3 volts, logic 1
- Typical price $20 to $30
S series
The S series is identical to the R seriese except that its transistors switch faster and lower resistance resistors, allowing more cards to be wired in series and operate somewhat faster.
