Difference between revisions of "KDF11 CPUs"

From Computer History Wiki
Jump to: navigation, search
m (+links)
(Add links, copyedit)
Line 5: Line 5:
 
*[[KDF11-U CPU]] - M7133 - [[UNIBUS]] hex-width CPU used in the [[PDP-11/24]]
 
*[[KDF11-U CPU]] - M7133 - [[UNIBUS]] hex-width CPU used in the [[PDP-11/24]]
  
Like the [[LSI-11]] models, as a cost-reduction measure they do not have a [[front panel]] to control them; instead, when the CPU is halted, specialized [[microcode]] used the main [[asynchronous serial line]] as a operating console. The command set is named Octal Debugging Technique (ODT); there are commands to read and write [[main memory]], start the CPU, etc. The main serial interface is normally configured so that when the CPU is running, sending a [[asynchronous serial line|break]] on the console serial line [[halt]]s the CPU.
+
Like the [[LSI-11]] models, as a cost-reduction measure they do not have a [[front panel]] to control them; instead, when the CPU is halted, specialized [[microcode]] used the main [[asynchronous serial line]] as a operating console. The command set is named Octal Debugging Technique (ODT); there are commands to read and write [[main memory]], start the CPU, etc.
 +
 
 +
The main [[asynchronous serial line|serial]] [[device controller|interface]] is normally configured so that when the CPU is running, sending a [[asynchronous serial line|break]] on the console serial line [[halt]]s the CPU.
  
 
==Floating point==
 
==Floating point==
  
All the KDF11 CPUs have two choices for [[floating point]] support (full PDP-11 [[FP11 floating point]]): a on-board single [[integrated circuit|chip]], the [[KEF11-A floating point chip]], which implements floating point using microcode; and a higher-performance separate [[DEC card form factor|quad]] board, the [[FPF11]] (M8188).
+
All the KDF11 CPUs have two choices for [[floating point]] support (full PDP-11 [[FP11 floating point]]): a on-board single [[integrated circuit|chip]], the [[KEF11-A floating point chip]], which implements floating point using microcode; and a higher-performance [[co-processor]] on a separate [[DEC card form factor|quad]] board, the [[FPF11 floating point processor‎|FPF11]] (M8188).
  
The FPF11 communicates with the KDF11 via a [[flat cable]] that plugs into the [[chip socket]] on the KDF11 where the KEF11-A is installed; is unusual that it can plug into either a QBUS or UNIBUS [[backplane]], since it only draws power from the backplane - all [[signal]]s come over the cable to the KDF11.
+
The FPF11 communicates with the KDF11 via a [[flat cable]] that plugs into the [[chip socket]] on the KDF11 where the KEF11-A is installed; is unusual that it can plug into either a QBUS or UNIBUS [[backplane]], since it draws only power from the backplane - all [[signal]]s come over the cable to the KDF11.
  
 
{{PDP-11}}
 
{{PDP-11}}
  
 
[[Category: PDP-11 Processors]]
 
[[Category: PDP-11 Processors]]

Revision as of 05:36, 18 November 2018

There are several single-board PDP-11 CPUs which all use the 'Fonz' F-11 chip set:

Like the LSI-11 models, as a cost-reduction measure they do not have a front panel to control them; instead, when the CPU is halted, specialized microcode used the main asynchronous serial line as a operating console. The command set is named Octal Debugging Technique (ODT); there are commands to read and write main memory, start the CPU, etc.

The main serial interface is normally configured so that when the CPU is running, sending a break on the console serial line halts the CPU.

Floating point

All the KDF11 CPUs have two choices for floating point support (full PDP-11 FP11 floating point): a on-board single chip, the KEF11-A floating point chip, which implements floating point using microcode; and a higher-performance co-processor on a separate quad board, the FPF11 (M8188).

The FPF11 communicates with the KDF11 via a flat cable that plugs into the chip socket on the KDF11 where the KEF11-A is installed; is unusual that it can plug into either a QBUS or UNIBUS backplane, since it draws only power from the backplane - all signals come over the cable to the KDF11.