Difference between revisions of "MM11-E and MM1-F core memories"
m (+cat) |
m (→External links: +Manuals, eng drws) |
||
| Line 34: | Line 34: | ||
The M1091 could be used in the MM11-E as well as the MM11-F; it appears that later units of the MM11-E shipped with the M1091. The difference between the M109 and M1091 is the addition of additional [[jumper]]s to allow interleaving. | The M1091 could be used in the MM11-E as well as the MM11-F; it appears that later units of the MM11-E shipped with the M1091. The difference between the M109 and M1091 is the addition of additional [[jumper]]s to allow interleaving. | ||
| − | + | ==External links== | |
| + | |||
| + | * [http://bitsavers.org/pdf/dec/pdp11/memory/MM11-E_CoreMemoryManual.pdf MM11-E Core Memory Manual] (DEC-11-HR3A-D) - includes engineering drawings on pp. 24-41 | ||
| + | * [http://ana-3.lcs.mit.edu/~jnc/tech/pdp11/dload/DEC-11-HMFA-D_MM11-F_Manual.pdf MM11-F core memory manual] (DEC-11-HMFA-D) | ||
| + | ** [http://ana-3.lcs.mit.edu/~jnc/tech/pdp11/dload/MM11-F_Manual.tar MM11-F core memory manual] - scans of individual pages in a [[tar]] file | ||
| + | * [http://ana-3.lcs.mit.edu/~jnc/tech/pdp11/dload/DEC-11-HMFA-D_MM11-F_Drawings.pdf MM11-F core memory engineering drawings] (DEC-11-HMFA-D) | ||
| + | ** [http://ana-3.lcs.mit.edu/~jnc/tech/pdp11/dload/MM11-F_Drawings.tar MM11-F ore memory engineering drawings] - scans of individual pages in a tar file | ||
[[Category: UNIBUS Memories]] | [[Category: UNIBUS Memories]] | ||
Revision as of 13:51, 16 October 2021
The MM11-E and MM11-F core memories were UNIBUS main memory units; the first UNIBUS memories produced by DEC. They came out with/for the first PDP-11, the PDP-11/20.
They were very similar - both 4K word (8K bytes), and with most of their boards in common. The MM11-F was capable of interleaving (although this capability was then made available to the MM11-E as well); it also had a parity version available, the MM11-FP (which used a 4Kx18 core plane, instead of the 4Kx16 used in the MM11-E and MM11-F).
The MM11-F was also slightly faster: the MM11-E had an access time of 500 nsec and a cycle time of 1.2 μsec; the MM11-F had an access time of 400 nsec and a cycle time of 980 nsec.
Both consisted of a quad-width H207 (non-parity) or H210 (parity) core plane board, along with a number of dual- and single-width cards (all extended-length), plugged into a custom-wired quad system unit. The MM11-F and MM11-FP used the same backplane; only the board set was slightly different
Board locations
These are the board locations for the MM11-E, -F and -FP (as seen from the board side of the backplane):
| Connector | Slot 4 | Slot 3 | Slot 2 | Slot 1 |
|---|---|---|---|---|
| A | UNIBUS Out |
Power | UNIBUS In | |
| B | G225% | M109! | ||
| C | H207 or H210 |
G226 | G226 | M729@ or M7290% |
| D | G102 | G102 | ||
| E | G102 | G102 | ++ | |
| F | G226 | G226 | G103 |
++ = G225 (MM11-E) or G108 (MM11-FP)
@ = MM11-E only
% = MM11-F and -FP only
! = Possibly the later M1091
The M1091 could be used in the MM11-E as well as the MM11-F; it appears that later units of the MM11-E shipped with the M1091. The difference between the M109 and M1091 is the addition of additional jumpers to allow interleaving.
External links
- MM11-E Core Memory Manual (DEC-11-HR3A-D) - includes engineering drawings on pp. 24-41
- MM11-F core memory manual (DEC-11-HMFA-D)
- MM11-F core memory manual - scans of individual pages in a tar file
- MM11-F core memory engineering drawings (DEC-11-HMFA-D)
- MM11-F ore memory engineering drawings - scans of individual pages in a tar file
