MM11-U core memory

From Computer History Wiki
Revision as of 20:59, 16 July 2019 by Jnc (talk | contribs) (+ bplane part #)
Jump to: navigation, search

The MM11-U was a popular, and fairly common, 32 Kbyte core memory for the early PDP-11 UNIBUS machines. An MM11-U was composed of a four board set:

  • G114 - hex-format sense/inhibit module
  • G235 - hex-format XY Drive, current source, decode module
  • H217-D - hex-format core stack
  • M7293 - quad-format timing and control module

There was also a parity-capable variant, the MM11-UP, which added an M7259 dual-format parity controller, and substituted an H217-C (with two more bits per word) for the H217-D.

The MM11-U/UP usually required a custom nine-slot backplane (part #5410345), although some CPU's (e.g. the PDP-11/05) had processor backplanes wired to hold an MM11-U set as well as the CPU set (but not the -UP, which required an extra slot for the M7259 parity controller).

The MF11-U was a backplane plus a single MM11-U board set; the backplane has room for one more MM11-U board set. The MF11-UP is the parity version.

Parity and non-parity backplane configuration

Installing an MM11-U (non-parity) module set in an MF11-UP backplane will cause the machine to hang when that memory is referenced.

This is because during parity operation, the SSYN signal is routed through the M7259 Parity Controller board, and that only issues the SSYN once it has checked that the parity is OK. On non-parity installations, the 'proto-SSYN' from the rest of the memory is just hard-wired straight to the output to the UNIBUS.

That requires a jumper on the backplane for non-parity memory: it runs from pin B1U1 to B2U1. This jumper should not be present for parity memory. Note that therefore parity and non-parity memory cannot be mixed on the same backplane.

G235 jumpers

The MM11-U manual (EK-MF11U-MM-003) describes (pg. 3-12) a set of jumpers (W5-W7) on the G235 card (X and Y selection line current generators - those for the inhibit lines are on the G114) which adjust the bias current for the selection line generators. It goes on to say:

Jumpers W5-W7 are factory cut to adjust the bias current to its optimal value and they should not be changed.

There is apparently a similar adjustment for the timing of the sense strobe.

The original procedure for setting those jumpers is likely lost, as it is probably only in some internal DEC documentation. The manual says (Section 5.4.2, "Sense Strobe Delay and Drive Current Adjustments"):

Correction of any failure in either the sense strobe delay or drive current circuits on the G235 module that would require reconfiguration of the jumpers within these circuits should not attempted in the field. Replace the faulty module with a spare G235 module and return the faulty G235 module to the factor for repair.

There is a test to know if the bias current is properly adjusted (see Section 5.3.4, "Drive Current Checks"), and also for the strobe delay (Section 5.3.3, "Sense Strobe Delay Checks"). So in theory, if a G235 card fails one of these tests, it should be possible to change the smallest value jumper, and see if that made things worse or better; and then loop.

Board inter-changeability

There was some concern that these boards were 'tuned' to be part of a set. E.g. one of the components, in the circuit that the W5-W7 jumpers are part of, is a thermistor on the core stack board (H217). It is not clear if the jumpers are just for dealing with component variations on the G235 board, or if they also include variation elsewhere. In other words, there was a possibility that MM11-U's came as tuned board sets, which should not be 'mixed and matched'.

However, the second block of text above alleviated that concern: apparently one can replace one G235 with another, without swapping out all the boards in the set.

Thus, any 'mixing and matching' that has happened to these boards if they were removed from their machines has probably not caused any problems.

See also