Difference between revisions of "MS11-L MOS memory"

From Computer History Wiki
Jump to: navigation, search
(Dual voltage)
(+Image)
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
The '''MS11-L''' was final [[UNIBUS]] [[main memory]] from [[Digital Equipment Corporation|DEC]]; a single card can hold enough [[Metal Oxide Semiconductor|MOS]] [[Dynamic RAM|DRAM]] [[integrated circuit|chips]] to fill the entire UNIBUS [[address space]]. It had a [[jumper]] option to enable use on an [[Extended UNIBUS]].
+
[[Image:MS11-L.jpg|300px|thumb|right|MS11-L board]]
  
Fully populated with 16Kx1 chips, it is known as the '''MS11-LD''', and holds 256K [[byte]]s. The quarter-, half- and three-quarter-populated versions are the '''MS11-LA''', '''-LB''' and '''-LC''', respectively; with 64KB, 128KB and 192KB. All versions include on-board [[parity]] support.
+
The '''MS11-L''' was final [[UNIBUS]] [[main memory]] from [[Digital Equipment Corporation|DEC]]; a single card can hold enough [[Metal Oxide Semiconductor|MOS]] [[Dynamic RAM|DRAM]] [[integrated circuit|chips]] to fill the entire UNIBUS [[address space]]. It had a [[jumper]] option to enable use on an [[Extended UNIBUS]]. Configuration is by [[Dual Inline Package|DIP]] switches. It used on-board[[parity]] for error detection.
 +
 
 +
Fully populated with 16Kx1 chips, it is known as the '''MS11-LD''', and holds 256K [[byte]]s. The quarter-, half- and three-quarter-populated versions are the '''MS11-LA''', '''-LB''' and '''-LC''', respectively; with 64KB, 128KB and 192KB.
  
 
It plugs into a [[Modified UNIBUS Device|MUD]] [[backplane]] (only; not [[Small Peripheral Controller|SPC]]). It is a single [[DEC card form factor|hex]] card, the M7891, so it cannot go in the end slots of the backplane.
 
It plugs into a [[Modified UNIBUS Device|MUD]] [[backplane]] (only; not [[Small Peripheral Controller|SPC]]). It is a single [[DEC card form factor|hex]] card, the M7891, so it cannot go in the end slots of the backplane.
Line 7: Line 9:
 
The [[access time]] is 385 nsec (typical; 1025 nsec maximum on [[refresh]] conflict), and the [[cycle time]] is 510 nsec (1050 nsec maximum on refresh conflict). Refresh time is 570 nsec (typical; 610 nsec maximum); the time for a complete refresh pass is 14.5 μsec (typical), 13.5 μsec (minimum).
 
The [[access time]] is 385 nsec (typical; 1025 nsec maximum on [[refresh]] conflict), and the [[cycle time]] is 510 nsec (1050 nsec maximum on refresh conflict). Refresh time is 570 nsec (typical; 610 nsec maximum); the time for a complete refresh pass is 14.5 μsec (typical), 13.5 μsec (minimum).
  
It can use ''either'' +/-15V or +/12V to power the memory chips (in some MUD slots, the 15V pins provide 12V). The board has provision to use battery backup power to retain data during a power outage. Configuration is by [[Dual Inline Package|DIP]] switches.
+
It can use ''either'' +/-15V or +/-12V to power the memory chips (in some MUD slots, the 15V pins provide 12V). The board has provision to use battery backup power to retain data during a power outage. Power requirements are 1.5-1.8A of +5V, 1-1.3A of +5VBB, 9-20mA of -12/-15V (depending on size, i.e. number of MOS memory chips), and 485-700 mA of +12/+15 (when active; depending on size).
  
 
{{PDP-11}}
 
{{PDP-11}}

Revision as of 19:53, 25 January 2020

MS11-L board

The MS11-L was final UNIBUS main memory from DEC; a single card can hold enough MOS DRAM chips to fill the entire UNIBUS address space. It had a jumper option to enable use on an Extended UNIBUS. Configuration is by DIP switches. It used on-boardparity for error detection.

Fully populated with 16Kx1 chips, it is known as the MS11-LD, and holds 256K bytes. The quarter-, half- and three-quarter-populated versions are the MS11-LA, -LB and -LC, respectively; with 64KB, 128KB and 192KB.

It plugs into a MUD backplane (only; not SPC). It is a single hex card, the M7891, so it cannot go in the end slots of the backplane.

The access time is 385 nsec (typical; 1025 nsec maximum on refresh conflict), and the cycle time is 510 nsec (1050 nsec maximum on refresh conflict). Refresh time is 570 nsec (typical; 610 nsec maximum); the time for a complete refresh pass is 14.5 μsec (typical), 13.5 μsec (minimum).

It can use either +/-15V or +/-12V to power the memory chips (in some MUD slots, the 15V pins provide 12V). The board has provision to use battery backup power to retain data during a power outage. Power requirements are 1.5-1.8A of +5V, 1-1.3A of +5VBB, 9-20mA of -12/-15V (depending on size, i.e. number of MOS memory chips), and 485-700 mA of +12/+15 (when active; depending on size).