DL10 PDP-11 Data Link

The DL10 PDP-10/PDP-11 Interface Channel connects PDP-10 mainframes to PDP-11s used as communication front ends; up to 4 PDP-11's per DL10. It allows the PDP-10 to 'see' into the PDP-11's main memory, and vice versa (although the ability of the PDP-11 to do so is limited by the DL10's settings).

On the PDP-10 side, it connected to the PDP-10 memory bus, and also to two I/O busses (allowing it to be controlled by both processors in a multi-CPU system. So, it could be connected to KA10s and KI10s, but only to KL10s with the optional old-style I/O busses.

On the PDP-11 side, PDP-11's connected to the DL10 have a special console which has a cable which goes to the DL10, which allows the PDP-10 to start and stop the PDP-11; the PDP-11's UNIBUS runs into the DL10 and is plugged into the DL10's backplane.

Data formats

Note that the format is selected by the second octed in the word; the values used in that octet to select the byte size in the 'pointer' mode are disjoint from the values used in that octet for the other modes.

Immediate mode

Unused			0 or 7			Unused														Data
00	01	02	03	04	05	06	07	08	09	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35

Indirect mode

A	P		1			Unused								Address
00	01	02	03	04	05	06	07	08	09	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35

A	Access
0	Read or write
1	Read only

P	16-bit word position within 36-bit word
0	Bits 0-15
1	Bits 16-31
2	Bits 20-35
3	Bits 2-17

Pointer modes

P			S			Word count								Address
00	01	02	03	04	05	06	07	08	09	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35

Bytes are left-justified inside a 36-bit word.

S	Byte size
2	16
3	12
4	8
5	7
6	6

PDP-11 control and status registers

DATO 100000 (Conditions out)

Set 11 interrupt	Clear 11 interrupt	Set 10 interrupt	Clear 10 interrupt	Set nonex memory	Clear nonex memory	Set parity error	Clear parity error	Set word count overflow	Clear word count overflow			Error interrupt enable	11 interrupt enable	Interrupt assignment
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

DATI 100000 (Status)

11 interrupt		10 interrupt		Nonex memory		Set parity error		Word count overflow		This port enabled		Error interrupt enable	11 interrupt enable	Interrupt assignment
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

PDP-10 standard instructions

CONO DLB,

Base address												Mask for size of pointer block				PDP-11
18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35

CONO DLC,

Clear DL10	Lock DL10	11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	Priority interrupt assignment
18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35

CONI DLB,

Diag	Diag msyn	Diag C0	Diag C1	Diag R2	Diag R1	Diag INH CYC		11-3 8K option	11-2 8K option	11-1 8K option	11-0 8K option	IOC lock on	~IOC lock delay on	~IOC lock 1 out	~IOC lock 0 out	18-bit address		Got DL10 locked		11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	11 interrupt	Port enable	10 interrupt	Priority interrupt assignment
00	01	02	03	04	05	06	07	08	09	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35