Difference between revisions of "DEC standard modular regulators"
m (clarify) |
(AC input safety hack) |
||
| Line 8: | Line 8: | ||
These regulators all used switching techniques (likely one of the earliest [[switching power supply]] designs); they differed from later switching supplies (which generally dispense entirely with a large [[transformer]] on the [[alternating current|AC]] input, in that they take as input 30V AC supplied by the 'mother' system using a large (and heavy!) isolation/step-down transformer. | These regulators all used switching techniques (likely one of the earliest [[switching power supply]] designs); they differed from later switching supplies (which generally dispense entirely with a large [[transformer]] on the [[alternating current|AC]] input, in that they take as input 30V AC supplied by the 'mother' system using a large (and heavy!) isolation/step-down transformer. | ||
| + | |||
| + | Pins 6, 7 and 8 of the common connector (below) are used for the AC input, but each of the three uses a different pair of pins, with the third left un-connected; thus, if one is plugged into the wrong connector on the [[power harness]], no harm results. | ||
The [[7014251 +12VB and +5VB Battery Backup Regulator]], used with the [[H775D Battery Backup Unit]], is another in the series. | The [[7014251 +12VB and +5VB Battery Backup Regulator]], used with the [[H775D Battery Backup Unit]], is another in the series. | ||
| Line 13: | Line 15: | ||
==Connectors== | ==Connectors== | ||
| − | All use a common connector (which carries both input and output [[conductor]]s), an 8-pin 'Commercial MATE-N-LOK', made by AMP. The | + | All use a common connector (which carries both input and output [[conductor]]s), an 8-pin 'Commercial MATE-N-LOK', made by AMP. The power harness uses a female shell (housing) with male pins; the regulators use a male shell with female sockets (pins). |
The female shell is AMP part # 1-480460-0, pin part # 60620-1; the male shell is part # 1-480459-0, pin part # 60619-1. (There are a large number of different pin options: 30-22, 24-18, and 20-14 gauge; tin and gold plated; and brass and phosphor-bronze material. The part numbers given are for tinned brass, 20-14 gauge.) | The female shell is AMP part # 1-480460-0, pin part # 60620-1; the male shell is part # 1-480459-0, pin part # 60619-1. (There are a large number of different pin options: 30-22, 24-18, and 20-14 gauge; tin and gold plated; and brass and phosphor-bronze material. The part numbers given are for tinned brass, 20-14 gauge.) | ||
Revision as of 15:31, 21 September 2018
The DEC standard modular regulators (not a formal DEC term) were a series of modular power supply units, used primarily in the H742 Power Supply of the BA11-F Mounting Box and the H765 Power System of the BA11-K mounting box. (They are also occasionally found in other locations.)
Supported regulators include:
- H744 +5V Regulator (and later versions, H7440 and H7441)
- H745 -15V Regulator
- H754 +20V, -5V Regulator
These regulators all used switching techniques (likely one of the earliest switching power supply designs); they differed from later switching supplies (which generally dispense entirely with a large transformer on the AC input, in that they take as input 30V AC supplied by the 'mother' system using a large (and heavy!) isolation/step-down transformer.
Pins 6, 7 and 8 of the common connector (below) are used for the AC input, but each of the three uses a different pair of pins, with the third left un-connected; thus, if one is plugged into the wrong connector on the power harness, no harm results.
The 7014251 +12VB and +5VB Battery Backup Regulator, used with the H775D Battery Backup Unit, is another in the series.
Connectors
All use a common connector (which carries both input and output conductors), an 8-pin 'Commercial MATE-N-LOK', made by AMP. The power harness uses a female shell (housing) with male pins; the regulators use a male shell with female sockets (pins).
The female shell is AMP part # 1-480460-0, pin part # 60620-1; the male shell is part # 1-480459-0, pin part # 60619-1. (There are a large number of different pin options: 30-22, 24-18, and 20-14 gauge; tin and gold plated; and brass and phosphor-bronze material. The part numbers given are for tinned brass, 20-14 gauge.)
The Commercial MATE-N-LOK line is now made by TE Connectivity, who bought AMP. Unfortunately, they have ceased production on these two shells (although the pins are still being made). Some vendors still have stocks, though; as of July, 2018, ConnectorPeople and Quest still had some in stock.
