VAX-11/750 & VAX-11/751 Revision Control
From Computer History Wiki
_ K-RM-1175X Rev A, VAX 11/750 & 11/751 Revision Control Document, Nov 1990 11/750 AND 11/751 REVISION CONTROL DOCUMENT ------------------------------------------- ========================================================= | CHANGES IN THIS UPDATE | | | | WILL BE NOTED BY AN " ** " IN THE LEFT MARGIN | ========================================================= TABLE OF CONTENTS ----------------- Page 1.0 INTRODUCTION................................. 1 ** 1.1 11/750 System Chart ** 1.2 11/750 Revision Summary Chart 2.0 REVISION CRITERIA............................ 7 3.0 11/750 KERNEL REVISION CONTROL............... 7 3.1 Kernel Identification Register Hardware Rev Level 3.2 SID Register H/W Rev Problem 3.3 Microcode Revision History 3.4 Module Revision History 4.0 MODULE REVISION HISTORY...................... 10 5.0 11/750 KERNEL REVISION HISTORY............... 11 5.1 Module Revision Charts - 11/750 Kernel 5.2 11/750-50 Kernel Revision Summary (VAX750-R-0005) 5.3 11/750-58 Kernel Revision Summary " 5.4 11/750-60 Kernel Revision Summary (VAX750-R-0006) 5.5 11/750-68 Kernel Revision Summary " 5.6 11/750-70 Kernel Revision Summary (VAX750-R-0007) 5.7 11/750-78 Kernel Revision Summary " 5.8 11/750-7C Kernel Revision Summary " 5.9 11/750-80/88/8C Kernel Revision Summary (11750-8-I008) 5.10 11/750-90/98/9C Kernel Revision Summary (11750-9-I009) 6.0 OPTION REVISION HISTORY.......................27 6.1 RH750 - Massbus Adapter 6.2 FP750 - Floating Point 6.3 KU750 - User WCS 6.4 DW750 - Second Unibus 6.5 DR750 - General Purpose Interface 6.6 KC750 - Remote Diagnosis 6.7 CI750 - Computer Interconnect - 11/750 Date: NOV 8, 1990 Updates: Rose Murphy CSSE 1.0 INTRODUCTION This document is intended to define the revision history of the VAX 11/750 system for purposes of identifying the compatible hardware, diagnostics, firmware, and operating system software. (All references to the 11/750 apply to the 11/751 as well, unless otherwise noted.) NOTE: All references to Rev. 00-04 have been deleted. It is assumed all field machines are at minimum Rev 5. This document will be updated on a quarterly basis and released to microfiche in the VAX Library Update and the Speed Bulletin. The following VAX LIBRARY CARDS will be required as reference to the revision control plan. This document will state the source of information necessary for understanding firmware, diagnostic, and system software compatibility. INITIAL STARTING DOCUMENTATION DOCUMENT DESCRIPTION ---------------------------------------------------------------------- ZZ-EVNDX-W.0 VAX Diagnostic Index ZZ-ECOAB-1.0 VAX 11/750 Control Store Microcode Listing CMT050 ZZ-ECOAD-1.0 VAX 11/750 Boot Rom Listing TU58 RK07 RL02 ---------------------------------------------------------------------- 1.1 11/750 COMPATIBILITY CHART -------------------------- The following chart summarizes the compatible hardware, software, microcode and diagnostic revision levels for each system revision. For information concerning the corresponding module revisions for the kernel and option modules, see sections 5.1 and 6. The system revision reflects the rev of the overall 11/750 system. Only an increase to the kernel rev will increment the system revision; thus, the kernel revision and system revision will always be the same. The implementation of the SID switch reverses the bit positions of the SID register to be able to read the 11/750 hardware revision as well as the backplane revision. (See Section 3.0 and 3.1). (Refer to Option Revision sections for module revision information.) ---------------------------------------------------------------------- 11750 SYSTEM REV SID| 50/58 | 60/68 | 70/78/7C |80/88/8C |90/98/9C ---------------------------------------------------------------------- KERNEL | 50/58 | 60/68 |70/78/7C |80/88/8C |90/98/9C ------------------------------------------------------------------- RH750 | 01 | 01 | 01 | 01 | 01 FP750 | 01,02 | 01,02 | 02 | 02 | 02 KU750 | 01 | 01 | 01 | 01 | 01,02 DR750 | 01 | 01 | 01 | 01 | 01 DW750 | 01,02 | 01,02 | 02 | 02 | 02 KC750 | 01 | 01 | 01-C* | 01-C* |01-C* CI750 | B1-E1 | B1-E1 | B1-F1 |B1-F1 |B1-H3 ---------------------------------------------------------------------- EVNDX (Minumum) | 12,18 | 15,18 |15,18, |15,18, | 34 ---------------------------------------------------------------------- ** VMS RELEASE | 3.X,4.X | 3.X,4.X |3.X,4.X, |3.X,4.X, |5.X ---------------------------------------------------------------------- ** CPU MICROCODE | 096,097 | 098 | 098,099 |098,099 |103 ---------------------------------------------------------------------- Notes: ------ o VMS V 4.0 will require minimum hardware Rev 50/58 (i.e. L0008) and minimum ucode Rev 98 FOR CI750 SYSTEMS with no UDA50s. o 11/750 systems with UDA50s and CIs must be at Rev 7 prior to VMS V4.0 upgrades and UDA50 must be at Rev 5. o UDA50A Rev 5 refers to ucode Version 5. o Minimum rev for CI750 is B1. It is recommended that all CI750s be upgraded to the current rev. * "C" = new convention for tracking options. See below for further explanation. Old Rev "00" =A "01" =B 11750 CPU with a CI750 must have 4MB of physical memory. o CMT103 is required for VMS V5.0. 1.2 11/750 REVISION SUMMARY CHART ----------------------------- Hardware changes noted under each system revision reflect changes to the kernel for each system revision. New system ID info also noted. VMS and microcode revision are noted for compatibility purposes. The revisions are minimum revisions. =============================================================================== 11750 SYSTEM REV 50 58 =============================================================================== Hardware: -------- L0003 E=C;CS=C2;MR=F E=C;CS=C2;MR=F E=D;CS=F;MR=F E=D;CS=F;MR=F 11/750 QC=E103 is DC651 QC=E103 is DC651 KERNEL DC651 DC651 ----------------------------------------------------------------------- L0004 E=D;CS=J1;MR=K E=D;CS=J1;MR=K E=E;CS=K;MR=K E=E;CS=K;MR=K QC=E135 is QC=E135 is 23-991A9 23-991A9 ----------------------------------------------------------------------- L0008-YA E=B;PR=A1 E=B;PR=A1 ----------------------------------------------------------------------- L0008-YB E=B;PR=C2 E=B;PR=C2 ----------------------------------------------------------------------- L0016 E=B;CS=B QC=Wire from E7-15 to E8-11 ----------------------------------------------------------------------- 70-16486 WL=B WL=C Bkpnl ------------------------------------------------------------------------------- DW750 L0010 E=C;PR=C1 E=C;PR=C1 QC=E50 is 23-991A9 QC=E50 is 23-991A9 ------------------------------------------------------------------------------- KC750 L0006 E=A;CS=*3 E=A;CS=*3 E=B;CS=B1 E=B;CS=B1 E=C;CS=D E=C;CS=D QC=Wires on E6-3,4 QC=Wires on E6-3,4 ------------------------------------------------------------------------------- VMS REL: 3.X,4.X 3.X,4.X ------------------------------------------------------------------------------- MICROCODE: CMT096/CMT097 CMT096/CMT097 ------------------------------------------------------------------------------- SYSTEM ID: Rev B Bkpl 02006050/02006150 ------------------------------------------------------------------------------ Rev C Bkpl 02006058/02006158 ------------------------------------------------------------------------------ Rev D bkpl Key: --- E = Etch Rev CS = Circuit Schematic Rev MR = Module Rev * PR = Part Rev QC = Quick Check WL = Wire List Rev * See Section 4.0 - Module Revision History - for explanation =============================================================================== 11750 SYSTEM REV 60 68 =============================================================================== Hardware: --------- L0003 E=C;PR=H1 E=C;PR=H1 11/750 E=D;PR=H2 E=D;PR=H2 Kernel QC=E4 is QC=E4 is 74S00 74S00 ---------------------------------------------------------------------- L0003-YA E=E1;PR=C1 E=E1;PR=C1 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 ---------------------------------------------------------------------- L0004 E=D;PR=L1 E=D;PR=L1 E=E;PR=L2 E=E;PR=L2 QC=Jmpr between QC=Jmpr between E46 1 & 2 E46 1 & 2 ---------------------------------------------------------------------- 70-16486 WL=B WL=C Bkpnl ----------------------------------------------------------------------------- DW750 L0010 E=C;PR=E1 E=C;PR=E1 QC for E1 QC for E1 - Jumper - Jumper between E56.11 between E56.11 & E24.5 & E24 QC for F1 QC for F1 - Ram @ E55 - Ram @ E55 is 9122 is 9122 ----------------------------------------------------------------------------- FP750 L0001 E=D;PR=E2 E=D;PR=E2 E=E;PR=E1 E=E;PR=E1 QC=R33 is 75 QC=R33 is 75 OHM resistor OHM resistor ----------------------------------------------------------------------------- **VMS REL: 3.X,4.X 3.X,4.X ----------------------------------------------------------------------------- **MICROCODE: CMT098/CMT099 CMT098/CMT099 ----------------------------------------------------------------------------- SYSTEM ID: Rev B Bkpl 02006260 ---------------------------------------------------------------------------- Rev C Bkpl 02006268 ---------------------------------------------------------------------------- Key: --- E = Etch Rev PR = Part Rev QC = Quick Check NOTE: The above system revisions were cancelled. =============================================================================== 11750 SYSTEM REV 70 78 7C =============================================================================== Hardware: --------- L0003 E=C;PR=J1,K1 E=C;PR=J1,K1 E=C;PR=J1,K1 11/750 E=D;PR=J2,K2,K3 E=D;PR=J2,K2,K3 E=D;pr=J2,K2,K3 Kernel QC=E109 pins QC=E109 pins QC=E109 pins 4,5,6 grounded 4,5,6 grounded 4,5,6 grounded ---------------------------------------------------------------------- L0003-YA E=E1;PR=C1 E=E1;PR=C1 E=E1, PR=C1 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 ---------------------------------------------------------------------- L0004 E=D;PR=M1,N1, E=D;PR=M1,N1, E=D;PR=M1,N1, E=E;PR=M2,N2, E=E;PR=M2,N2, E=E;PR=M2,N2, QC=E11 is QC=E11 is QC=E11 is 23-656A2-00 23-656A2-00 23-656A2-00 ---------------------------------------------------------------------- 70-16486 WL=B WL=C WL=D Bkpnl ----------------------------------------------------------------------------- DW750 L0010 E=C;PR=E1 E=C;PR=E1 E=C;PR=E1 QC for E1 QC for E1 QC for E1 - Jumper - Jumper - Jumper between E56.11 between E56 between E56 & E24.5 & E24.5 & E24.5 ----------------------------------------------------------------------------- ** VMS REL: 3.X,4.X, 3.X,4.X 3.X, 4.X ----------------------------------------------------------------------------- ** MICROCODE: CMT098-CMT99 CMT098-CMT99 CMT098/CMT99 ----------------------------------------------------------------------------- SYSTEM ID: Rev B Bkpl 02006270 ---------------------------------------------------------------------------- Rev C Bkpl 02006278 ---------------------------------------------------------------------------- Rev D Bkpl 0200637C Key: --- E = Etch Rev PR = Part Rev QC = Quick Check =============================================================================== 11750 SYSTEM REV 80 88 8C =============================================================================== Hardware: --------- L0003 E=C;PR=J1,K1 E=C;PR=J1,K1 E=C;PR=J1,K1 11/750 E=D;PR=J2,K2,K3 E=D;PR=J2,K2,K3 E=D;pr=J2,K2,K3 Kernel QC=E109 pins QC=E109 pins QC=E109 pins 4,5,6 grounded 4,5,6 grounded 4,5,6 grounded ---------------------------------------------------------------------- L0003-YA E=E1;PR=C1 E=E1;PR=C1 E=E1, PR=C1 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 ---------------------------------------------------------------------- L0004 E=D;PR=M1,N1, E=D;PR=M1,N1, E=D;PR=M1,N1, E=E;PR=M2,N2, E=E;PR=M2,N2, E=E;PR=M2,N2, QC=E11 is QC=E11 is QC=E11 is 23-656A2-00 23-656A2-00 23-656A2-00 ---------------------------------------------------------------------- 70-16486 WL=B WL=C WL=D Bkpnl ----------------------------------------------------------------------------- DW750 L0010 E=C;PR=E1 E=C;PR=E1 E=C;PR=E1 QC for E1 QC for E1 QC for E1 - Jumper - Jumper - Jumper between E56.11 between E56 between E56 & E24.5 & E24.5 & E24.5 ----------------------------------------------------------------------------- ** VMS REL: 3.X,4.X 3.X,4.X 3.X, 4.X ----------------------------------------------------------------------------- ** MICROCODE: CMT098-CMT99 CMT098-CMT99 CMT098/CMT99 ----------------------------------------------------------------------------- SYSTEM ID: Rev B Bkpl 02006280 ---------------------------------------------------------------------------- Rev C Bkpl 02006288 ---------------------------------------------------------------------------- Rev D Bkpl 0200638c Key: --- E = Etch Rev PR = Part Rev QC = Quick Check =============================================================================== 11750 SYSTEM REV 90 98 9C =============================================================================== Hardware: --------- L0003 E=C;PR=J1,K1 E=C;PR=J1,K1 E=C;PR=J1,K1 11/750 E=D;PR=J2,K2,K3 E=D;PR=J2,K2,K3 E=D;pr=J2,K2,K3 Kernel QC=E109 pins QC=E109 pins QC=E109 pins 4,5,6 grounded 4,5,6 grounded 4,5,6 grounded ---------------------------------------------------------------------- L0003-YA E=E1;PR=C1 E=E1;PR=C1 E=E1, PR=C1 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 QC=ETCH #50-13693-01 ---------------------------------------------------------------------- L0004 E=D;PR=M1,N1, E=D;PR=M1,N1, E=D;PR=M1,N1, E=E;PR=M2,N2, E=E;PR=M2,N2, E=E;PR=M2,N2, QC=E11 is QC=E11 is QC=E11 is 23-656A2-00 23-656A2-00 23-656A2-00 ---------------------------------------------------------------------- 70-16486 WL=B WL=C WL=D Bkpnl ----------------------------------------------------------------------------- DW750 L0010 E=C;PR=E1 E=C;PR=E1 E=C;PR=E1 QC for E1 QC for E1 QC for E1 - Jumper - Jumper - Jumper between E56.11 between E56 between E56 & E24.5 & E24.5 & E24.5 ----------------------------------------------------------------------------- VMS REL: 5.0 5.0 5.0 ----------------------------------------------------------------------------- MICROCODE: CMT103 CMT103 CMT103 ----------------------------------------------------------------------------- SYSTEM ID: Rev B Bkpl 02006290 ---------------------------------------------------------------------------- Rev C Bkpl 02006298 ---------------------------------------------------------------------------- Rev D Bkpl 0200639C Key: --- E = Etch Rev PR = Part Rev QC = Quick Check 2.0 REVISION CRITERIA Architectural or functional changes in the system must cause a change of the kernel revision level. This includes changes to the hardware that change performance or operation of the system that is detectable to the diagnostics and operating system software. Modifications to cables, power subsystems, ventilation equipment, or mechanical design should not cause a change to the kernal revision level. The VAX 11/750 revision history for a particular subsystem or option will be desig- nated as follows... OPTION-XXN where, OPTION is the five letter neumonic (i.e. KA750), XX is a fun- tional change description code (i.e 01), and N is a non-functional change to the option. Non-functional changes to an option include relayout of modules to eliminate rework wires or changes to document- ation that do not affect operation of the system. Changes to purchase part numbers at the module level should not cause the hardware revision to be raised either. Functional changes to any of the modules in the kernel subsystem (i.e. KA750 CPU and MS750) increments each module revision, as well as the kernel revision. A switch pack and pull up resistor assembly has been designed and was installed in all Rev "C" backplanes shipped from manufacturing: in 11/750 CPUs, beginning with Serial No. BTO3096, and 11/751 CPUs, beginning with Serial No. BTO215. The switch pack will be set by manufacturing before it is shipped. Switch pack settings will change as a result of a kernel revision change to the 11/750 CPU. This will be done by an ECO. 3.0 VAX 11/750 KERNEL REVISION CONTROL The VAX 11/750 processor has a system identification register (SID) register similiar to the VAX 11/780 processor; however, there are two basic differences between the VAX 11/750 and VAX 11/780 processor SID registers. These are... * VAX 11/750 SID does NOT contain the system serial number * VAX 11/750 SID DOES contain a field describing current control store microcode revision. This is because VAX 11/750 does not have the FPLA to intercept ECO'd microcode locations. The figure 2-1 illustrates the format of the VAX 11/750 system identification register (SID). This register is accessible to macro code and the console terminal through IPR address ^X3E. Examination of the register shows 4 bytes, 3 of which are functional. The high byte is the processor type code byte used by the diagnostics and operating system to decide which type of processor the software is operating on. Known type codes are listed below. TYPE CODE BYTE PROCESSOR 00000000 undefined 00000001 VAX 11/780 00000010 VAX 11/750 00000011 VAX 11/730 Byte 2 of the SID register is always zero. Byte 1 of the SID register is the microcode revision of the control store. This number is generated by the microprogrammer in the REV750.MIC file of the microcode listing ECOAB. There is a MICRO2 assembler directive called .SET/MICROREV=version at the top of the page which is upgraded for each major assembly of the the microcode. In the MFPR microinstruction flows this equated value is substituted into the short literal field of the microinstruction and becomes the microcode revision that appears in byte 1 of the SID register. The number following MICROREV is DECIMAL. You must convert the hex byte to decimal after examining the SID register. Byte 0 of the SID register is the hardware revision of the kernal and the backplane rev. Both of these revisions are programmable on the CPU backplane via the Kernal Revision Level Input Device. (See section 3.1 for more detailed information.) There is a 74LS244 tri-state driver on the UBI module that interfaces to the CPU WBUS. The MFPR microinstruction flows read this byte when referencing the SID register. The number in byte 0 of the SID register is a BINARY revision level programmed on the SID input device. SID REGISTER FORMAT IPR ADDRESS ^X3E +----------------+---------------+---------------+---------------+ | | | | | | 00000010 | 00000000 | 00110010 | 00000000 | | | | | | +----------------+---------------+---------------+---------------+ TYPE CODE = 2 MUST BE 0 MICROCODE REV HARDWARE REV (Byte 3) (Byte 2) (Byte 1) (Byte 0) Figure 2-1 NOTE: This example shows the type code as 2 (VAX 11/750), Microcode rev- ---- ision is 32 hex or 50 decimal, and the hardware revision level is equal to zero zero. 3.1 Kernel Identification Register Hardware Revision Level Input Device The Kernel ID Register switch pack and pull-up assembly attaches across slots 3 and 4 section B of the backplane. Backplane pins will protrude through the PC board and pins used will have a female socket that is easily grasped with a scope probe. The following diagrams show what the switch pack actually looks like; the section containing the bits that must be set is depicted in a larger scale at the right. +----------------+ REG BIT POSITION | SYS ID | 7 6 5 4 3 2 1 0 <- ETCHED ON BOARD +-| 76543210 | O +------------------------+ | -A +--------+ | F | 1 2 3 4 5 6 7 8 |<- SWITCH NUMBER | -C |12345678| | F |------------------------| STAMPED ON | -E |||||||||| | || || || || || || || || || SWITCH-PAK | - +--------+ | || || || || || || || || || | - 5415142 | || || || || || || || || || | - 5015141A | +------------------------+ | - +--------+ | | - |DIGITAL | | | - +--------+ | OFF = 1 | - +---------+ | | UU |RES PAK | | +-| +---------+ | | SIDE 1 | +----------------+ Bits 7 - 4 (1 - 4) represent the Kernal Rev; bits 3 - 0 (5 - 8) represent the backplane Rev. Backplane rev - 0 = Rev B; 8 - Rev C. NOTE THAT ONLY REV C BACKPLANES WILL SUPPORT 64K MEMORY. Example for Revision 50 (Kernal Rev 5; Backplane Rev B) REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||N||F||N||N||N||N|| || ||F|| ||F|| || || || || +------------------------+ (OFF = 1) Example of Revision 58 (Kernal Rev 5; Backplane Rev C) REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||N||F||F||N||N||N|| || ||F|| ||F||F|| || || || +------------------------+ (OFF = 1) All Rev "B" backplanes in the field will have the switch installed via FCO. This device is included in the VAX 11/750 Rev 7 FCO kits - EQ-01201-01 and EQ-01201-02. Instructions on how to install and set the switch are included in the Rev 7 FCO document. The parts can also be obtained by ordering the following parts: 54-15142 SID Switch 12-16821-00 Backplane Housing Connector 3.2 SID Register Hardware Revision Problem The current design of the SID register hardware revision byte 0, has an 8 bit 74LS244 tri-state driver chip interfaced to the backplane. The chip inputs are not inverted in the driver and are not pulled up either. so the resultant data with SID register byte 0 not programmed is FF. Since the inputs just "floats" at times the output may not always be FF. This is a problem when running the DIAGNOSTIC SUPERVISOR. The super- visor "forgets" where it came from and the program data must be enter- ed manually to get the supervisor to "remember" where it came from. This is time consuming, especially if the field engineer must power the machine up and down to replace modules. The result is the MTTR is ex- tended to repair the machine. The register must be wired HI or LO, but wiring the bits HI is another problem. The CPU power supply must be connected to the chip inputs directly. If the 74LS244 fails by shorting the input pin to ground, hopefully the chip will burn open, but if not, other damage could result. There should be a pulled up +5V through a 1K resistor to several unused backplane pins. 3.3 Microcode Revision History A comprehensive revision history of VAX 11/750 microcode is contained in the microcode listing in the VAX LIBRARY fiche set (ECOAB 3.0). Revision W of the VAX LIBRARY contains the microcode listing for control store version CMT050. Since there have been numerous changes to the microcode since version CMT050, it is suggested that you read the microcode revision history contained in the REV750.MIC file of the microcode listing. Changes to the VAX 11/750 microcode AFTER CMT062 will be described briefly in this document and what the symptoms and corrective actions were. CMT098 will be available in release 19 as ECOAB98.0 on microfiche. 4.0 MODULE REVISION HISTORY Modules are marked in one of three ways: CS (Circuit Schematic) Revision, MR (Module Revision) or PR (Part Revision). DEC Standard 012 institutes Part Revision and is being implemented on all 11/750 modules. All new modules will use Part Revision. Part Revision always consists of a letter and a number, i.e. A1 or A2. The letter is increased for a functional change; the number is incremented for a non-functional change. Part Revision will be implemented on existing 11/750 modules, as ECOs occur, by using the current CS revision. CS Rev "D" becomes Part Rev "D1" for a non-functional change; for a functional change, the Part Rev would be "E1". The revision is noted on each module by either a brady marker or a red stamp on the tab of the module handle. If both are present, the brady marker should represent the latest revision. (It is wise to do a quick check, if possible, to insure that this is correct!) Compatible revisions for each part (unit) are separated by commas; also, revisions separated by a dash, i.e. A1-C2, means that those revisions, plus whatever is in between, are compatible. Any special requirements (specific revisions for certain configurations, etc.) will be noted in the revision summary section. Revisions noted are all minimum revisions. 5.0 11/750 KERNEL REVISION HISTORY ------------------------------ Listed below is the revision history of the 11/750 kernel, indicating the compatible module and/or subsystem revisions for each hardware revision. Equivalent module revisions are separated by commas. The 11/750 kernel consists of the KA750 CPU and the MS750 (AA and CA). ---------------------------------------------------------------------- KA750 - 70-16486 CPU Backplane Asembly L0002 DPM Module L0003 MIC Module or * L0003-YA MIC Module L0004 UBI Module ** L0005 CCS Module L0008-YA PCS Module (Non-User WCS) -or- L0008-YB PCS Module (User WCS) TU58-XA Tape Drive Unit 54-13489 TU58 Tape Controller Unit M9313 UET Unibus Terminator/ Exerciser MS750-AA L0011 CMC Module M8728 256KB array board MS750-CA L0016 Controller M8750 1MB array board MS750-HB L0022 Controller M7199 4 MB array board -------------------------------------------------------------------- * The kernel will also contain EITHER an L0003 or a L0003-YA module--not both! The L0003-YA was introduced as a Cost Reduced module with TB and Cache Address Termination. ** Note that the kernel contains EITHER an L0005 OR an L0008 - not both!!!! All L0005s in the field were replaced with L0008s as part of FCO VAX11/750-R-0005. This history has been separated into three charts: Chart 1 - Rev "B" backplane - SID Switch Setting = xxxxxxx0 Chart 2 - Rev "C" backplane - SID Switch Setting = xxxxxxx8 Chart 3 - Rev "D" backplane - SID Switch Setting = xxxxxxxC **NOTE: All revisions below Revision 5X have been removed from this document. This is because all systems should be at a minimum of revision 5. Older system revisions are no longer supported. KA750-A REVISION SUMMARY ------------------------ o This is the first introduction of rev control for the KA750. Up to this point, revisions were tracked at the Kernel level only. o This revision implements ECO L0004-MKO10 and fixes two problems with the UBI: 1 - UBI looses device interrupts. 2 - When the UBI is the Bus Master, it deasserts BBSY at the same time as MSYN L, allowing no deskew time for the address and control lines. o FCO KA750-A-I-001 was made available to those customers who experienced either of the above two problems. Not all systems require the fix. 5.1 Kernel Module Revision Charts Charts 1, 2 and 3 list the corresponding Etch, Circuit Schematic, Module Revision and Part Revisions. CHART 1 ------------------------------------------------------------------------------| 11/750 REV | 50 | 60 | 70 | 70 | 80 | | ==============================================================================| KA750 | | | | A | A | | ----------------------------------------------------------------------|-------| MODULE | SLOT | ETCH | | | | | | | ----------------------------------------------------------------------|-------| L0002 | 2 | C |CS=C,C1 |CS=C,C1 |CS=C,C1 |CS=C,C1 | | | | | |MR=C,D |MR=C,D |MR=C,D |MR=C,D |MR=C,D | | | | D |CS=D,E |CS=D,E |CS=D,E | CS=D,E | CS=D,E | | | | |MR=D,E |MR=D,E |MR=D,E |MR=D,E-E2|MR=D,E-E2| | ------------------------------------------------------------------------------| L0003 | 3 | C |PR=H1 |PR=J1,K1|PR=J1,K1 |PR=J1,K1| | | | | |MR=F | | | | | | | | D |CS=F |PR=H2 |PR=J2,K2,|PR=J2,K2|PR=J2,K2 | | | | |MR=F | | K3 | K3 | K3 | | ----------------------------------------------------------------------|-------| L0003-YA| 3 | | | | |PR=C1 |PR=C1 | | ----------------------------------------------------------------------|-------| L0004 | 4 | D |CS=J1 |PR=L1 |PR=M1,N1 |PR=P1 |PR=P1 | | | | |MR=K | | | | | | | | E |CS=K |PR=L2 |PR=M2,N2 |PR=P2 |PR=P2 | | | | |MR=K | | | | | | ----------------------------------------------------------------------|-------| L0005 | 5 | D |N/A |N/A | N/A | N/A | N/A | | | | |N/A |N/A | N/A | | | | ----------------------------------------------------------------------|-------| L0008-YA| 5 | B |PR=A1-B2|PR=A1-B2|PR=A1-B2 |PR=A1-B2|PR=A1-B2 | | ----------------------------------------------------------------------|-------| | L0008-YB| 5 | B |PR=C2 |PR=D2 | PR=D2 | PR=D2 |PR=D2 | | ----------------------------------------------------------------------|-------| M9313 |28 A-B| B |CS=A |CS=A | CS=A | CS=A |CS=A | | | | |MR=A,B |MR=A,B |MR=A,B |MR=A,B |MR=A,B | | ----------------------------------------------------------------------|-------| TU58-XA | | |F-K | F-K | F-K | F-K | F-K | | ----------------------------------------------------------------------|-------| TU58-XB | | E | F1-F4 | F1-F4 | F1-F4 |F1-F4 |F1-F4 | | (54-13489)| | F | H-L1 | H-L1 | H-L1 |H-L1 |H-LI | | ----------------------------------------------------------------------|-------| CONTROL | | C | CS=C | CS=C | CS=C |CS=C | CS=C | | PANEL | | |MR=C,D |MR=C,D | MR=C,D |MR=C,D | MR=C,D | | (54-13795)| | | | | | | | | ----------------------------------------------------------------------|-------| BACKPNL | | | WL=B | WL=B | WL=B | WL=B |WL=B | | (70-16486)| | | | | | | | | ----------------------------------------------------------------------------- | MS750-AA | | A1 | A1 | A1 | A1 |A1 | | ==============================================================================| L0011 | 10 | C | CS=D | CS=D | CS=D | CS=D |PR=E1 | | ------------------------------------------------------------------------------| M8728 | 11-18| C | CS=C | CS=C | CS=C | CS=C |CS=C | | ----------------------------------------------------------------------+-------| Key: E = Etch Rev; CS = Circuit Schematic Rev; MR = Module Rev; --- PR= Part Rev; WL = Wirelist Rev CHART 2 ------------------------------------------------------------------------------| 11/750 REV | 58 | 68 | 78 | 78 | 88 | ==============================================================================| KA750 | | | | A | A | ------------------------------------------------------------------------------| MODULE | SLOT | ETCH | | | | | | ------------------------------------------------------------------------------| L0002 | 2 | C |CS=C,C1 |CS=C,C1 |CS=C,C1 |CS=C, C1 | | | | | |MR=C,D |MR=C,D |MR=C,D |MR=C,D |MR=C,D | | | | D |CS=D,E |CS=D,E |CS=D,E | CS=D,E |CS=D,E | | | | |MR=D,E |MR=D,E |MR=D,E |MR=D,E-E2|MR=D,E=E2| | ------------------------------------------------------------------------------| L0003 | 3 | C |PR=H1 |PR=J1,K1|PR=J1,K1 |PR=J,K1 | | | | | |MR=F | | | | | | | | D |CS=F |PR=H2 |PR=J2,K2,|PR=J2,K2 |PR=J2,K2 | | | | |MR=F | | K3 | K3 | K3 | | ------------------------------------------------------------------------------| L0003-YA| 3 | | | | |PR=C1 |PR=C1 | | ------------------------------------------------------------------------------| L0004 | 4 | D |CS=J1 |PR=L1 |PR=M1,N1 |PR=P1 |PR=P1 | | | | |MR=K | | | | | | | | E |CS=K |PR=L2 |PR=M2,N2 |PR=P2 |PR=P2 | | | | |MR=K | | | | | | ------------------------------------------------------------------------------| L0005 | 5 | D |N/A |N/A | N/A | N/A |N/A | | | | |N/A |N/A | N/A | | | | -------------------------------------------------------------|----------------| L0008-YA| 5 | B |PR=A1-B2|PR=A1-B2|PR=A1-B2 |PR=A1-B2 |PR=A1-B2 | | ------------------------------------------------------------------------------| L0008-YB| 5 | B |PR=C2 |PR=D2 | PR=D2 | PR=D2 |PR=D2 | | ------------------------------------------------------------------------------| M9313 |28 A-B| B |CS=A |CS=A | CS=A | CS=A |CS=A | | | | |MR=A,B | | | | | | ------------------------------------------------------------------------------| TU58-XA | | |F-K | F-K | F-K | F-K | | | ------------------------------------------------------------------------------| TU58-XB | | E | F1-F4 | F1-F4 | F1-F4 |F1-F4 |F1-F4 | | (54-13489)| | F | H-L1 | H-L1 | H-L1 |H-L1 | | | ------------------------------------------------------------------------------| CONTROL | | C | CS=C | CS=C | CS=C |CS=C |CS=C | | PANEL | | |MR=C,D |MR=C,D | MR=C,D |MR=C,D |MR=C,D | | (54-13795)| | | | | | | | | ------------------------------------------------------------------------------| BACKPNL | | | WL=C | WL=C | WL=C | WL=C |WL=C | | (70-16486)| | | | | | | | | ------------------------------------------------------------------------------| MS750-CA | | A1 | A1 | A1 | A1 | | | ==============================================================================| L0016 | 10 | B |CS= B,C | CS=B | CS=B | CS=B | PR=C1 | | ------------------------------------------------------------------------------| M8750 CS=A,B | CS=A,B | CS=A,B | CS=A,B | A,B | A,B | | ------------------------------------------------------------------------------| Key: E = Etch Rev; CS = Circuit Schematic Rev; MR = Module Rev; --- PR= Part Rev; WL = Wirelist Rev CHART 3 ------------------------------------------------------------------------------- 11/750 REV | 5C | 6C | 7C | 7C | 8C | | ==============================================================================| KA750 | | | | A | A | | -----------------------------------------------------------------------|------| MODULE | SLOT | ETCH | | | | | | | -----------------------------------------------------------------------|------| L0002 | 2 | C |CS=C,C1 |CS=C,C1 |CS=C,C1 |CS=C,C1 | | | | | |MR=C,D |MR=C,D |MR=C,D |MR=C,D |MR=C,D | | | | D |CS=D,E |CS=D,E |CS=D,E | CS=D,E | | | | | |MR=D,E |MR=D,E |MR=D,E |MR=D,E-E2| | | -----------------------------------------------------------------------|------| L0003 | 3 | C |PR=H1 |PR=J1,K1|PR=J1,K1 |PR=J1,K1 | | | | | |MR=F | | | | | | | | D |CS=F |PR=H2 |PR=J2,K2,|PR=J2,K2 | | | | | |MR=F | | K3 | K3 | | | -----------------------------------------------------------------------|------| L0003-YA| 3 | | | | |PR=C1 | PR=C1 | | -----------------------------------------------------------------------|------| L0004 | 4 | D |CS=J1 |PR=L1 |PR=M1,N1 |PR=P1 |PR=P1 | | | | |MR=K | | | | | | | | E |CS=K |PR=L2 |PR=M2,N2 |PR=P2 | | | | | |MR=K | | | | | | -----------------------------------------------------------------------|------| L0005 | 5 | D |N/A |N/A | N/A | N/A | N/A | | | | |N/A |N/A | N/A | | | | -----------------------------------------------------------------------|------| L0008-YA| 5 | B |PR=A1-B2|PR=A1-B2|PR=A1-B2 |PR=A1-B2 |PR=A1-B2 | | -----------------------------------------------------------------------|------| L0008-YB| 5 | B |PR=C2 |PR=D2 | PR=D2 | PR=D2 |PR=D2 | | -----------------------------------------------------------------------|------| M9313 |28 A-B| B |CS=A |CS=A | CS=A | CS=A | | | | | |MR=A,B | | | | | | -----------------------------------------------------------------------|------| TU58-XA | | |F-K | F-K | F-K | F-K |F-K | | -----------------------------------------------------------------------|------| TU58-XB | | E | F1-F4 | F1-F4 | F1-F4 |F1-F4 |F1-F4 | | (54-13489)| | F | H-L1 | H-L1 | H-L1 |H-L1 |H-L1 | | -----------------------------------------------------------------------|------| CONTROL | | C | CS=C | CS=C | CS=C |CS=C |CS=C | | PANEL | | |MR=C,D |MR=C,D | MR=C,D |MR=C,D |MR=C,D | | (54-13795)| | | | | | | | | -----------------------------------------------------------------------|------| BACKPNL | | | WL=D | WL=D | WL=D | WL=D |WL=D | | (70-16486)| | | | | | | | | -----------------------------------------------------------------------|------| MS750-HB | | A1 | A1 | A1 | A1 | A1 | | =======================================================================|======| L0022 | 10 | | | | | | B2 | | -----------------------------------------------------------------------|------| M7199 | | | | | | | | ------------------------------------------------------------------------------| Key: E = Etch Rev; CS = Circuit Schematic Rev; MR = Module Rev; --- PR= Part Rev; WL = Wirelist Rev 5.2 11/750-50 KERNEL REVISION SUMMARY --------------------------------- NOTE THAT REV 50/58 WAS CANCELLED IN Q4FY84, EXCEPT FOR REPLACEMENT OF THE L0005 CCS MODULE WITH THE L0008-YA OR -YB PCS MODULE. EQ KIT NUMBERS FOR THE L0008 MODULES REMAIN THE SAME. SYSTEMS THAT DO NOT CONTAIN AN L0008 SHOULD BE UPGRADED CONCURRENT WITH REV 70/78. (SEE SECTION 5.8) Following Rev 50/58 revision summaries are for historical info. o Creation date is August 1983 - mfg. implementation of Rev 50. o Note that the difference between 50 and 58 is the backplane rev and the memory - 50 contains the Rev "B" backplane and 16K memory (L0011 controller and M8728 arrays); 58 machines contain the Rev "C" backplane and 64K memory (L0016 controller and M8750 (or M8728 arrays). This will result in some differences, but most information for for Rev 5 applies to both 50 and 58 machines. The differences will be noted. o This FCO consists of the following ECOs: L0003-TW003 - See Section 5.8 L0003-TW004 - See Section 5.8 L0004-TW006 - On unaligned data transfers using the buffered data path, and Unibus address bits 0 and 1 are asserted the UBI microsequencer will branch to DATOB execution flows on a DATI. - Writes to the Unibus map that clear the valid bit when the UBI is asserting SSYN can cause SSYN to deassert before MSYN deasserts. - the contents of the Time of Year Offset Register are modified upon assertion of UBUS DCLO L. - The UBI can assert DBBZ in response to a CPU Unibus reference after entering purge microcode flows causing the system to hang. L0016-SH002 - The refresh logic does not always work correctly on power up with six or more M8750 arrays. 11750-TW005/ 11751-TW004 - Replace L0005 (Common Control Store) with L0008 (Patchable Control Store) o Manufacturing implementation for a COMPLETE Rev 5 11/750/11/751 system was July 1984. Field implementation for Rev 5 began in September 1983. o FCO DW750-R-0001 and FCO KC750-R-0001 should be implemented, if required, at the same time as Rev 5. (See Sections 6.4 and 6.6 of this document for more details on these FCOs.) o The L0008 (PCS) module requires PCS microcode that is on TU58 Tape #3, P/N BE-T538A-DE. This tape will be included in the L0008 E.Q. kits and must be used to load the PCS microcode in order to run the new microcode - Rev 96 or 97. If the L0008 is installed without this tape, the machine will work but will run Rev 94 microcode. Instructions on installing PCS are included in the FCO documentation and will be included with new systems shipped from manufacturing that contain the L0008 module. o Compatible revision levels . Microcode - CMT096 and CMT097 - replaces CMT094 . VAX/VMS - Compatible with 2.X, 3.X **Note** 11/750 systems running Version 2.X that have a battery backup option are known to have problems with warm restart once Rev 5 (i.e. the L0008 module) is installed. Plan is to fix this in a future release of PCS microcode. Until then, it is recommended that these systems not be upgraded with the FCO. . Diagnostics Minimum EVNDX for Rev 50/58 is 12 (May 1983). Minimum diagnostic revision levels for Rev 5 are: Diagnostic Min. Version Title ~~~~~~~~~~ ~~~~~~~~~~~~ ~~~~~ ECCBA 1.3 VAX 11750 UBI/DW750 DIAG ECKAL 3.2 * VAX 11750 CACHE/TB DIAG ECKAX 5.0 * VAX 11/750 CLUSTER EXER ECSAA 6.10B * VAX 11/750 DIAG SUPERVISOR EVKAB 2.8 VAX ARCHITECTURAL INSTR EVKAC 4.3 * VAX FLOATING POINT INST EVKAD 1.4 VAX COMPATIBILITY MODE INST EVKAE 1.7 VAX PRIVILEGED ARCHT INSTR o Product Dependencies CI750 requires Rev 5. o Quick Check Examine SID register in console mode Rev 50 >>> E/I 3E ------ I 0000003E 02005F50 (5F on power up - Rev 95 I 0000003E 02006050 (60 with Rev 96 ucode loaded) I 0000003E 02006150 (61 with Rev 97 ucode loaded) L0003 - E103 is DC651 L0004 - E135 is 23-991A9 L0016 - Wire from E7-15 to E8-11 Presence of L0008 in Slot 5 o SID Switch Setting REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||N||F||N||N||N||N|| || ||F|| ||F|| || || || || +------------------------+ (OFF = 1) 5.3 11/750-58 KERNEL REVISION SUMMARY --------------------------------- NOTE THAT REV 50/58 WAS CANCELLED IN Q4FY84, EXCEPT FOR REPLACEMENT OF THE L0005 CCS MODULE WITH THE L0008-YA OR -YB PCS MODULE. EQ KIT NUMBERS FOR THE L0008 MODULES REMAIN THE SAME. SYSTEMS THAT DO NOT CONTAIN AN L0008 SHOULD BE UPGRADED CONCURRENT WITH REV 70/78. (SEE SECTION 5.8) o Section 5.5 applies (through the Compatible Revision Levels) to 11/750-58 as well. o Compatible revision levels . Microcode - CMT096 replaces CMT094 . VAX/VMS - Compatible with 3.X . Diagnostics - Same as Section 5.9 o Quick Check Examine SID register in console mode >>> E/I 3E ------ I 0000003E 02005F58 (5F on power up - Rev 95) I 0000003E 02006058 (60 with Rev 96 ucode loaded) I 0000003E 02006158 (61 with Rev 97 ucode loaded) L0003 - E103 is DC651 L0004 - E135 is 23-991A9 L0016 - Wire from E7-15 to E8-11 Presence of L0008 in Slot 5 o SID Switch Setting - Rev 58 REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||N||F||F||N||N||N|| || ||F|| ||F||F|| || || || +------------------------+ (OFF = 1) 5.4 11/750-60 KERNEL REVISION SUMMARY --------------------------------- o REV 60/68 HAS BEEN CANCELLED. NO FCO WILL BE IMPLEMENTED. ALL L0003 REV H1/H2 MODULES WILL BE REPLACED WITH REV J1/J2 MODULES AS PART OF Rev 70/78; ALL L0004 REV L1/L2 WILL BE REPLACED WITH REV M1/M2 AS PART OF REV 70/78. A problem was discovered with the L0003 cache parity fix (Rev H1/H2). DO NOT USE L0003 REV H1/H2, AS POSSIBLE CORRUPTION OF CUSTOMER'S DATA CAN OCCUR. This is known to be a problem with CI750s and DR750s, but can potentially be a problem in an 11/750 or 11/751 without these options. o The major difference between Revision 60 and 68 is the backplane revisions - 60 = Rev B; 68 = Rev C. Most information applies to both 60 and 68 and will be outlined in this section. Differences for Rev 68 will be noted. o Manufacturing implementation for Rev 6 was March 5, 1984 - from Burlington and Galway (approximately 50% will be POM and ship directly to customers; the other 50% will ship to FA&T facilities); FA&T plants (Westminster, Kanata, Ayr) will begin shipping Rev 6 in April. (Note that manufacturing only ships Rev 68) o Field implementation of this FCO is expected to begin in Q4FY84.. o Depending on the revision status of the machine, there may be more ECOs to install than those listed below. The FCO document for Rev 6 contains instructions to upgrade machines from Rev 3, 4 and 5 to Rev 6. o This REV 6 FCO consists of the following ECOs: L0003-TW005 - Fixes phantom TB parity errors - Allows recovery for cache parity errors - Allows recover for soft TB parity errors New Part Revision marked on the module handle will be: Etch C - "H1"; Etch D - "H2" CMT098 microcode required along with L0003 hardware L0004-TW007 - Corrects lost device interrupt problem - Permits use of all vendor parts on QVL - Controls crystal voltage when toy battery isn't installed New Part Revision marked on the module handle will be: Etch D - "L1"; Etch E - "L2" o Compatible Revision Levels . Microcode - CMT098 (PN BE-T538C-ME) - Released from SDC March 5, 1984. Rev 98 microcode will be included with 11/750 and 11/751 CPUs shipped from Burlington through March, to insure that the current microcode is available at installation. Software boxes shipped from SDC may contain the old rev microcode; Rev 98 part number is BE-T538C-ME. ONLY REV 98 SHOULD BE USED!!! . VAX/VMS - Warm restart problems in systems running 2.X of VMS still exists - there are no plans to fix this problem in the near future. . Diagnostics Minimum EVNDX for Rev 60/68 was 15 (March 1984). Minimum diagnostic revision levels for Rev 6 are: Diagnostic Min. Version Title ~~~~~~~~~~ ~~~~~~~~~~~~ ~~~~~ ECCBA 1.3 VAX 11750 UBI/DW750 DIAG ECKAL 3.3 VAX 11750 CACHE/TB DIAG ECKAX 5.1 * VAX 11/750 CLUSTER EXER ECSAA 6.13 * VAX 11/750 DIAG SUPERVISOR EVKAB 3.0 * VAX ARCHITECTURAL INSTR EVKAC 5.0 * VAX FLOATING POINT INST EVKAD 2.0 * VAX COMPATIBILITY MODE INST EVKAE 2.0 * VAX PRIVILEGED ARCHT INSTR o Quick Check Examine SID register in console mode Rev 60 >>> E/I 3E ------ I 0000003E 02005F60 (5F on power up - Rev 95) I 0000003E 02006260 (62 with Rev 98 ucode loaded) L0003 - E4 is a 74S00 L0004 - Jumper between E46 Pin 1 and 2 o SID Switch Setting REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||F||N||N||N||N||N|| || ||F||F|| || || || || || +------------------------+ (OFF = 1) 5.5 11/750-68 KERNEL REVISION SUMMARY --------------------------------- o Rev 60/68 HAS BEEN CANCELLED. NO FCO WILL BE IMPLEMENTED. ALL L0003 REV H1/H2 MODULES WERE REPLACED WITH J1/J2 MODULES AS PART OF REV 70/78; ALL L0004 REV L1/L2 MODULES WERE REPLACED WITH REV M1/M2 MODULES AS PART OF REV 70/78. A problem was discovered with the L0003 cache parity fix (Rev H1/H2). DO NOT USE L0003 REV H1/H2, AS POSSIBLE CORRUPTION OF CUSTOMER'S DATA CAN OCCUR. This is known to be a problem with CI750s and DR750s, but can potentially be a problem in an 11/750 or 11/751 without these options. o Quick Check Examine SID register in console mode Rev 68 >>> E/I 3E ------ I 0000003E 02005F68 (5F on power up - Rev 95) I 0000003E 02006268 (62 with Rev 98 ucode loaded) L0003 - E4 is a 74S00 L0004 - Jumper between E46 Pin 1 and 2 o SID Switch Setting REG BIT POSITION 7 6 5 4 3 2 1 0 <--ETCHED ON BOARD 0 +------------------------+ F | 1 2 3 4 5 6 7 8 |<--SWITCH NUMBER STAMPED F |------------------------| ON SWITCH PACK ||O||O||O||O||O||O||O||O|| ||N||F||F||N||F||N||N||N|| || ||F||F|| ||F|| || || || +------------------------+ (OFF = 1) 5.6 11/750-70 KERNEL REVISION SUMMARIES ----------------------------------- o Note that the difference between Revs 70, 78 and 7C is the backplane rev and the memory - 70 contains the Rev "B" backplane and 16K memory (L0011 controller and M8728 arrays); 78 machines contain the Rev "C" backplane and 64K memory (L0016 controller and M8750 (or M8728 arrays); 7C contains the Rev "D" backplane and 4MB memory (L0022 controller and M7199) or M8750 arrays. This will result in some differences, but most information for Rev 7 applies to 70, 78 and 7C machines. The differences will be noted. Creation date is May 1984 - manufacturing implementation date. o FCO implementation July 1984. EQ numbers for Rev 7 are the same as Rev 6: L0003 - EQ-01201-05; L0004 - EQ-01201-04; if required, L0008-YA - EQ-01201-01 or L0008-YB EQ-01201-02. o Rev 7 incorporated all fixes from Rev 5 and Rev 6 EXCEPT for the cache parity fix (See above section). This fix has been disabled on Rev J1/J2 L0003s. NOTE: L0003 and L0004 revisions should be checked prior to ordering Rev 7 material. Manufacturing is known to have shipped Rev 7 L0003s and L0004s while still setting the SID switch at 68. o Rev 7 ECOs: ECO # Part Rev Problem/Correction Quick Check ----- -------- ------------------- ----------- L0003-TW006 J1/J2 1. Disables cache parity E109 pins 4,5 fix in L0003-TW005 6 are grounded 2. Corrects glitch on stall L signal L0003-TW007 K1/K2 1. Remove leftover wires No wire from (field/ from L0003-TW006 E86-5 to E1-11 repair centers) K3 1. Remove leftover wires E17 is spare (module from L0003-TW006 and location build) unused component L0004-TW008 M1/M2 1. Corrects arbitration E11 is 23-656A2 problem on the CMI during interrupts (UBI/UDA "Hang" problem) L0004-TW009 N1/N2 1. Replace MAP rams with E60-62, E70-72, NMOS rams E81, E82, E92, E102 are 9122s These ECOs are NOT part of the Rev 7 FCO, but were phased into mfg. and repair centers at a later date. o Rev 7 ECOs are REQUIRED for CI750 and DR750. o Related FCOs: DW750-R-0002 and UDA50-R-0005 should be installed with Rev 7 (See section 6.4 in this document for details). FP750-R-0002 should also be installed with Rev 7. (See Section 6.2) o Compatible Revision Levels Microcode - Rev 98 or greater NOTE: Rev 99 began shipping from SDC in Diagnostic Release 22 - 12/30/85. This latest rev fixes bugs with CALLS, BBSSI/BBCCI HW Int. lock EDITPC 'Double Match' R0 corruption, Invalid SCBB "Ucode Hang' and MTPR "CC mismatch source' errors. VAX/VMS - Version 3.X or greater EVNDX - Minimum EVNDX release is 15 (March 1984). o Quick check Rev 70: I 0000003E 02005F70 (5F on power up - ucode Rev 95) I 0000003E 02006270 (62 with Rev 98 ucode loaded) o SID Switch Setting Rev 70: SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 ON OFF OFF OFF ON ON ON ON 5.7 11/750-78 KERNEL REVISION SUMMARIES ----------------------------------- o Section 5.8 applies (through the Compatible Revison Levels) to 11/750-70, 11/750-78 and 11/750-7C as well. o Quick check Rev 78: I 0000003E 02005F78 (5F on power up - ucode Rev 95) I 0000003E 02006278 (62 with Rev 98 ucode loaded) o SID Switch Setting Rev 78: SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 ON OFF OFF OFF OFF ON ON ON 5.8 11/750-7C KERNEL REVISION SUMMARY --------------------------------- NOTE: Only the Rev "C" backplane may be reworked to a rev "D" to accomodate the new (4MB) memory upgrade. o A Revision 7C will be created by Field Service upon installation of the MS750-HB option. This system revision (7C) will never ship from manufacturing. o Quick Check Rev 7C: I 0000003E 02005F7C (5F on power up - ucode Rev 95) I 0000003E 0200627C (62 with Rev 98 ucode loaded) SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 ON OFF OFF OFF OFF OFF ON ON 5.9 11/750-80 KERNEL REVISION SUMMARY --------------------------------- o The difference between 80, 88 and 8C are the same as described in section 5.8 for 70, 78 and 7C machines, i.e. the backplane revs and memory modules. o Rev 8 ECOs: ECO # Part Rev ----- -------- L0011-005 E1 L0016-003 C1 L0022-001 B2 PROBLEMS FIXED BY ABOVE ECOS: ---------------------------- 1 - Patchable control store is not loaded at boot time. 2 - UDA50 boot ROM CODE does not allow enough time for RA60 to spin up after power fail. 3 - ROM code for TU58 does not allow enough time for TU58 to initialize. 4 - Massbus boot ROM code has wrong hex code for RP07 drive. FCO 11750-I008 currently being implemented. EQ-01453-01 - Boot ROMS EQ-01453-02 - REV 99 ucode FA-04739-01 - FCO document o Quick check Rev 80: L0011 - E81 is 23-E41A9-00 L0016 - E44 is 23-E41A9-00 L0022 - E48 is 23-E41A9-00 SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON ON ON ON ON ON o Quick check Rev 88: L0011 - E81 is 23-E41A9-00 L0016 - E44 is 23-E41A9-00 L0022 - E48 is 23-E41A9-00 SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON ON OFF ON ON ON o Quick Check Rev 8C: L0011 - E81 is 23-E41A9-00 L0016 - E44 is 23-E41A9-00 L0022 - E48 is 23-E41A9-00 SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON ON OFF OFF ON ON 5.10 11/750-90 KERNEL REVISION SUMMARY --------------------------------- o The difference between 90, 98 and 9C are similar to that described in section 5.8 for 7X and 8X machines, i.e. the backplane revs and memory modules. PROBLEMS FIXED WITH REVISION 9: 1 - REMQUE Instruction. 2 - CMT 103 required for support of VMS V5. FCO: 11750-I009 involved installing latest rev console microcode, Rev 103. No EQ kits were made available. Latest microcode was shipped from SDC in October, 1988. Rev 90: SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON OFF ON ON ON ON Rev 98: SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON OFF FF ON ON ON Rev 9C: SYS ID <7> <6> <5> <4> <3> <2> <1> <0> SWITCH S1 S2 S3 S4 S5 S6 S7 S8 OFF ON ON OFF OFF OFF ON ON 6.0 OPTION REVISION HISTORY ----------------------- The option interfaces and adaptors will have a separate revision history from the kernel. A revision change to these options will not affect the kernel revision. ---------------------------------------------------------------- OPTION RH750 L0007 MBA Module -------------------------------------------------------- KU750 (WCS) L0008-YB Replaces existing KU750-YG -------------------------------------------------------- FP750 L0001 FPA Module -------------------------------------------------------- DW750 L0010 2nd Unibus Module -------------------------------------------------------- DR750 L0014 Interprocessor I/F Module -------------------------------------------------------- KC750 L0006 Remote Diagnosis Option ---------------------------------------------------------------- Each option revision summary will indicate any hardware, operating system, diagnostic and microcode constraints. The option will be considered compatible with the kernel hardware, VMS and microcode revisions used during the development of the option. Earlier compatible revisions will be noted only if they have been tested and proven to work. Compatible module revisions are separated by commas. Pertinent diagnostics to be run for each option (and the required revision, if any) will also be noted. 6.1 RH750 OPTION REVISION DESCRIPTION ------------------------------------ -----------------------------------------------------------------+ RH750 Revision | 00 | 01 | 02 | 03 | 04 | -----------------------------------------------------------------| MODULE | SLOT | ETCH | | | | | | -----------------------------------------------------------------| L0007 | 7,8 or 9 | C | CS=A | CS=A1 | | | | | | | MR=A | MR=B | | | | | | D | | CS=B,C| | | | | | | | MR=B,C| | | | -----------------------------------------------------------------+ RH750-00 REVISION SUMMARY -------------------------- o Creation date is FCS - April 1981. o This represents the initial introduction of revision control for the RH750 and represents the minimum revision level for the L0007 module at FCS. o Diagnostics - ECCAA and EVRAA. RH750-01 REVISION SUMMARY -------------------------- o Creation date is October, 1981. o Represents RH750-R-0001 FCO, which consisted of ECO L0007-TW002 to fix the problem of data lates on multiple MASSBUS systems. Replace 23-909A9 at location E12 with 23-969A9. o FCO done on "C" etch modules only. Etch Revision "D", Module Rev "B" is a relayout of the L0007 module and is equivalent to Etch Rev "C", Module Rev "A1". o Diagnostics - ECCAA and EVRAA. o Quick Check for Rev A1 - E12 is 23969A9-00. 6.2 FP750 OPTION REVISION DESCRIPTION ----------------------------------- -----------------------------------------------------------+ FP750 Revision | 00 | 01 | 02 | 03 | 04 | -----------------------------------------------------------| MODULE | SLOT | ETCH | | | | | | -----------------------------------------------------------| L0001 | 1 | D | CS=B|CS=C |PR=E2 | | | | | | MR=B|MR=C,D| | | | | | E | |CS=D |PR=E1 | | | | | | |MR=D | | | | -----------------------------------------------------------+ FP750-00 REVISION SUMMARY --------------------------- o Creation date is FCS - December 1981. This represents the minimum module revision level required at FCS. o 11750 kernal rev must be at Rev 3 (Rev 94 microcode required). o Diagnostics - ECKAB (min. rev. 7.2) - EVNDX 4.0 (Jan 1982) ESCAA (min. rev. 6.4) - " EVKAB (min. rev. 2.5) - " EVKAC (min. rev. 4.0) - " FP750-01 REVISION SUMMARY --------------------------- o Creation date is March 1982. o Represents FP750-R-0001 FCO consisting of ECO L0001-TW002, which fixes the problem of the FPA not powering up "enabled" due to incomplete initialization of circuitry. o Diagnostics - ECKAB (min. rev. 7.2) - EVNDX 4.0 (Jan 1982) ESCAA (min. rev. 6.4) - " EVKAB (min. rev. 2.5) - " EVKAC (min. rev. 4.0) - " o Quick check for MR C - Wire on E33-10. FP750-02 REVISION SUMMARY --------------------------- o Creation date is March 1984 - Manufacturing implementation date for L0001-TW004. o ECO fixes problem of the Q1 transistor on the L0001 module burning out, causing failure of the FP750. New Part Revisions: Etch D = Part Rev E2; Etch E = Part Rev E1. o FCO available in Q1FY85. This should be implemented with Rev 7 if FP750 option present. EQ kit number is EQ-01281-01. This is a module replacement FCO; the FCO program is being controlled due to limited material availability. Contact your regional/country FCO coordinator for ordering procedures. o Quick check for Rev E1/E2: R33 is 75 OHM Resistor. o EVNDX.15 (March 1984) minimum diagnostics for FP750. -28- 6.3 KU750 OPTION REVISION DESCRIPTION ---------------------------------- ---------------------------------------------------------------+ KU750 Revision | 00 | 01 | 02 | 03 | 04 | ---------------------------------------------------------------| | SLOT | ETCH | | | | | | ---------------------------------------------------------------| 5413865-C| attaches| C |CS=B | | | | | |to L0005 | |MR=C | N/A | N/A | | | ---------------------------------------------------------------| L0008-YB | 5 | A | |PR=C2 | PR=C2| | | ---------------------------------------------------------------+ G&H | | |M198A |T909A |T909C | | | Microcode | | |(2.0) | | | | | ---------------------------------------------------------------+ KU750-00 REVISION SUMMARY -------------------------- o Creation date is FCS - March 82. o This represents the minimum module revision level required at FCS. o Requires KU780-YG microcode rev at 2.0 or higher (P/N BE-M198A-DE). This TU58 tape is shipped with the KU750-YG option. The middle 5 digits of this part number will be tracked in the above chart, as the letter on the right will be bumped when the microcode changes. o Diagnostic - ECKAX - 11750 Cluster Exerciser - EVNDX 7.0 (July 82) (minimum rev 3.4) KU750-01 REVISION SUMMARY ------------------------- o Creation date was June, 1984. o Quick check for C2 is: Wire from E188-12 to E192-09. o New packaging for KU750 (WCS) option; the KU750-YG (5413865-C) replaced by the L0008-YB module. Microcode was also changed - new part number is BE-T909A-ME. o All existing KU750-YG customers under contract will be upgraded with an L0008-YB as part of FCO Rev 7. o Existing KU750-YG customers will also be upgraded with new KU750 microcode. FCO will be available in Q3FY85. o Current version of the microcode is compatible with VMS 3.X. It is compatible with VMS V4 until the "VMSUPDATE" procedure can no longer be used (projected to be VMS 4.2) At that time, use of "VMSINSTALL" will be required. KU750 microcode is being updated to support "VMSINSTALL" and will be available prior to the release of VMS 4.2. KU750-02 REVISION SUMMARY ------------------------- o Creation date was October, 1988. o Revision C, BE-T909C-ME, is required when running VMX 5.0. 6.4 DW750 OPTION REVISION DESCRIPTION ---------------------------------- ------------------------------------------------------------+ DW750 Revision | 00 | 01 | 02 | 03 | 04 | ------------------------------------------------------------| MODULE | SLOT | ETCH | | | | | | ------------------------------------------------------------| L0010 | 10 | C | CS=B |PR=C1 |PR=E1,| | | | | | MR=B | | E2,F1| | | ------------------------------------------------------------+ DW750-00 REVISION SUMMARY -------------------------- o Creation date is FCS for the DW750 option - September 1982. o 11750 kernel must be at rev 3 or higher. o Requires VMS Version 3.0 or higher. o Diagnostics - ECSAA - min. rev 6.4 - EVNDX Release 4.0 (Jan 82) ECCBA - min. rev 1.3- " " " " DW750-01 REVISION SUMMARY ------------------------- o Creation date is 5/31/83 - manufacturing ship date. o Consists of the following ECO: L0010-TW002 - on DATI with offset and Unibus address bits 0 and 1 asserted, the microsequencer may branch to the DATOB flow. - offset transfers across page boundaries retain old map values. o FCO (DW750-R-0001) was implemented in the field beginning in September 1984, to be installed with FCO 11/750 Rev 5. NOTE:: FCO HAS BEEN CANCELLED AS OF 3/15/84. ANOTHER FCO, DW750-R-0002 WAS IMPLEMENTED AT A LATER DATE. ANY EQ KITS THAT HAVE BEEN ORDERED FOR THIS FCO SHOULD BE CANCELLED (EQ-01189-00). o Following diagnostics updated and available in Release 12: Diagnostic Min Version Title ---------- ----------- ----- ECCBA 1.3 VAX 11/750 UBI/DW750 Diag ECSAA 6.10B VAX 11/750 Diag Supervisor o Quick check - E50 is 23-991A9-00 DW750-02 REVISION SUMMARY ------------------------- o Creation date is July 1984. o Rev 2 ECOs: ECO # Part Rev Problem/Correction Quick Check ----- -------- ------------------ ----------- L0010-TW004 D1 1. Corrects arbitration E28 is problems on the CMI 23-656A2-00 during interrupts. (UBI/UDA hang problem) L0010-TW005 E1 1. Corrects micro- Jumper between sequencer branching E56.11 and errors. E24.5 * L0010-TW006 E2 1. Replace 19-09704-00 E91 is 19-10389 w/19-10389-00 (no longer available) * L0010-TW007 F1 1. Replace MAP rams E55,E68,E81,E82 w/NMOS Rams E92-E97 * These ECOs are NOT part of FCO DW750-R-0002; they were phased into mfg. and the repair centers at a later date. o L0010-TW004 and L0010-TW005 were implemented together in the field as part of FCO DW750-R-0002. Mfg. shipped L0010s at "D1" until 9/84 in the U.S.and GIA (7/84 in Europe). These will have to be upgraded to "E1" as part of the FCO. L0010 Rev "C" and above can be reworked in the field; Rev "B" or below L0010s must be replaced. EQ kits: Module Replacement (L0010) - EQ-01280-01 Rework (for Rev C or higher) - EQ-01280-02 EQ-01280-02 is a controlled FCO kit due to material shortages. Contact your regional/country FCO coordinator for ordering info. o Diagnostics EVNDX.15 (May 1984) 6.5 DR750 OPTION REVISION DESCRIPTION ----------------------------------- ------------------------------------------------------------+ DR750 Revision | 00 | 01 | 02 | 03 | 04 | ------------------------------------------------------------| | SLOT | ETCH | | | | | | ------------------------------------------------------------| L0014 | | A | CS=A | PR=B1| | | | | | | MR=A | | | | | ------------------------------------------------------------| DR750 | | |T326A |T326A | | | | Microcode | | | | | | | | ------------------------------------------------------------+ DR750-00 REVISION SUMMARY ------------------------- o Creation date is FCS - September 1982. This represents the minimum revision level required at FCS. o 11750 kernel rev must be 30/38 or higher. o DR750 requires a CML gate array (PN 19-14725-00) at location E103 on the L0003 module. CML is packaged with the DR750 option and must be installed on the L0003 module during DR750 installation. (See DR750 installation procedures.) o Microcode rev will be tracked by the middle 5 digits of the part number for the TU58 tape (BE-M198A-DE). The letter on the right will be bumped when the microcode is updated. o Requires VMS Version 3.0. o Diagnostics - EVDFD - rev 1.0 - EVNDX Release 7.0 (July 82) EVDFE - Rev 1.0 - " EVDFF - rev 1.0 - " EVDFG - rev 1.0 - " ECDFA - rev 1.0 - " ECDFB - rev 1.0 - " ECSAA - min rev 6.7 - " DR750-01 REVISION SUMMARY ------------------------- o Creation date is April 1984 - manufacturing implementation of ECO L0014-TW001. o Either a CI750 or DR750 can be present in the machine - not both. o 11/750 CPU must be at Rev 70/78. o ECO fixes problem of local memory parity errors on DR750. DR750 has been on hold pending this ECO, so volumes are low (less than 10). Any L0014s at Rev "A" should be replaced with Rev "B1". o No diagnostic or microcode changes required for this ECO. 6.6 KC750 OPTION REVISION DESCRIPTION ---------------------------------- -------------------------------------------------------------------+ KC750 Revision | 00 | 01 | C | | | -------------------------------------------------------------------| Module | SLOT | ETCH | | | | | | -------------------------------------------------------------------| L0006 | | A | MR=*2 | MR=*3 | -- | | | | | B | MR=B | MR=B1 | PR=C1 | | | | | C | MR=C | MR=D | PR=E1 | | | -------------------------------------------------------------------+ KC750-00 REVISION SUMMARY -------------------------- o Creation date is FCS - 10/80. This represents the minimum revision level required at FCS. KC750-01 REVISION SUMMARY -------------------------- o This represents L0006-TW004. Manufacturing began shipping on 22 February 1982. o The ECO fixes a problem with the KC750 firmware which makes it possible to remotely load data into 11/750 memory, corrupting the customer's running system, even while the keyswitch is in remote/secure position. FCO KC750-R-0001 will be done in conjunction with Rev 5, projected to be September 1984. o FCO will be module rework for Etch B and C. Etch A is multiwire; field rework should not be attempted on these modules. o Quick Check - Wires on E6-3,4; E12-12,13; E42-13; E133-12,13,14,15; E176-24; and E187-5. Etch cuts on side 2 near E42-13 and E187-5. o Diagnostics - ECKAF - Version 3.1 (Diagnostic Release 9). KC750-C REVISION SUMMARY -------------------------- o This represents ECO L0006-MR005. o Quick Check - Wire from E106.14 to E85.2. o The ECO fixes a problem with the RDM (Remote Diagnostic Module). L0006 module intermittently fails to drive WBUS properly causing false micro-diagnostic errors. NOTE: Etch A is no longer supported. These will be scrapped as they are returned from the field. New rev of L0006 modules are as follows: Etch B Part Rev B1 Etch C Part Rev C1 6.7 CI750 OPTION REVISION DESCRIPTION ----------------------------------- ------------------------------------------------------------------------ CI750 | B | C | D,(**DD1)| E | F | H -------------------------------------------------------------|-------- L0100*** | D | D | D | D1 | E2| | L0118*** | - | - | - | - | - | B L0101 | H | H | H, **HH1| J,K | K | L0009 | A | A | A | A | A | B L0400 | B | B | B | B | B | B Microcode | | | | | | CI780.BIN | Rev 2.0 | Rev 3.0| Rev 4.0 | Rev 5 | Rev 7 | Rev 8 BE-T204*-ME| E-F | G | H | I | L | O | | | |**Rev 6 | | Backplane | B | B | B | B | B | B ----------------------------------------------------------------------- POWER SUPPLY A A A A A A * (NOTE) "B2" is being marked on "B" etch and is equal to "D1". ** (NOTE) Rev 6.0 ucode and the "HH1" module are only used if you need to install FCO CI750-DD1-I-004 making the CI750 Rev DD1. *** (NOTE) L0118 is enhanced L0100 replacement and can be used as "universal spare". L0118 is required to support >16 node functionality. Rev "F" incorporates the CI750-I006 FCO which upgrades the L0009 and fixes the following: another VAXcluster node randomly receives incorrect data in data-packet originating from VAX750/CI750;, when a VAX750 "single-bit or double-bit" main-memory (MS750-XX) error is encountered by the CI750. ** NOTE: VMS V5 requires the CI750 to be at a minimum revision of "F1" CI750-00 REVISION SUMMARY ------------------------- o Creation date is May 1984 - FCS. The above chart for Rev 00 represents the minimum revision levels at FCS. o 11/750 CPU must have a minimum of 2 megabytes of physical memory. o Requires VMS version 3.5 or higher. 3.5 requires CPU to have a local disk. Only VMS operating system supported. o 11/750 CPU without a UDA50 must be at Revision 50/58 or higher - i.e. PCS (L0008-YA or L0008-YB hardware) must be installed in Slot 5 of the CPU. 11/750s running UDA50s must be at Rev 70/78. o Minimum 11/750 (PCS) microcode revision is 97. o Diagnostics Diag Minimum Rev Title ---- ----------- ----- ECSAA 6.11 Diag Supervisor ECCGA 1.0 CI750 Repair Level Diag 1 ECCGB 1.1 " " " " 2 ECCGC 1.0 " " " " 3 ECCGD 1.1 " " " " 4 ECCGE 1.1 " " " " 5 EVGAA 1.1 CI Functional Diag 1 EVGAB 1.1 " " " " 2 CI750-B1 REVISION SUMMARY ------------------------- o Creation date is November 1984 - mfg. ship date. o CI750-B1 ECOs: ECO # Part Rev Problem/Correction Quick Check ----- -------- ------------------ ----------- L0101-TW006 H1 1. Virtual circuits are closed by un- recognized commands. 2. Virtual circuit closure due to micro confusion. 3. Port hangs due to conflict in queue access. Correction is V3.0 CI microcode. NOTE THAT L0101 REV H1 AND CI780.BIN REV 3.0 MUST BE USED TOGETHER. o FCO to upgrade all CI750s will be implemented in December 1984. EQ-01309-01 ROMS for L0101 module EQ-01309-02 11/750 Console, BE-T204G-ME (CI780.BIN Rev 3.0) o This FCO is part of VAXcluster Rev D1. Other FCOs that could be needed to bring the Cluster to Rev D1 are: FCO H/W Rev CI780-R-00C1 Rev C1 HSC50-R-0006 Rev C1 RA80X-R-0002 Rev B0 RA60-R-0003 Rev A5 These FCOs should be installed prior to or during VMS V4.0 installation. Note that although VMS Release notes state that earlier revisions are acceptable, i.e. will probably work, engineering and product management has determined that the customer needs all these FCOs for acceptable cluster performance under VMS V4.0. Details of Cluster Rev D1 requirements were sent to all branch managers. Contact your regional/country FCO coordinator for ordering info on these FCOs. Refer to the Cluster Revision Control document for more information on Cluster Rev D1 requirements. o Minimum requirement for CI functional diagnostics (EVGAA, EVGAB) is 1.1. CI750-C1 REVISION SUMMARY ------------------------- o Creation date is May 1985 - mfg. ship date. o Problem/Symptom: Funcional Problems discovered in testing: ECO # Part Rev Problem/Correcrtion Quick Check ----- -------- ------------------- ----------- L0101-TW006 H1 1. FCO CI750-R00B1 V3.0 microcode introduced "MISC. ERROR TYPE-12 & 13 (hex B & C)", in variance with CI-Arch. Spec., and resulting in VMS CI-PORTS RE-INITS. Correction: Release of V4.0 CI-MICROCODE -39- NOTE: This FCO includes CI750-R00B1, released 27-Nov-84 and ammended 20-Feb-85. CI750-R00B1 is not a prerequisite. o FCO to upgrade all CI750s will implemented in May, 1985. EQ-01343-02 11/750 Console, BE-T204H-ME (CI780.BIN Rev 4.0) If your system is not at "B1", also order EQ-01343-01 ROMS for the L0101 module CI750 Revision "D1"** --------------------- o Creation Date - November 1985. This revision changed the CI750 from "C" to "D". There was no hardware ECO required. This was a microcode change only. The CI780.BIN file changed from V3.0 to V4.0 - console media BE-T204I-DE. This fixed problems found during extensive in-house testing of very large VAXclusters under specific conditions, where the CI750 interface will sometimes incorrectly recover from CI error conditions. Comments: An FCO was generated. It was recommended that the new FCO be implemented on all CI750's and VAX8600's. EQ-01364-01 - CI780.BIN Rev. V5.0 (11/750 console media) CI750 Revision "E1"** ------------------- o Creation Date - July, 1986 This revision changes the CI750 from "D1" to "E1". This revision change involved an ECO to the L0101 as follows: L0101-MK009 - 1. Numerous Functional Errors ("arbitration timeout", "internal queue retry error"). 2. Need a variable sanity timer. 3. Need to check the "valid" bit when referencing a cached buffer descriptor. 4. Correct documentation errors. This is a microcode and ROM change. Requires CI780.BIN V7.0 BE-T204I-DE. Comments: An FCO was generated which brought the CI750 to Rev "E1". This FCO, CI750-E1-I004, should have been installed on all CI750s. -40- EQ-01421-01 ROMS for the L0101 module EQ-01421-02 CI780.BIN V7.0 (11/750 console media with diagnostics) EQ-01421-03 CI780.BIN V7.0 (11/750 console media without diagnostics) FA-04706-01 FCO Document (included with all EQ kits) L0101-MK010 - 1. Paths crossed, REQID sent on path A, response on path B. 2. Clock the transmit enable flop correctly to prevent cluster hang. Rework is two etch cuts and two wire adds. This ECO brings the L0101 to Rev "K1". Module Part Revs "J1" and "K1" are both acceptable in CI750 Rev "E1". CI750 Revision "F1" ------------------- o Creation Date - September, 1988 This revision changes the CI750 from "E1" to "F1" This revision change involved the following eco: L0009-MK003 - 1. CMI control state machine selects incorrect command/address and function/vector register data onto the bus during certain state transitions. Problem observed after detection of CRD Memory error by the port CMI interface and may result in data corruption. Comments: An FCO is being generated from the L0009-MK003 ECO. FCO is CI750-I006. This will be done in all CI750s. FCO estimated to begin September, 1988. EQ-01497-01 Contains microcode ROM. EQ-01497-02 Contains L0009 Module Rev B2 or C3. FA-04792-01 Contains FCO document. NOTE: Rev "F1" may also include FCO CI750-I005 for clusters containing 6 nodes and above. This FCO involves an eco to the L0118 module as follows: L0118-LK002 - Too many etch cuts and wires on board. New etch rev requires extra jumpers and stake pins. Implementation of FCO CI750-I005 began May, 1988. CI750 Revision "H3" ------------------ o Creation date is May 1988. o This revision changed the CI750 from "F" to "H". o This revision documents the introduction of the LO118 module Problem/Correction - N/A. Quick Check - verify module is LO118. Diagnostic Release 28 (EVNDX 28) contains the minimum usable diagnostics for the LO118 module. \\VAX_REV_MATRIX