ANTS/ISI IMP Interface

From Computer History Wiki
Jump to: navigation, search

The ANTS IMP Interface and ISI IMP Interface were two mostly-program compatible IMP interfaces, the former produced as part of the ARPA Network Terminal System project, the latter at ISI.

Little is currently known of their physical implementation, and in particular if they shared a logic design, or just their programming interface specification. They provided an 1822 interface for the UNIBUS which used DMA to transfer data to/from main memory.

Differences

The ANTS and ISI versions have only minor differences:

  • The register which specifies the extent of a transfer; the ANTS one gives the ending address, the ISI one gives the transfer size
  • The ISI one has two extra bits of transfer memory address; without those, the ANTS one is restricted to using buffers in the lowest 64KB of memory

Registers

Register Abbreviation Address
Input Start Pointer Register IMPSPI 0764000
Input End Pointer/Byte Count Register IMPEPI/IMPBCI 0764002
Input Status Register 1 IMPS1I 0764004
Input Status Register 2 IMPS2I 0764006
Output Start Pointer Register IMPSPO 0764010
Output End Pointer/Byte Count Register IMPEPO/IMPBCO 0764012
Output Status Register 1 IMPS1O 0764014
Output Status Register 2 IMPS2O 0764016

0764000: Input Start Pointer Register (IMPSPI)

SP15 <---> SP00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764002: Input End Pointer (IMPEPI) ANTS

EP15 <---> EP00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764002: Input Byte Count Register (IMPBCI) ISI

BC15 <---> BC00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764004: Input Status Register 1 (IMPS1I)

IMPERR NEXMEM Unused BCEQ0 BUSY Unused ENDMSG BUFULL INTENA Unused NOSWAP Unused MEMEX Unused
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • IMPERR - IMP error
  • NEXMEM - Non-existent memory
  • BCEQ0 - Byte count=0
  • ENDMSG - End of message
  • BUFULL - Buffer full
  • INTENA - Interrupt enable
  • NOSWAP - Suppress byte swapping
  • MEMEX - Memory address extension (ISI only)

0764006: Input Status Register 2 (IMPS2I)

Unused TSTINC LOCK LOOP IMPRDY Unused SCOSYN
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • TSTINC - Test increment
  • LOCK - Lock interface (don't start when EPI/BCI is loaded)
  • LOOP - Loop output to input
  • IMPRDY - IMP master ready
  • SCOSYN - Scope sync

0764000: Output Start Pointer Register (IMPSPO)

SP15 <---> SP00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764002: Output End Pointer (IMPEPO) ANTS

EP15 <---> EP00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764002: Output Byte Count Register (IMPBCO) ISI

BC15 <---> BC00
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

0764004: Output Status Register 1 (IMPS1O)

Unused NEXMEM Unused BCEQ0 BUSY Unused DONE INTENA Unused NOSWAP Unused MEMEX DISEOM
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • NEXMEM - Non-existent memory
  • BCEQ0 - Byte count=0
  • INTENA - Interrupt enable
  • NOSWAP - Suppress byte swapping
  • MEMEX - Memory address extension (ISI only)
  • DISEOM - Disable end of message

0764006: Output Status Register 2 (IMPS2O)

Unused IRESET Unused HOSRDY
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • IRESET - Interface reset
  • HOSRDY - Host master ready

External links