Difference between revisions of "H754 +20V, -5V Regulator"
(20/5 tradeoff) |
(rm bogosity) |
||
| Line 1: | Line 1: | ||
The '''H754 +20V, -5V Regulator''' is one of the [[DEC standard modular regulator]]s. It can produce an output [[current]] of up to 8A at an output [[voltage]] of +20V, and up to 1A at -5V. (Technically, the two trade off with each other, so if there is less +20V being drawn, more -5V can be drawn, up to a maximum of 8A.) It has over-current and over-voltage detection and protection. | The '''H754 +20V, -5V Regulator''' is one of the [[DEC standard modular regulator]]s. It can produce an output [[current]] of up to 8A at an output [[voltage]] of +20V, and up to 1A at -5V. (Technically, the two trade off with each other, so if there is less +20V being drawn, more -5V can be drawn, up to a maximum of 8A.) It has over-current and over-voltage detection and protection. | ||
| − | It was a [[switching power supply]], one of the earliest; however, the basic concept was | + | It was a [[switching power supply]], one of the earliest; however, the basic concept was somewhat different from later supplies of this type. It takes as input [[alternating current|AC]] at a [[voltage]] of 20V-30V, runs it through a [[diode]] bridge and filter [[capacitor]] to convert it to [[direct current|DC]]. That is then used to produce a 25V output (+20V to -5V); a pair of shunt [[voltage regulator]]s then produce the two output voltages. |
| − | |||
| − | It takes as input [[alternating current|AC]] at a [[voltage]] of 20V-30V, runs it through a [[diode]] bridge and filter [[capacitor]] to convert it to [[direct current|DC]]. That is then used to produce a 25V output (+20V to -5V); a pair of shunt [[voltage regulator]]s then produce the two output voltages. | ||
It took its AC input on pins 7 and 8; the +20V output was on pin 5, the -5V on pin 3, and the [[ground return]] on pin 2. Pins 1, 4 and 6 were not connected. | It took its AC input on pins 7 and 8; the +20V output was on pin 5, the -5V on pin 3, and the [[ground return]] on pin 2. Pins 1, 4 and 6 were not connected. | ||
<!-- run through several large [[transistor]]s controlled by a monolithic [[integrated circuit]] --> | <!-- run through several large [[transistor]]s controlled by a monolithic [[integrated circuit]] --> | ||
| + | {{semi-stub}} | ||
| + | |||
{{semi-stub}} | {{semi-stub}} | ||
[[Category: DEC Hardware]] | [[Category: DEC Hardware]] | ||
Revision as of 16:03, 26 September 2018
The H754 +20V, -5V Regulator is one of the DEC standard modular regulators. It can produce an output current of up to 8A at an output voltage of +20V, and up to 1A at -5V. (Technically, the two trade off with each other, so if there is less +20V being drawn, more -5V can be drawn, up to a maximum of 8A.) It has over-current and over-voltage detection and protection.
It was a switching power supply, one of the earliest; however, the basic concept was somewhat different from later supplies of this type. It takes as input AC at a voltage of 20V-30V, runs it through a diode bridge and filter capacitor to convert it to DC. That is then used to produce a 25V output (+20V to -5V); a pair of shunt voltage regulators then produce the two output voltages.
It took its AC input on pins 7 and 8; the +20V output was on pin 5, the -5V on pin 3, and the ground return on pin 2. Pins 1, 4 and 6 were not connected.
