Difference between revisions of "DUP11 synchronous serial line interface"

From Computer History Wiki
Jump to: navigation, search
(Basic info)
 
(Add rcv regs)
Line 24: Line 24:
 
|Transmitter Data Buffer Register          || TxDBUF || 16xxx6
 
|Transmitter Data Buffer Register          || TxDBUF || 16xxx6
 
|}
 
|}
 +
<!-- The [[address]]es shown are for the first DP11-A in a system; additional ones are normally set to be at 774760, 774750, etc to 774400. -->
  
−
<!-- The [[address]]es shown are for the first DP11-A in a system; additional ones are normally set to be at 774760, 774750, etc to 774400.
+
===16xxx0: Receiver Status Register (RxCSR)===
  
−
===774770: Receiver Control and Status Register (DPRCSR)===
+
{{16bit-header}}
 +
| DSCA || RING || CTS || CARR || RACT || SECRCV || DSR || SSYNC || RDN || RDIE || DSIE || REN || SECXMT || RTS || DTR || DSCB
 +
{{16bitoctal-bitout}}
 +
 
 +
* DSCA - Data Set Change A; set for any change on Ring, Clear to Send (optionally DSCB lines)
 +
* RING - Ring Indicator
 +
* CTS - Clear to Send
 +
* CARR - Carrier
 +
* RACT - Receiver Active; set after the first character has been assembled
 +
* SECRCV - Secondary Receive Data
 +
* DSR - Data Set Ready
 +
* SSYNC - Strip Sync; sync characters following the first are discarded - only used with byte-oriented protocols
 +
* RDN - Receive Done Flag; set  when the receive buffer contains an assembled character
 +
* RDIE - Receive Interrupt Enable; allows an input interrupt when Receive Done is set
 +
* DSIE - Data Set Interrupt Enable; allows an input interrupt when DSCA is set
 +
* REN - Receiver Enable; when first set, the receiver looks for synchronization
 +
* SECXMT - Secondary Transmit Data
 +
* RTS - Ready to Send
 +
* DTR - Data Terminal Ready
 +
* DSCB - Data Set Change B; set for any change on Carrier, Data Set Ready, Secondary Received Data
 +
 
 +
===16xxx2: Receiver Data Buffer Register (RxDBUF)===
  
 
{{16bit-header}}
 
{{16bit-header}}
−
| colspan=3 | Unused || CPAR || RACT || colspan=3 | BPCH || RDN || RDIE || colspan=2 |  Unused || MRCV || MAINT || HLFD || STRS
+
| ERR || OVR || Rsvd || RCRC || Rsvd || RABO || REOM || RSOM || colspan=8 | DDAT
 
{{16bitoctal-bitout}}
 
{{16bitoctal-bitout}}
  
−
* CPAR - Character Parity; parity of last character in the receive buffer
+
* ERR - Error
−
* RACT - Receiver Active; set after two consecutive sync characters
+
* OVR - Overrun
−
* BPCH - Bits per Character, selects between 6-8, 10-12 bits per character
+
* RCRC - Receiver CRC
−
* RDN - Receive Done Flag; set when the receive buffer contains an assembled character
+
* RABO - Received Abort
−
* RDIE - Receive Interrupt Enable; allows an input interrupt when Receive Done Flag is set
+
* REOM - End of Received Message
−
* MRCV - Miscellaneous Receive; monitor any non-standard modem status
+
* RSOM - Start of Received Message
−
* MAINT -Maintenance Mode; connect Transmitter output to Receiver input, CTS simulation
+
* RDAT - Received Data Buffer
−
* HLFD - Half Duplex; RTS on inhibits Receive logic
+
 
−
* STRS - Strip Sync; sync characters following Receive Active are discarded
+
===16xxx2: Parameter Status Register (PARCSR)===
 +
 
 +
{{16bit-header}}
 +
| DEC || colspan=2 | Rsvd || SEC MD || colspan=2 | Rsvd || CRC INH || Rsvd || colspan=8 | SEC ADDR/RSYNC
 +
{{16bitoctal-bitout}}
 +
 
 +
* DEC - DEC Mode
 +
* SEC MD - Secondary Mode
 +
* CRC INH - CRC Inhibit
 +
* SEC ADDR/RSYNC - Secondary Station Address / Receiver Sync
  
−
===774774: Transmitter Control and Status Register (DPXCSR)===
+
<!--
 +
===16xxx4: Transmitter Status Register (TxCSR)===
  
 
{{16bit-header}}
 
{{16bit-header}}

Revision as of 19:29, 29 March 2020

DUP11 M7867 board

The DUP11 is an early synchronous serial line interface for the UNIBUS. Like the earlier DP11-A, it used programmed I/O (with separate receive and transmit interrupts) to transfer data; it was double-buffered for both input and output. It could operate in either half-duplex or full-duplex, at baud rates up to 9.6K bits/second.

Both byte-oriented (e.g. DDCMP, BISYNC) and bit-oriented (e.g. SDLC, HDLC) protocols were supported; a variety of CRC algorithms, depending on the[protocol in use on the line, were supported for error detection. The character length was 8 bits; the sync character was selectable under program control, as well as the modem control leads. It apparently supported idling (sending the sync character); the line could also be set to a mark condition when not transmitting characters. The DUP11 could also be set to discard additional incoming sync characters.

It was intended to interface to Bell 200 series modems (models 201, 208 and 209) and equivalents.

It was a hex card, the M7867; it plugged into an SPC slot. A Berg header on the card connected to a short flat cable which led off to a connector.

Registers

Register Abbreviation Address
Receiver Status Register RxCSR 16xxx0
Receiver Data Buffer Register (read only) RxDBUF 16xxx2
Parameter Status Register (write only) PARCSR 16xxx2
Transmitter Status Register TxCSR 16xxx4
Transmitter Data Buffer Register TxDBUF 16xxx6

16xxx0: Receiver Status Register (RxCSR)

DSCA RING CTS CARR RACT SECRCV DSR SSYNC RDN RDIE DSIE REN SECXMT RTS DTR DSCB
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • DSCA - Data Set Change A; set for any change on Ring, Clear to Send (optionally DSCB lines)
  • RING - Ring Indicator
  • CTS - Clear to Send
  • CARR - Carrier
  • RACT - Receiver Active; set after the first character has been assembled
  • SECRCV - Secondary Receive Data
  • DSR - Data Set Ready
  • SSYNC - Strip Sync; sync characters following the first are discarded - only used with byte-oriented protocols
  • RDN - Receive Done Flag; set when the receive buffer contains an assembled character
  • RDIE - Receive Interrupt Enable; allows an input interrupt when Receive Done is set
  • DSIE - Data Set Interrupt Enable; allows an input interrupt when DSCA is set
  • REN - Receiver Enable; when first set, the receiver looks for synchronization
  • SECXMT - Secondary Transmit Data
  • RTS - Ready to Send
  • DTR - Data Terminal Ready
  • DSCB - Data Set Change B; set for any change on Carrier, Data Set Ready, Secondary Received Data

16xxx2: Receiver Data Buffer Register (RxDBUF)

ERR OVR Rsvd RCRC Rsvd RABO REOM RSOM DDAT
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • ERR - Error
  • OVR - Overrun
  • RCRC - Receiver CRC
  • RABO - Received Abort
  • REOM - End of Received Message
  • RSOM - Start of Received Message
  • RDAT - Received Data Buffer

16xxx2: Parameter Status Register (PARCSR)

DEC Rsvd SEC MD Rsvd CRC INH Rsvd SEC ADDR/RSYNC
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • DEC - DEC Mode
  • SEC MD - Secondary Mode
  • CRC INH - CRC Inhibit
  • SEC ADDR/RSYNC - Secondary Station Address / Receiver Sync
Retrieved from "https://gunkies.org/w/index.php?title=DUP11_synchronous_serial_line_interface&oldid=22155"