Difference between revisions of "Installing 4.3 BSD NFS Wisconsin Unix"

From Computer History Wiki
Jump to: navigation, search
m (→‎Adding an RA81 disk: avoid redir)
 
(16 intermediate revisions by one other user not shown)
Line 1: Line 1:
−
 
 
== Requirements ==
 
== Requirements ==
  
Line 8: Line 7:
 
*A method of extracting the boot file from either the binaries (tar/gzip) or uudecode to extract it from [[boot42|here]].<br>
 
*A method of extracting the boot file from either the binaries (tar/gzip) or uudecode to extract it from [[boot42|here]].<br>
 
*A compiled binary of vax780 from [[SIMH]], along with the vmb.exe again from [[SIMH]].
 
*A compiled binary of vax780 from [[SIMH]], along with the vmb.exe again from [[SIMH]].
 +
*The [[Mkdisttap.pl]] program, you can take the settings from [[Mkdisttap.pl#Quasijarus_0c|Quasijarus]] as the names & block sizes match up.
  
  
Line 16: Line 16:
 
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/rootdump.gz rootdump.gz]<br>
 
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/rootdump.gz rootdump.gz]<br>
 
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/usr.tar.gz usr.tar.gz]<br>
 
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/usr.tar.gz usr.tar.gz]<br>
−
----
+
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/srcsys.tar.gz srcsys.tar.gz]<br>
−
[http://unix-archive.huihoo.org/4BSD/Distributions/4.3BSD/src.tar.gz src.tar.gz]<br>
+
[http://mirror.cc.vt.edu/pub/Ancient_Unix/4BSD/Distributions/thirdparty/UWisc4.3/src.tar.gz src.tar.gz]<br>
−
[http://unix-archive.huihoo.org/4BSD/Distributions/4.3BSD/srcsys.tar.gz srcsys.tar.gz]<br>
+
 
−
[http://unix-archive.huihoo.org/4BSD/Distributions/4.3BSD/stand.gz stand.gz]<br>
+
== Preparing for installation ==
−
[http://unix-archive.huihoo.org/4BSD/Distributions/4.3BSD/vfont.tar.gz vfont.tar.gz]<br><br>
+
 
 +
 
 +
With the files downloaded you will need to uncompress them all and then create the tape file.
 +
 
 +
The following command will decompress the tape files.
 +
<pre>
 +
gzip -d *.gz
 +
</pre>
 +
 
 +
The tape needs to be created with the [[mkdisttap.pl]] program.  Simply run the program and redirect it into a file called uwisc.tap .
 +
 
 +
<pre>
 +
% ./mkdisttap.pl > uwisc.tap
 +
% ls -l uwisc.tap
 +
-rw-r--r--  1 Neozeed  None  74337572 Apr  7 19:40 uwisc.tap
 +
</pre>
 +
 
 +
 
 +
Next you will need the boot program.  I have uploaded a copy onto this wiki in uuencoded format.  To decode it, simply access the [[BootHP|article]], and copy the contents of the quoted text (the begin/end part INCLUDING the begin & end segments) and save it to a text file.  Then you will need to run the uudecode file as follows:
 +
 
 +
<pre>
 +
% ls -l boothp.uue
 +
-rw-r--r--  1 Neozeed  None  10683 Apr  7 20:15 boothp.uue
 +
% uudecode boothp.uue
 +
% ls -l boothp
 +
-rw-------  1 Neozeed  None  7736 Apr  7 20:20 boothp
 +
% file boothp
 +
boothp: data
 +
%
 +
</pre>
 +
 
 +
==  Boot 1. ==
 +
 
 +
We are going to use the following config file to start the first phase of the installation.  Save the following configuration into a file such as 'install.ini'.  Since we are going to boot directly into the miniroot the rq1 disk will hold the installation target.  Since the 'normal' way to install is to install from tape onto the first disk, we will have to add a device file uppon boot for the second disk, and be sure to point the xtr program to the second disk.
 +
 
 +
=== install.ini ===
 +
<pre>
 +
set rq0 dis
 +
set rq1 dis
 +
set rq2 dis
 +
set rq3 dis
 +
set rp0 rp06
 +
att rp0 miniroot
 +
set rp1 rp06
 +
att rp1 rp06.disk
 +
set rp2 dis
 +
set rp3 dis
 +
set rp4 dis
 +
set rp5 dis
 +
set rp6 dis
 +
set rp7 dis
 +
set lpt dis
 +
set rl dis
 +
set tq dis
 +
set tu dis
 +
att ts uwisc.tap
 +
set tti 7b
 +
set tto 7b
 +
load -o boothp 0
 +
d r10 0
 +
d r11 0
 +
run 2
 +
</pre>
 +
 
 +
=== Booting the emulator ===
 +
 
 +
You then simply run the emulator and pass it the config file.  You will be prompted to "overwrite last track" answer y and hit enter.
 +
 
 +
<pre>
 +
% ./vax780 install.ini
 +
 
 +
VAX780 simulator V3.8-1
 +
RP: creating new file
 +
Overwrite last track? [N] y
 +
loading hp(0,0)boot
 +
 
 +
Boot
 +
: hp(0,0)vmunix
 +
290188+89696+102928 start 0x12f8
 +
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
 +
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
 +
real mem  = 8388608
 +
SYSPTSIZE limits number of buffers to 134
 +
avail mem = 7136256
 +
using 134 buffers containing 524288 bytes of memory
 +
mcr0 at tr1
 +
mcr1 at tr2
 +
uba0 at tr3
 +
hk0 at uba0 csr 177440 vec 210, ipl 15
 +
rk0 at hk0 slave 0
 +
rk1 at hk0 slave 1
 +
rk2 at hk0 slave 2
 +
rk3 at hk0 slave 3
 +
uda0 at uba0 csr 172150 vec 774, ipl 15
 +
zs0 at uba0 csr 172520 vec 224, ipl 15
 +
ts0 at zs0 slave 0
 +
dz0 at uba0 csr 160100 vec 300, ipl 15
 +
dz1 at uba0 csr 160110 vec 310, ipl 15
 +
dz2 at uba0 csr 160120 vec 320, ipl 15
 +
dz3 at uba0 csr 160130 vec 330, ipl 15
 +
mba0 at tr8
 +
hp0 at mba0 drive 0
 +
hp1 at mba0 drive 1
 +
Changing root device to hp0a
 +
erase ^?, kill ^U, intr ^C
 +
#
 +
</pre>
 +
 
 +
=== Restoring the rootdump ===
 +
 
 +
From here we are now running from the miniroot.  The next steps are as follows:
 +
 
 +
<pre>
 +
# cd /dev
 +
# ./MAKEDEV hp1
 +
# cd /
 +
# disk=hp1 type=rp06 tape=ts xtr
 +
</pre>
 +
 
 +
This will create a 'device' for the hp1 disk, then run the xtr program to restore the root dump.  Take note that the chgrp & chmod commands are not found, however the install will proceed as normal.
 +
 
 +
<pre>
 +
# cd /dev
 +
# ./MAKEDEV hp1
 +
syntax error
 +
./MAKEDEV: chgrp: not found
 +
./MAKEDEV: chmod: not found
 +
# cd /
 +
# disk=hp1 type=rp06 tape=ts xtr
 +
Build root file system
 +
/dev/rhp1a:    15884 sectors in 38 cylinders of 19 tracks, 22 sectors
 +
        8.1Mb in 3 cyl groups (16 c/g, 3.42Mb/g, 1216 i/g)
 +
super-block backups (for fsck -b#) at:
 +
32, 6752, 13472,
 +
Check the file system
 +
** /dev/rhp1a
 +
** Last Mounted on
 +
** Phase 1 - Check Blocks and Sizes
 +
** Phase 2 - Check Pathnames
 +
** Phase 3 - Check Connectivity
 +
** Phase 4 - Check Reference Counts
 +
** Phase 5 - Check Cyl groups
 +
2 files, 9 used, 7412 free (20 frags, 924 blocks, 0.3% fragmentation)
 +
Rewind tape
 +
Restore the dump image of the root
 +
Warning: ./lost+found: File exists
 +
** /dev/rhp1a
 +
** Last Mounted on /a
 +
** Phase 1 - Check Blocks and Sizes
 +
** Phase 2 - Check Pathnames
 +
** Phase 3 - Check Connectivity
 +
** Phase 4 - Check Reference Counts
 +
** Phase 5 - Check Cyl groups
 +
329 files, 5370 used, 2051 free (11 frags, 255 blocks, 0.1% fragmentation)
 +
Root filesystem extracted
 +
 
 +
If this is an 8650 or 8600, update the console rl02
 +
If this is a 780 or 785, update the floppy
 +
If this is a 730, update the cassette
 +
#
 +
</pre>
 +
 
 +
After this stage, I just sync the disk a few times, then halt the emulator (CONTROL+E) and exit out. Now we are ready for stage two.
 +
 
 +
<pre>
 +
If this is a 730, update the cassette
 +
# sync
 +
# sync
 +
# sync
 +
 
 +
Simulation stopped, PC: 800018A3 (MTPR #0,#12)
 +
sim> q
 +
Goodbye
 +
%
 +
</pre>
 +
 
 +
==  Boot 2. ==
 +
 
 +
Now that the install disk is prepared, we need to use a different config file to reflect us going back to a single disk/tape configuration.  The new configuration is as follows:
 +
 
 +
=== boot.ini ===
 +
<pre>
 +
set rq0 dis
 +
set rq1 dis
 +
set rq2 dis
 +
set rq3 dis
 +
set rp0 rp06
 +
att rp0 rp06.disk
 +
set rp1 dis
 +
set rp2 dis
 +
set rp3 dis
 +
set rp4 dis
 +
set rp5 dis
 +
set rp6 dis
 +
set rp7 dis
 +
set lpt dis
 +
set rl dis
 +
set tq dis
 +
set tu dis
 +
att ts uwisc.tap
 +
set tti 7b
 +
set tto 7b
 +
load -o boothp 0
 +
d r10 0
 +
d r11 0
 +
run 2
 +
</pre>
 +
 
 +
=== Booting the emulator ===
 +
 
 +
Now boot up the emulator with the boot.ini
 +
 
 +
<pre>
 +
% ./vax780  boot.ini
 +
 
 +
VAX780 simulator V3.8-1
 +
loading hp(0,0)boot
 +
 
 +
Boot
 +
: hp(0,0)vmunix
 +
290188+89696+102928 start 0x12f8
 +
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
 +
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
 +
real mem  = 8388608
 +
SYSPTSIZE limits number of buffers to 134
 +
avail mem = 7136256
 +
using 134 buffers containing 524288 bytes of memory
 +
mcr0 at tr1
 +
mcr1 at tr2
 +
uba0 at tr3
 +
hk0 at uba0 csr 177440 vec 210, ipl 15
 +
rk0 at hk0 slave 0
 +
rk1 at hk0 slave 1
 +
rk2 at hk0 slave 2
 +
rk3 at hk0 slave 3
 +
uda0 at uba0 csr 172150 vec 774, ipl 15
 +
zs0 at uba0 csr 172520 vec 224, ipl 15
 +
ts0 at zs0 slave 0
 +
dz0 at uba0 csr 160100 vec 300, ipl 15
 +
dz1 at uba0 csr 160110 vec 310, ipl 15
 +
dz2 at uba0 csr 160120 vec 320, ipl 15
 +
dz3 at uba0 csr 160130 vec 330, ipl 15
 +
mba0 at tr8
 +
hp0 at mba0 drive 0
 +
Changing root device to hp0a
 +
Automatic reboot in progress...
 +
Tue Apr  7 13:29:38 PDT 1987
 +
/dev/hp0a: 329 files, 5370 used, 2051 free (11 frags, 255 blocks, 0.1% fragmenta
 +
tion)
 +
/dev/rhp0h: CANNOT READ: BLK 16
 +
/dev/rhp0h: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
 +
Automatic reboot failed... help!
 +
erase ^?, kill ^U, intr ^C
 +
#
 +
</pre>
 +
 
 +
=== Preparing the disk ===
 +
 
 +
Now we have to prep the machine for both the tape, and the type of disk.  Type in the following commands.
 +
 
 +
<pre>
 +
# disk=hp
 +
# name=hp0g;type=rp06
 +
# cd /dev
 +
# sh ./MAKEDEV ts0;sync
 +
# cd /
 +
# newfs $name $type
 +
</pre>
 +
 
 +
The output will be like this:
 +
 
 +
<pre>
 +
# newfs $name $type
 +
Warning: 154 sector(s) in last cylinder unallocated
 +
/dev/rhp0g:    291192 sectors in 697 cylinders of 19 tracks, 22 sectors
 +
        149.1Mb in 44 cyl groups (16 c/g, 3.42Mb/g, 1536 i/g)
 +
super-block backups (for fsck -b#) at:
 +
32, 6744, 13456, 20168, 26880, 33592, 40304, 47016, 53728, 60440,
 +
67152, 73864, 80576, 87288, 94000, 100712, 107424, 114136, 120848, 127560,
 +
134272, 140984, 147696, 154408, 161120, 167832, 174544, 181256, 187968, 194680,
 +
 
 +
201392, 208104, 214048, 220760, 227472, 234184, 240896, 247608, 254320, 261032,
 +
 
 +
267744, 274456, 281168, 287880,
 +
</pre>
 +
 
 +
 
 +
=== Restoring the usr slice ===
 +
 
 +
The disk's /usr slice will not have been formatted.  We can not go ahead and mount it, and restore the /usr files.  Then we unmount the slice, and run fsck to make sure everything is ok.
 +
 
 +
<pre>
 +
# mount /dev/$name /usr
 +
# cd /usr
 +
# mkdir sys
 +
# mt rew
 +
# mt fsf 3
 +
# tar xpbf 20 /dev/rmt12
 +
# cd sys
 +
# mt fsf
 +
# tar xpbf 20 /dev/rmt12
 +
# cd /
 +
# umount /dev/$name
 +
# fsck /dev/r$name
 +
</pre>
 +
 
 +
Likewise, the output should be similar to this:
 +
 
 +
<pre>
 +
# mount /dev/$name /usr
 +
# cd /usr
 +
# mkdir sys
 +
# mt rew
 +
# mt fsf 3
 +
# tar xpbf 20 /dev/rmt12
 +
# cd sys
 +
# mt fsf
 +
# tar xpbf 20 /dev/rmt12
 +
# cd /
 +
# umount /dev/$name
 +
# fsck /dev/r$name
 +
** /dev/rhp0g
 +
** Last Mounted on /usr
 +
** Phase 1 - Check Blocks and Sizes
 +
** Phase 2 - Check Pathnames
 +
DIRECTORY /man/cat1: LENGTH 5140 NOT MULTIPLE OF 512
 +
ADJUST? y
 +
 
 +
DIRECTORY /man/man0: LENGTH 532 NOT MULTIPLE OF 512
 +
ADJUST? y
 +
 
 +
** Phase 3 - Check Connectivity
 +
** Phase 4 - Check Reference Counts
 +
** Phase 5 - Check Cyl groups
 +
5131 files, 60483 used, 212723 free (627 frags, 26512 blocks, 0.2% fragmentation)
 +
 
 +
***** FILE SYSTEM WAS MODIFIED *****
 +
</pre>
 +
 
 +
There will always be some errors it would seem....  Also this is more of a dump of an existing system, not a 'distribution' tape, so there are some things we have to take care of.
 +
 
 +
The password file needs to be 'fixed' because I don't have the root password....
 +
 
 +
<pre>
 +
root::0:1:The Not Ready for Prime Time Super User:/:/bin/csh
 +
daemon:*:1:1:The devil himself:/:
 +
operator:*:5:5:Operator:/usr/operator:/bin/csh
 +
tty::4:4:Which tty am I:/bin:/usr/bin/tty
 +
news:vXHPueUygRELQ:6:6:The News:/usr/lib/news:/bin/csh
 +
uucp:GbeWaSRwdvDCE:66:66:UNIX-to-UNIX Copy:/usr/spool/uucppublic:/usr/lib/uucp/uucico
 +
tadl:XyGpEqJu78.Rg:1433:10:Tad Lebeck,2289C,27950,2515517:/usr/staff/tadl:/bin/csh
 +
nobody:nopass:32767:32767:Nonexistent user:/nonexistent:/dev/null
 +
</pre>
 +
 
 +
simply catting that into /etc/passwd should do the trick if you have a 'console' that you can paste text into....!
 +
 
 +
The next thing that will have to be fixed is the fstab.
 +
<pre>
 +
/dev/hp0a / 4.2 rw,noquota 1 1
 +
/dev/hp0g /usr 4.2 rw,noquota 1 2
 +
</pre>
 +
 
 +
Again cat that into /etc/fstab .
 +
 
 +
Finally let's add the DZ device files, and the ptys...
 +
 
 +
<pre>
 +
# cd /dev
 +
# sh ./MAKEDEV dz0
 +
# sh ./MAKEDEV pty0
 +
</pre>
 +
 
 +
== First Multiuser Boot ==
 +
 
 +
Now we can just re-run the last command, and we should boot multiuser!  By default there is no root password.  Also the system will run fsck uppon boot, so depending on your host computer this could take a while.
 +
 
 +
 
 +
<pre>
 +
% ./vax780 boot.ini
 +
 
 +
VAX780 simulator V3.8-1
 +
loading hp(0,0)boot
 +
 
 +
Boot
 +
: hp(0,0)vmunix
 +
290188+89696+102928 start 0x12f8
 +
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
 +
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
 +
real mem  = 8388608
 +
SYSPTSIZE limits number of buffers to 134
 +
avail mem = 7136256
 +
using 134 buffers containing 524288 bytes of memory
 +
mcr0 at tr1
 +
mcr1 at tr2
 +
uba0 at tr3
 +
hk0 at uba0 csr 177440 vec 210, ipl 15
 +
rk0 at hk0 slave 0
 +
rk1 at hk0 slave 1
 +
rk2 at hk0 slave 2
 +
rk3 at hk0 slave 3
 +
uda0 at uba0 csr 172150 vec 774, ipl 15
 +
zs0 at uba0 csr 172520 vec 224, ipl 15
 +
ts0 at zs0 slave 0
 +
dz0 at uba0 csr 160100 vec 300, ipl 15
 +
dz1 at uba0 csr 160110 vec 310, ipl 15
 +
dz2 at uba0 csr 160120 vec 320, ipl 15
 +
dz3 at uba0 csr 160130 vec 330, ipl 15
 +
mba0 at tr8
 +
hp0 at mba0 drive 0
 +
Changing root device to hp0a
 +
Automatic reboot in progress...
 +
Tue Apr  7 13:38:51 PDT 1987
 +
/dev/hp0a: 381 files, 5371 used, 2050 free (10 frags, 255 blocks, 0.1% fragmenta
 +
tion)
 +
/dev/rhp0g: 5131 files, 60483 used, 212723 free (627 frags, 26512 blocks, 0.2% f
 +
ragmentation)
 +
Tue Apr  7 13:38:54 PDT 1987
 +
/dev/hp0a mounted on /
 +
/dev/hp0g mounted on /usr
 +
starting rpc daemons: portmap rpcd.
 +
starting system logger
 +
starting local deamons: routed sendmail biod.
 +
preserving editor files
 +
clearing /tmp
 +
standard daemons: update cron.
 +
starting network daemons: inetd printer.
 +
Tue Apr  7 13:38:57 PDT 1987
 +
 
 +
 
 +
Wisconsin UNIX (myname console)
 +
4.3+NFS > V.*
 +
 
 +
login:
 +
</pre>
 +
 
 +
Now we've booted up and you can login as root!
 +
 
 +
<pre>
 +
Wisconsin UNIX (myname console)
 +
4.3+NFS > V.*
 +
 
 +
login: root
 +
Last login: Mon Jan 12 12:44:40 on console
 +
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
 +
 
 +
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
 +
 
 +
 
 +
                        4.3+NFS Wisconsin Unix
 +
 
 +
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
 +
 
 +
You have mail.
 +
Don't login as root, use su
 +
myname#
 +
</pre>
 +
 
 +
 
 +
=== Enabling remote users ===
 +
 
 +
Shutdown the OS, and add the following lines into the boot.ini (just make sure they are above the boot command or it'll not work correctly..). This will allow for 8 users to connect on tcp port 8888.
 +
 
 +
<pre>
 +
set dz lines=8
 +
att dz 8888
 +
set dz 7b
 +
</pre>
 +
 
 +
I would also recommend to windows users, either [[putty]], or [[syncterm]].  The default telnet client sucks.
 +
 
 +
==== fixing if_de.c ====
 +
On my SLiRP builds, I've noticed that the interface just generates errors, but it should work.  It was easier to 'fix' the BSD device driver...
 +
 
 +
So in the derecv procedure apply the following fix:
 +
 
 +
<pre>
 +
        /* check for errors */
 +
        if(1==2){
 +
/**    if ((rp->r_flags & (RFLG_ERRS|RFLG_FRAM|RFLG_OFLO|RFLG_CRC)) ||
 +
            (rp->r_flags&(RFLG_STP|RFLG_ENP)) != (RFLG_STP|RFLG_ENP) ||
 +
            (rp->r_lenerr & (RERR_BUFL|RERR_UBTO|RERR_NCHN)) ||
 +
            len < ETHERMIN || len > ETHERMTU) {
 +
            ***/
 +
</pre>
  
−
----
+
== Adding an RA81 disk ==
 +
I've found the default disktab entry for the [[RA81 disk drive|RA81]] disk to be unsatisfactory.  I've found this one to be much more agreeable:
  
−
Life interrupts again... I'll have to finish later.. but it's just like a 4.3 BSD install.
+
<pre>
 +
ra81|RA81|DEC RA81 Winchester:\
 +
        :ty=winchester:ns#51:nt#14:nc#1248:\
 +
        :dt=MSCP:\
 +
        :pa#15884:oa#0:ba#8192:fa#1024:\
 +
        :pb#66880:ob#16422:bb#8192:fb#1024:tb=swap:\
 +
        :pc#891072:oc#0:bc#8192:fc#1024:\
 +
        :pd#15884:od#375564:bd#4096:fd#512:\
 +
        :pe#307200:oe#391986:be#8192:fe#1024:\
 +
        :pf#191352:of#699720:bf#8192:ff#1024:\
 +
        :pg#515508:og#375564:bg#8192:fg#1024:\
 +
        :ph#291346:oh#83538:bh#8192:fh#1024:
 +
</pre>
 +
[[Category:SIMH Tutorials]]

Latest revision as of 17:46, 28 October 2020

Requirements

You will need the following materials to put together a 4.3 BSD+NFS Wisconsin Unix installation:

  • A working perl interpeter to make the tape images.
  • A copy of gzip.
  • A method of extracting the boot file from either the binaries (tar/gzip) or uudecode to extract it from here.
  • A compiled binary of vax780 from SIMH, along with the vmb.exe again from SIMH.
  • The Mkdisttap.pl program, you can take the settings from Quasijarus as the names & block sizes match up.


You will need the following files from any 4 BSD archive from the 4.3BSD directory. I have used the files from mirror.cc.vt.edu. You can use whatever method you like to download them, wget, a web browser etc..

stand.gz
miniroot.gz
rootdump.gz
usr.tar.gz
srcsys.tar.gz
src.tar.gz

Preparing for installation

With the files downloaded you will need to uncompress them all and then create the tape file.

The following command will decompress the tape files. 

gzip -d *.gz

The tape needs to be created with the mkdisttap.pl program. Simply run the program and redirect it into a file called uwisc.tap . 

% ./mkdisttap.pl > uwisc.tap
% ls -l uwisc.tap
-rw-r--r--  1 Neozeed  None  74337572 Apr  7 19:40 uwisc.tap


Next you will need the boot program. I have uploaded a copy onto this wiki in uuencoded format. To decode it, simply access the article, and copy the contents of the quoted text (the begin/end part INCLUDING the begin & end segments) and save it to a text file. Then you will need to run the uudecode file as follows: 

% ls -l boothp.uue
-rw-r--r--  1 Neozeed  None  10683 Apr  7 20:15 boothp.uue
% uudecode boothp.uue
% ls -l boothp
-rw-------  1 Neozeed  None  7736 Apr  7 20:20 boothp
% file boothp
boothp: data
%

Boot 1.

We are going to use the following config file to start the first phase of the installation. Save the following configuration into a file such as 'install.ini'. Since we are going to boot directly into the miniroot the rq1 disk will hold the installation target. Since the 'normal' way to install is to install from tape onto the first disk, we will have to add a device file uppon boot for the second disk, and be sure to point the xtr program to the second disk.

install.ini

set rq0 dis
set rq1 dis
set rq2 dis
set rq3 dis
set rp0 rp06
att rp0 miniroot
set rp1 rp06
att rp1 rp06.disk
set rp2 dis
set rp3 dis
set rp4 dis
set rp5 dis
set rp6 dis
set rp7 dis
set lpt dis
set rl dis
set tq dis
set tu dis
att ts uwisc.tap
set tti 7b
set tto 7b
load -o boothp 0
d r10 0
d r11 0
run 2

Booting the emulator

You then simply run the emulator and pass it the config file. You will be prompted to "overwrite last track" answer y and hit enter. 

% ./vax780 install.ini

VAX780 simulator V3.8-1
RP: creating new file
Overwrite last track? [N] y
loading hp(0,0)boot

Boot
: hp(0,0)vmunix
290188+89696+102928 start 0x12f8
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 134
avail mem = 7136256
using 134 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
mba0 at tr8
hp0 at mba0 drive 0
hp1 at mba0 drive 1
Changing root device to hp0a
erase ^?, kill ^U, intr ^C
#

Restoring the rootdump

From here we are now running from the miniroot. The next steps are as follows: 

# cd /dev
# ./MAKEDEV hp1
# cd /
# disk=hp1 type=rp06 tape=ts xtr

This will create a 'device' for the hp1 disk, then run the xtr program to restore the root dump. Take note that the chgrp & chmod commands are not found, however the install will proceed as normal. 

# cd /dev
# ./MAKEDEV hp1
syntax error
./MAKEDEV: chgrp: not found
./MAKEDEV: chmod: not found
# cd /
# disk=hp1 type=rp06 tape=ts xtr
Build root file system
/dev/rhp1a:     15884 sectors in 38 cylinders of 19 tracks, 22 sectors
        8.1Mb in 3 cyl groups (16 c/g, 3.42Mb/g, 1216 i/g)
super-block backups (for fsck -b#) at:
 32, 6752, 13472,
Check the file system
** /dev/rhp1a
** Last Mounted on
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2 files, 9 used, 7412 free (20 frags, 924 blocks, 0.3% fragmentation)
Rewind tape
Restore the dump image of the root
Warning: ./lost+found: File exists
** /dev/rhp1a
** Last Mounted on /a
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
329 files, 5370 used, 2051 free (11 frags, 255 blocks, 0.1% fragmentation)
Root filesystem extracted

If this is an 8650 or 8600, update the console rl02
If this is a 780 or 785, update the floppy
If this is a 730, update the cassette
#

After this stage, I just sync the disk a few times, then halt the emulator (CONTROL+E) and exit out. Now we are ready for stage two. 

If this is a 730, update the cassette
# sync
# sync
# sync

Simulation stopped, PC: 800018A3 (MTPR #0,#12)
sim> q
Goodbye
%

Boot 2.

Now that the install disk is prepared, we need to use a different config file to reflect us going back to a single disk/tape configuration. The new configuration is as follows:

boot.ini

set rq0 dis
set rq1 dis
set rq2 dis
set rq3 dis
set rp0 rp06
att rp0 rp06.disk
set rp1 dis
set rp2 dis
set rp3 dis
set rp4 dis
set rp5 dis
set rp6 dis
set rp7 dis
set lpt dis
set rl dis
set tq dis
set tu dis
att ts uwisc.tap
set tti 7b
set tto 7b
load -o boothp 0
d r10 0
d r11 0
run 2

Booting the emulator

Now boot up the emulator with the boot.ini 

% ./vax780  boot.ini

VAX780 simulator V3.8-1
loading hp(0,0)boot

Boot
: hp(0,0)vmunix
290188+89696+102928 start 0x12f8
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 134
avail mem = 7136256
using 134 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
mba0 at tr8
hp0 at mba0 drive 0
Changing root device to hp0a
Automatic reboot in progress...
Tue Apr  7 13:29:38 PDT 1987
/dev/hp0a: 329 files, 5370 used, 2051 free (11 frags, 255 blocks, 0.1% fragmenta
tion)
/dev/rhp0h: CANNOT READ: BLK 16
/dev/rhp0h: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Automatic reboot failed... help!
erase ^?, kill ^U, intr ^C
#

Preparing the disk

Now we have to prep the machine for both the tape, and the type of disk. Type in the following commands. 

# disk=hp
# name=hp0g;type=rp06
# cd /dev
# sh ./MAKEDEV ts0;sync
# cd /
# newfs $name $type

The output will be like this: 

# newfs $name $type
Warning: 154 sector(s) in last cylinder unallocated
/dev/rhp0g:     291192 sectors in 697 cylinders of 19 tracks, 22 sectors
        149.1Mb in 44 cyl groups (16 c/g, 3.42Mb/g, 1536 i/g)
super-block backups (for fsck -b#) at:
 32, 6744, 13456, 20168, 26880, 33592, 40304, 47016, 53728, 60440,
 67152, 73864, 80576, 87288, 94000, 100712, 107424, 114136, 120848, 127560,
 134272, 140984, 147696, 154408, 161120, 167832, 174544, 181256, 187968, 194680,

 201392, 208104, 214048, 220760, 227472, 234184, 240896, 247608, 254320, 261032,

 267744, 274456, 281168, 287880,


Restoring the usr slice

The disk's /usr slice will not have been formatted. We can not go ahead and mount it, and restore the /usr files. Then we unmount the slice, and run fsck to make sure everything is ok. 

# mount /dev/$name /usr
# cd /usr
# mkdir sys
# mt rew
# mt fsf 3
# tar xpbf 20 /dev/rmt12
# cd sys
# mt fsf
# tar xpbf 20 /dev/rmt12
# cd /
# umount /dev/$name
# fsck /dev/r$name

Likewise, the output should be similar to this: 

# mount /dev/$name /usr
# cd /usr
# mkdir sys
# mt rew
# mt fsf 3
# tar xpbf 20 /dev/rmt12
# cd sys
# mt fsf
# tar xpbf 20 /dev/rmt12
# cd /
# umount /dev/$name
# fsck /dev/r$name
** /dev/rhp0g
** Last Mounted on /usr
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
DIRECTORY /man/cat1: LENGTH 5140 NOT MULTIPLE OF 512
ADJUST? y

DIRECTORY /man/man0: LENGTH 532 NOT MULTIPLE OF 512
ADJUST? y

** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
5131 files, 60483 used, 212723 free (627 frags, 26512 blocks, 0.2% fragmentation)

***** FILE SYSTEM WAS MODIFIED *****

There will always be some errors it would seem.... Also this is more of a dump of an existing system, not a 'distribution' tape, so there are some things we have to take care of.

The password file needs to be 'fixed' because I don't have the root password.... 

root::0:1:The Not Ready for Prime Time Super User:/:/bin/csh
daemon:*:1:1:The devil himself:/:
operator:*:5:5:Operator:/usr/operator:/bin/csh
tty::4:4:Which tty am I:/bin:/usr/bin/tty
news:vXHPueUygRELQ:6:6:The News:/usr/lib/news:/bin/csh
uucp:GbeWaSRwdvDCE:66:66:UNIX-to-UNIX Copy:/usr/spool/uucppublic:/usr/lib/uucp/uucico
tadl:XyGpEqJu78.Rg:1433:10:Tad Lebeck,2289C,27950,2515517:/usr/staff/tadl:/bin/csh
nobody:nopass:32767:32767:Nonexistent user:/nonexistent:/dev/null

simply catting that into /etc/passwd should do the trick if you have a 'console' that you can paste text into....!

The next thing that will have to be fixed is the fstab. 

/dev/hp0a / 4.2 rw,noquota 1 1
/dev/hp0g /usr 4.2 rw,noquota 1 2

Again cat that into /etc/fstab .

Finally let's add the DZ device files, and the ptys... 

# cd /dev
# sh ./MAKEDEV dz0
# sh ./MAKEDEV pty0

First Multiuser Boot

Now we can just re-run the last command, and we should boot multiuser! By default there is no root password. Also the system will run fsck uppon boot, so depending on your host computer this could take a while. 


% ./vax780 boot.ini

VAX780 simulator V3.8-1
loading hp(0,0)boot

Boot
: hp(0,0)vmunix
290188+89696+102928 start 0x12f8
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986
    tadl@brie:/usr/src/bsd/4.3/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 134
avail mem = 7136256
using 134 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
mba0 at tr8
hp0 at mba0 drive 0
Changing root device to hp0a
Automatic reboot in progress...
Tue Apr  7 13:38:51 PDT 1987
/dev/hp0a: 381 files, 5371 used, 2050 free (10 frags, 255 blocks, 0.1% fragmenta
tion)
/dev/rhp0g: 5131 files, 60483 used, 212723 free (627 frags, 26512 blocks, 0.2% f
ragmentation)
Tue Apr  7 13:38:54 PDT 1987
/dev/hp0a mounted on /
/dev/hp0g mounted on /usr
starting rpc daemons: portmap rpcd.
starting system logger
starting local deamons: routed sendmail biod.
preserving editor files
clearing /tmp
standard daemons: update cron.
starting network daemons: inetd printer.
Tue Apr  7 13:38:57 PDT 1987


Wisconsin UNIX (myname console)
4.3+NFS > V.*

login:

Now we've booted up and you can login as root! 

Wisconsin UNIX (myname console)
4.3+NFS > V.*

login: root
Last login: Mon Jan 12 12:44:40 on console
4.3 BSD UNIX #3: Mon Dec 29 11:54:56 CST 1986

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=


                         4.3+NFS Wisconsin Unix

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

You have mail.
Don't login as root, use su
myname#


Enabling remote users

Shutdown the OS, and add the following lines into the boot.ini (just make sure they are above the boot command or it'll not work correctly..). This will allow for 8 users to connect on tcp port 8888. 

set dz lines=8
att dz 8888
set dz 7b

I would also recommend to windows users, either putty, or syncterm. The default telnet client sucks.

fixing if_de.c

On my SLiRP builds, I've noticed that the interface just generates errors, but it should work. It was easier to 'fix' the BSD device driver...

So in the derecv procedure apply the following fix: 

        /* check for errors */
        if(1==2){
/**     if ((rp->r_flags & (RFLG_ERRS|RFLG_FRAM|RFLG_OFLO|RFLG_CRC)) ||
            (rp->r_flags&(RFLG_STP|RFLG_ENP)) != (RFLG_STP|RFLG_ENP) ||
            (rp->r_lenerr & (RERR_BUFL|RERR_UBTO|RERR_NCHN)) ||
            len < ETHERMIN || len > ETHERMTU) {
            ***/

Adding an RA81 disk

I've found the default disktab entry for the RA81 disk to be unsatisfactory. I've found this one to be much more agreeable: 

ra81|RA81|DEC RA81 Winchester:\
        :ty=winchester:ns#51:nt#14:nc#1248:\
        :dt=MSCP:\
        :pa#15884:oa#0:ba#8192:fa#1024:\
        :pb#66880:ob#16422:bb#8192:fb#1024:tb=swap:\
        :pc#891072:oc#0:bc#8192:fc#1024:\
        :pd#15884:od#375564:bd#4096:fd#512:\
        :pe#307200:oe#391986:be#8192:fe#1024:\
        :pf#191352:of#699720:bf#8192:ff#1024:\
        :pg#515508:og#375564:bg#8192:fg#1024:\
        :ph#291346:oh#83538:bh#8192:fh#1024:
Retrieved from "https://gunkies.org/w/index.php?title=Installing_4.3_BSD_NFS_Wisconsin_Unix&oldid=22622"