DUP11 synchronous serial line interface

DUP11 M7867 board

The DUP11 is an early synchronous serial line interface for the UNIBUS. It was basically a DU11 with CRC computation in hardware. Like the earlier DU11, it used programmed I/O (with separate receive and transmit interrupts) to transfer data; it was double-buffered for both input and output. It could operate in either half-duplex or full-duplex, at baud rates up to 9.6K bits/second.

Both byte-oriented (e.g. DDCMP, BISYNC) and bit-oriented (e.g. SDLC, HDLC) protocols were supported; for error detection, a variety of CRC algorithms, depending on the protocol in use on the line, were supported. The character length was 8 bits; the sync character was selectable under program control, as well as the modem control leads. It apparently supported idling (sending the sync character); the line could also be set to a mark condition when not transmitting characters. The DUP11 could also be set to discard additional incoming sync characters.

It was intended to interface to Bell 200 series modems (models 201, 208 and 209) and equivalents.

It was a hex card, the M7867; it plugged into an SPC slot. A Berg header on the card connected to a short flat cable which led off to a connector.

Registers

Register	Abbreviation	Address
Receiver Status Register	RxCSR	16xxx0
Receiver Data Buffer Register (read only)	RxDBUF	16xxx2
Parameter Status Register (write only)	PARCSR	16xxx2
Transmitter Status Register	TxCSR	16xxx4
Transmitter Data Buffer Register	TxDBUF	16xxx6

16xxx0: Receiver Status Register (RxCSR)

DSCA	RING	CTS	CARR	RACT	SECRCV	DSR	SSYNC	RDN	RDIE	DSIE	REN	SECXMT	RTS	DTR	DSCB
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• DSCA - Data Set Change A; set for any change on Ring, Clear to Send (optionally DSCB lines)
• RING - Ring Indicator
• CTS - Clear to Send
• CARR - Carrier
• RACT - Receiver Active; set after the first character has been assembled
• SECRCV - Secondary Receive Data
• DSR - Data Set Ready
• SSYNC - Strip Sync; sync characters following the first are discarded - only used with byte-oriented protocols
• RDN - Receive Done Flag; set when the receive buffer contains an assembled character
• RDIE - Receive Interrupt Enable; allows an input interrupt when Receive Done is set
• DSIE - Data Set Interrupt Enable; allows an input interrupt when DSCA is set
• REN - Receiver Enable; when first set, the receiver looks for synchronization
• SECXMT - Secondary Transmit Data
• RTS - Ready to Send
• DTR - Data Terminal Ready
• DSCB - Data Set Change B; set for any change on Carrier, Data Set Ready, Secondary Received Data

16xxx2: Receiver Data Buffer Register (RxDBUF)

ERR	OVR	Rsvd	RCRC	Rsvd	RABO	REOM	RSOM	DDAT
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• ERR - Error
• OVR - Overrun
• RCRC - Receiver CRC
• RABO - Received Abort
• REOM - End of Received Message
• RSOM - Start of Received Message
• RDAT - Received Data Buffer

16xxx2: Parameter Status Register (PARCSR)

DEC	Rsvd		SEC MD	Rsvd		CRC INH	Rsvd	SEC ADDR/RSYNC
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• DEC - DEC Mode
• SEC MD - Secondary Mode
• CRC INH - CRC Inhibit
• SEC ADDR/RSYNC - Secondary Station Address / Receiver Sync

16xxx4: Transmitter Status Register (TxCSR)

DLT	MTDO	MCLK	MMSB	MMSA	MID	TACT	DRST	TDN	TIE	Unused	SEND	HDFD	Unused
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• DLT - Transmitter Data Late Error
• MTDO - Maintenance Transmit Data Out
• MCLK - Maintenance Clock
• MMSB - Maintenance Mode Select B
• MMSA - Maintenance Mode Select A
• MID - Maintenance Input Data
• TACT - Transmitter Active
• DRST - Device Reset
• TDN - Transmitter Done; set when the Transmitter Data Buffer id ready for the next character
• TIE - Transmitter Interrupt Enable; allows a transmit interrupt when Transmit Done is set
• SEND - Send; enables the transmitter logic
• HDFD - Half-Duplex/Full-Duplex

16xxx6: Transmitter Data Buffer Register (TxDBUF)

Unused	RCRCIN	Unused	TCRCIN	MTIM	TABO	TEOM	TSOM	TDBUF
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• RCRCIN - Receiver CRC Internal Maint
• TCRCIN - Transmitter CRC Internal Maint
• MTIM - Maintenance Timer
• TABO - Transmit Abort
• TEOM - Transmit End of Message
• TSOM - Transmit Start of Message
• TDBUF - Transmitter Data Buffer

See also

• DP11-A synchronous serial line interface

External links

• DUP11 bit synchronous interface user's manual (EK-DUP11-OP-001)
• DUP11 Bit Synchronous Interface User's Manual (EK-DUP11-OP-002)
• DUP11 Bit Synchronous Interface Maintenance Manual (EK-DUP11-MM-003)