Difference between revisions of "H765 Power System"
m (Avoid redir after rename) |
m (New cat) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | The '''H765 Power System''' is a modular [[power supply]] system from [[Digital Equipment Corporation|DEC]], used in the [[BA11-K mounting box]]. In addition to [[main memory]] and [[device controller]]s on other [[PDP-11]]'s, the BA11-K was used to hold [[PDP-11/04]] and [[PDP-11/34]] [[Central Processing Unit|CPU]]'s. | + | The '''H765 Power System''' is a modular [[power supply]] system from [[Digital Equipment Corporation|DEC]], used in the [[BA11-K mounting box]] and variants thereof. In addition to [[main memory]] and [[device controller]]s on other [[PDP-11]]'s, the BA11-K was used to hold [[PDP-11/04]] and [[PDP-11/34]] [[Central Processing Unit|CPU]]'s. |
| − | The H765 supplies | + | The main [[transformer]] in the H765 supplies 20-30V [[Alternating current|AC]] to several [[DEC standard modular regulators]] (up to four, in spaces numbered '1' through '4') mounted in the H765, which provide other voltages such as +5V [[Direct current|DC]] to the [[backplane]]s in the mounting box. |
| − | + | Generally the [[power harness]] supports only a fixed arrangement as to which regulator can be in which spaces; e.g. the BA11-K harness mandates that #2 and #3 hold [[H744 +5V Regulator]]s, #1 holds an [[H745 -15V Regulator]], and #4 may hold an [[H754 +20V, -5V Regulator]]. | |
| + | |||
| + | [[Image:DEC 7010138 Harness.jpg|thumb|right|300px|70-10138 harness]] | ||
| + | |||
| + | A [[DEC Power Line Monitor|54-11086 board]] in the H765 supplies a modest amount of +15V DC power to various backplanes mounted in the BA11-K, along with a [[line time clock]] signal, and AC and DC 'power OK' signals. A special [[DEC part number|70-10138]] harness is used to connect the edge finger connectors of the 54-11086 to the power distribution board in the BA11-K. | ||
| − | + | The BA11-K harness used [[DEC power distribution connectors]] to provide power to standard backplanes; it normally used the [[DEC standard power wire colour coding]]. | |
| − | When the BA11-K is used in custom configurations to hold systems (such as the [[MJ11 memory system]] and [[MK11 memory system]]), other regulator configurations may be used | + | When the BA11-K box is used in custom configurations to hold other sub-systems (such as the [[MJ11 memory system|MJ11]] and [[MK11 memory system]]s), other regulator configurations may be used (e.g. the MJ11 calls for two H744's and two H754's), along with a custom main harness, and harness to the 5411086. |
| + | |||
| + | The H765 runs off standard wall AC; it can be [[jumper]]ed to use either 110V or 220V supply. It supported the standard DEC [[Remote Switching Control Bus]], so it could be turned off and on from a power switch elsewhere. | ||
| − | + | ==Issues== | |
| − | + | Some components on the 54-11086 board are not protected by a [[fuse]]; if they fail 'closed', since AC to that board enters through contacts on the edge connector, those contacts may be damaged. | |
==See also== | ==See also== | ||
| Line 17: | Line 23: | ||
* [[H742 Power Supply]] | * [[H742 Power Supply]] | ||
| − | [[Category: DEC | + | [[Category: DEC Power Supplies]] |
Latest revision as of 14:39, 10 July 2023
The H765 Power System is a modular power supply system from DEC, used in the BA11-K mounting box and variants thereof. In addition to main memory and device controllers on other PDP-11's, the BA11-K was used to hold PDP-11/04 and PDP-11/34 CPU's.
The main transformer in the H765 supplies 20-30V AC to several DEC standard modular regulators (up to four, in spaces numbered '1' through '4') mounted in the H765, which provide other voltages such as +5V DC to the backplanes in the mounting box.
Generally the power harness supports only a fixed arrangement as to which regulator can be in which spaces; e.g. the BA11-K harness mandates that #2 and #3 hold H744 +5V Regulators, #1 holds an H745 -15V Regulator, and #4 may hold an H754 +20V, -5V Regulator.
A 54-11086 board in the H765 supplies a modest amount of +15V DC power to various backplanes mounted in the BA11-K, along with a line time clock signal, and AC and DC 'power OK' signals. A special 70-10138 harness is used to connect the edge finger connectors of the 54-11086 to the power distribution board in the BA11-K.
The BA11-K harness used DEC power distribution connectors to provide power to standard backplanes; it normally used the DEC standard power wire colour coding.
When the BA11-K box is used in custom configurations to hold other sub-systems (such as the MJ11 and MK11 memory systems), other regulator configurations may be used (e.g. the MJ11 calls for two H744's and two H754's), along with a custom main harness, and harness to the 5411086.
The H765 runs off standard wall AC; it can be jumpered to use either 110V or 220V supply. It supported the standard DEC Remote Switching Control Bus, so it could be turned off and on from a power switch elsewhere.
Issues
Some components on the 54-11086 board are not protected by a fuse; if they fail 'closed', since AC to that board enters through contacts on the edge connector, those contacts may be damaged.
