Difference between revisions of "BA11-E Mounting Box"
(A good start) |
m (New cat) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | The '''BA11-E mounting box''' was one of the two earliest earliest standard [[system unit]] [[backplane]] [[mounting box]] produced by [[Digital Equipment Corporation|DEC]], along with the [[BA11-C Mounting Box | + | The '''BA11-E mounting box''' was one of the two earliest earliest standard [[system unit]] [[backplane]] [[mounting box]] produced by [[Digital Equipment Corporation|DEC]], along with the [[BA11-C Mounting Box]]. |
| − | It came in two variants, the rack-mounted BA11-ES (including Tilt and Lock chassis slides), and the table-top BA11-EC. The rack-mounted ones were usually mounted in the [[H960 rack|H960]] series of 19"-wide racks, which provided 63" of vertical mounting space, divided into units of 10-1/2". The 10-1/2" tall BA11-E mounting box was designed for these spaces | + | It was created for the expansion box role (hence the -E variant suffix) with the early [[PDP-11]]'s (particularly the [[PDP-11/20]]). In that role, it was used to hold extra [[core memory|core]] [[main memory]] systems (each in their own custom system unit) and other devices, and had a blank front panel. |
| + | |||
| + | It came in two variants, the rack-mounted '''BA11-ES''' (including Tilt and Lock chassis slides), and the table-top '''BA11-EC'''. The rack-mounted ones were usually mounted in the [[H960 rack|H960]] series of 19"-wide racks, which provided 63" of vertical mounting space, divided into units of 10-1/2". The 10-1/2" tall BA11-E mounting box was designed for these spaces | ||
A BA11-E could hold up to six standard size (4-slot) system units; these were mounted transversely, facing down. They were generally mounted with the [[DEC edge connector contact identification|A-row connectors]] at the left-hand side. | A BA11-E could hold up to six standard size (4-slot) system units; these were mounted transversely, facing down. They were generally mounted with the [[DEC edge connector contact identification|A-row connectors]] at the left-hand side. | ||
| − | A set of four cooling fans was also mounted at the left-hand side of the box, to provide air-flow to the boards and [[power supply]]. Since the fans intruded into the space 'above' the backplanes, the latter could not hold [[DEC card form factor|hex]] cards, only quads, plus a single [[DEC card form factor|extended length]] card. | + | A set of four cooling fans was also mounted at the left-hand side of the box, to provide air-flow to the boards and [[power supply]]. Since the fans intruded into the space 'above' (actually, to the side of, in the BA11-E - DEC location nomenclature assumes that the boards have their side edge at the top) the backplanes, the latter could not hold [[DEC card form factor|hex]] cards, only quads, plus a single [[DEC card form factor|extended length]] card. |
The BA11-E came with the [[H720 Power Supply]]; it was a separate unit, also mounted transversely in the box, at the back. It contained a [[transformer]], and a [[printed circuit board|PCB]] which supplied -15V (10A), and +5V (22A). | The BA11-E came with the [[H720 Power Supply]]; it was a separate unit, also mounted transversely in the box, at the back. It contained a [[transformer]], and a [[printed circuit board|PCB]] which supplied -15V (10A), and +5V (22A). | ||
| Line 15: | Line 17: | ||
The BA11-E's dimensions were 10-1/2" high, 19" wide, and 23" deep; it weighed roughly 100 lbs (including some backplanes and boards). | The BA11-E's dimensions were 10-1/2" high, 19" wide, and 23" deep; it weighed roughly 100 lbs (including some backplanes and boards). | ||
| − | [[Category: DEC | + | ==See also== |
| + | |||
| + | * [[BA11 mounting boxes]] | ||
| + | |||
| + | [[Category: DEC Mounting Boxes]] | ||
Latest revision as of 02:13, 11 July 2023
The BA11-E mounting box was one of the two earliest earliest standard system unit backplane mounting box produced by DEC, along with the BA11-C Mounting Box.
It was created for the expansion box role (hence the -E variant suffix) with the early PDP-11's (particularly the PDP-11/20). In that role, it was used to hold extra core main memory systems (each in their own custom system unit) and other devices, and had a blank front panel.
It came in two variants, the rack-mounted BA11-ES (including Tilt and Lock chassis slides), and the table-top BA11-EC. The rack-mounted ones were usually mounted in the H960 series of 19"-wide racks, which provided 63" of vertical mounting space, divided into units of 10-1/2". The 10-1/2" tall BA11-E mounting box was designed for these spaces
A BA11-E could hold up to six standard size (4-slot) system units; these were mounted transversely, facing down. They were generally mounted with the A-row connectors at the left-hand side.
A set of four cooling fans was also mounted at the left-hand side of the box, to provide air-flow to the boards and power supply. Since the fans intruded into the space 'above' (actually, to the side of, in the BA11-E - DEC location nomenclature assumes that the boards have their side edge at the top) the backplanes, the latter could not hold hex cards, only quads, plus a single extended length card.
The BA11-E came with the H720 Power Supply; it was a separate unit, also mounted transversely in the box, at the back. It contained a transformer, and a PCB which supplied -15V (10A), and +5V (22A).
Later versions of the H720 had a pair of connections to the standard DEC Remote Switching Control Bus, so it could turn other units off and on with its power switch.
The power harness ran along the left-hand side; it contained a number of single-width stub cards, which plugged into the power supply slot in the system units (generally the A connector in slot 3).
The BA11-E's dimensions were 10-1/2" high, 19" wide, and 23" deep; it weighed roughly 100 lbs (including some backplanes and boards).
