Difference between revisions of "DLV11-F asynchronous serial line interface"
(+img) |
m (→Further reading: +DLV11-F Replacement for the DLV11) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
The '''DLV11-F asynchronous serial line interface''' card (M8028) was a [[QBUS]] [[peripheral]] for the [[PDP-11]] series of computers which provided an [[asynchronous serial line]] on a single [[DEC card form factor|dual-width]] card. | The '''DLV11-F asynchronous serial line interface''' card (M8028) was a [[QBUS]] [[peripheral]] for the [[PDP-11]] series of computers which provided an [[asynchronous serial line]] on a single [[DEC card form factor|dual-width]] card. | ||
| − | It provided both [[EIA RS-232 serial line interface|EIA RS-232]] (with vestigial [[modem]] control), and active or passive [[20mA current loop serial line interface|20 mA]] connectivity. [[Baud rate]]s from 50 to 19,200 were available; receive and transmit can be set independently via configuration [[jumper]]s, or can be set via the [[register]]s, if desired (although not independently; either transmit only, or both). | + | It provided both [[EIA RS-232 serial line interface|EIA RS-232]] (with vestigial [[modem]] control), and [[20mA current loop serial line interface#'Active' and 'passive' modes|active or passive]] [[20mA current loop serial line interface|20 mA]] connectivity. [[Baud rate]]s from 50 to 19,200 were available; receive and transmit can be set independently via configuration [[jumper]]s, or can be set via the [[register]]s, if desired (although not input and output independently; either transmit only, or both). |
Line connection was via 40-pin [[Berg connector]] headers on the top edge of the card, using the standard [[DEC asynchronous serial line pinout]]. | Line connection was via 40-pin [[Berg connector]] headers on the top edge of the card, using the standard [[DEC asynchronous serial line pinout]]. | ||
| + | |||
| + | Configuration was via [[wire-wrap]] [[jumper]]s. | ||
==Programing interface== | ==Programing interface== | ||
| Line 17: | Line 19: | ||
==Layout== | ==Layout== | ||
| − | The 'Revison C' and later [[printed circuit board|PCB]] layouts are significantly different from the earlier ones; it is easy to recognize these versions visually, as the large [[asynchronous serial line#UART|UART]] chip is parallel to the long axis of the card. These versions are not covered in most DLV11-F documentation; they can be found in the ''"Microcomputer Interfaces Handbook"'' ( | + | The 'Revison C' and later [[printed circuit board|PCB]] layouts are significantly different from the earlier ones; it is easy to recognize these versions visually, as the large [[asynchronous serial line#UART|UART]] chip is parallel to the long axis of the card. These versions are not covered in most DLV11-F documentation; they can be found in the ''"Microcomputer Interfaces Handbook"'' (1980), on pg. 207. |
==See also== | ==See also== | ||
| Line 25: | Line 27: | ||
* [[DLV11-J asynchronous serial line interface]] | * [[DLV11-J asynchronous serial line interface]] | ||
| − | [[Category: QBUS Serial Interfaces]] | + | ==Further reading== |
| + | |||
| + | * ''DLV11-F Replacement for the DLV11'', [[MicroNote]] #046A | ||
| + | |||
| + | ==External links== | ||
| + | |||
| + | * [http://www.bitsavers.org/pdf/dec/qbus/EK-DLV11-OP-001_DLV11-E_and_DLV11-F_Asynchronous_Line_Interface_Users_Manual_Jun77.pdf DLV11-E and DLV11-F asynchronous line interface user's manual] (EK-DLV11-OP-001) | ||
| + | * [http://www.bitsavers.org/pdf/dec/qbus/Digital_Microcomputer_Interfaces_Handbook_1980.pdf Microcomputer Interfaces Handbook] - the DLV11-F, Revisions C and up, is covered on pp. 207 | ||
| + | * [https://manx-docs.org/collections/hcps/DLV11.pdf DLV11-F Field Maintenance Print Set] (MP00461) | ||
| + | |||
| + | [[Category: QBUS Asynchronous Serial Interfaces]] | ||
Latest revision as of 14:16, 25 July 2024
The DLV11-F asynchronous serial line interface card (M8028) was a QBUS peripheral for the PDP-11 series of computers which provided an asynchronous serial line on a single dual-width card.
It provided both EIA RS-232 (with vestigial modem control), and active or passive 20 mA connectivity. Baud rates from 50 to 19,200 were available; receive and transmit can be set independently via configuration jumpers, or can be set via the registers, if desired (although not input and output independently; either transmit only, or both).
Line connection was via 40-pin Berg connector headers on the top edge of the card, using the standard DEC asynchronous serial line pinout.
Configuration was via wire-wrap jumpers.
Programing interface
Like the ancestral KL11, the DLV11 has 2 device registers for the receive side (one Control and Status Register - CSR - and one data buffer register), and similarly, two for the transmit side. Each line has two interrupt vectors - again, one receive, and one transmit.
For the PDP-11 main console (which is always a KL11/DL11 compatible device), the standard is that 0777560 is the base address (so the receiver registers are 0777560-2, and the transmitter are 0777564-6), and 060 is the base vector. It can be set to halt the CPU when a 'break' is seen; it can also send a 'break'.
The first line after the console is always assigned the address 0776500, and vector 0300. Additional lines are assigned addresses and vectors immediately following, for DL11's #1-#16 (i.e. 0776500-676 and 0300-0476).
Layout
The 'Revison C' and later PCB layouts are significantly different from the earlier ones; it is easy to recognize these versions visually, as the large UART chip is parallel to the long axis of the card. These versions are not covered in most DLV11-F documentation; they can be found in the "Microcomputer Interfaces Handbook" (1980), on pg. 207.
See also
- DLV11 asynchronous serial line interface
- DLV11-E asynchronous serial line interface
- DLV11-J asynchronous serial line interface
Further reading
- DLV11-F Replacement for the DLV11, MicroNote #046A
External links
- DLV11-E and DLV11-F asynchronous line interface user's manual (EK-DLV11-OP-001)
- Microcomputer Interfaces Handbook - the DLV11-F, Revisions C and up, is covered on pp. 207
- DLV11-F Field Maintenance Print Set (MP00461)
