Difference between revisions of "KDF11-A CPU"

From Computer History Wiki
Jump to: navigation, search
m (rm dup cat)
m (→‎Further reading: +MMU Configuration Jumpers)
 
(11 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[Image:m8186.jpg|150px|thumb|right|M8186 CPU]]
+
[[Image:KDF11-ATop.jpg|250px|thumb|right|KDF11-A CPU, with KTF11-A MMU chip]]
  
−
The '''KDF11-A CPU''' is [[DEC card form factor|dual]]-width [[PDP-11]] CPU card for the [[QBUS]]; it uses the same 'Fonz' [[F-11 chip set]] as the other [[KDF11 CPUs]].
+
The '''KDF11-A CPU''' is a [[PDP-11]] [[Central Processing Unit|CPU]] for the [[QBUS]]; it is a [[DEC card form factor|dual]]-width [[printed circuit board|card]], the M8186. It uses the same 'Fonz' [[F-11 chip set]] as the other [[KDF11 CPUs]].
  
−
It contains only the basic CPU, unlike the other KDF-11's: no ROM, no serial lines, etc.
+
It contains only the basic CPU, unlike the other KDF-11's: no [[Read-only memory|ROM]], no [[asynchronous serial line]]s, etc. It does support the optional [[KTF11-A memory management chip]] and the [[KEF11-A floating point chip]], but not the [[KEF11-B]] [[PDP-11 Commercial Instruction Set]] (CIS); for higher performance [[floating point]], the [[FPF11 floating point processor]] may be used.
  
−
{{PDP-11}}
+
The first version of the KDF11-A (Revision A) only suppported 256 Kbytes of [[main memory]]; later versions supported up to 4 Mbytes (but their [[QBUS CPU ODT|ODT]]'s [[address space]] is limited to 256 Kbytes). In the later models, a bit in the [[PDP-11 Memory Management#Control|SSR3]] CPU [[register]] must be set to allow use of more than 256 Kbytes.
  
−
[[Category:QBUS processors]]
+
==Configuration==
 +
 
 +
A limited amount of configuration can be done with a number of [[jumper]]s in various locations (which differ depending on  [[etch]] revision, with block of eleven in the middle of the card.Their functions are:
 +
 
 +
{| border=1
 +
! Jumper !! Function !! In || Out
 +
|-
 +
|W1 || Master Clock || Enabled || Disabled
 +
|-
 +
|W2 || Reserved || Factory || Do not remove
 +
|-
 +
|W3 || Unknown
 +
|-
 +
|W4 || Event line || Disabled || Enabled
 +
|-
 +
|W5 || Powerup option bit 1
 +
|-
 +
|W6 || Powerup option bit 2
 +
|-
 +
|W7 || [[Halt]] enable || Halt || [[Trap]] to 4
 +
|-
 +
|W8 || [[Bootstrap]] [[address]] 0173000 || Yes || W9-W15
 +
|-
 +
|W09 || Bootstrap address bit 9 || 1 || 0
 +
|-
 +
|W10 || Bootstrap address bit 10 || 1 || 0
 +
|-
 +
|W11 || Bootstrap address bit 11 || 1 || 0
 +
|-
 +
|W12 || Bootstrap address bit 12 || 1 || 0
 +
|-
 +
|W13 || Bootstrap address bit 13 || 1 || 0
 +
|-
 +
|W14 || Bootstrap address bit 14 || 1 || 0
 +
|-
 +
|W15 || Bootstrap address bit 15 || 1 || 0
 +
|-
 +
|W16 || Reserved || Factory || Do not remove
 +
|-
 +
|W17 || Reserved || Factory || Do not remove
 +
|-
 +
|W18 || Wakeup circuit || Disabled || Enabled
 +
|}
 +
 
 +
Powerup options are:
 +
 
 +
{| border=1
 +
! W6 !! W5 !! Action
 +
|-
 +
| Out || Out || [[Program Counter|PC]] from 024, [[Processor Status Word|PS]] from 026
 +
|-
 +
| Out || In || ODT <!--, PS=0 -->
 +
|-
 +
| In || Out || PC=configuration jumpers <!--, PS=340 -->
 +
|-
 +
| In || In || Extended [[microcode]] (trap to 010 if none)
 +
|}
 +
 
 +
==Further reading==
 +
 +
* ''11/23 ECO Status'', [[MicroNote]] #104
 +
* ''MMU Configuration Jumpers'', MicroNote #102
 +
* ''Peripheral Compatibility with 11/23 Systems'', MicroNote #072
 +
 
 +
==External links==
 +
 
 +
* [http://www.bitsavers.org/pdf/dec/pdp11/1123/EK-KDF11-UG-PR2_Mar79.pdf KDF11-AA User's Guide] (EK-KDF11-UG-PR2)
 +
* [http://www.bitsavers.org/pdf/dec/pdp11/1123/MP00734_KDF11A_EngrDrws.pdf KDF11-A Field Maintenance Print Set] (MP00734)
 +
* [http://www.ibiblio.org/pub/academic/computer-science/history/pdp-11/hardware/micronotes/numerical/micronote17.txt LSI-11/23 ECO History] (uNote #017)
 +
 
 +
[[Category: PDP-11 QBUS Processors]]

Latest revision as of 22:46, 31 July 2024

KDF11-A CPU, with KTF11-A MMU chip

The KDF11-A CPU is a PDP-11 CPU for the QBUS; it is a dual-width card, the M8186. It uses the same 'Fonz' F-11 chip set as the other KDF11 CPUs.

It contains only the basic CPU, unlike the other KDF-11's: no ROM, no asynchronous serial lines, etc. It does support the optional KTF11-A memory management chip and the KEF11-A floating point chip, but not the KEF11-B PDP-11 Commercial Instruction Set (CIS); for higher performance floating point, the FPF11 floating point processor may be used.

The first version of the KDF11-A (Revision A) only suppported 256 Kbytes of main memory; later versions supported up to 4 Mbytes (but their ODT's address space is limited to 256 Kbytes). In the later models, a bit in the SSR3 CPU register must be set to allow use of more than 256 Kbytes.

Configuration

A limited amount of configuration can be done with a number of jumpers in various locations (which differ depending on etch revision, with block of eleven in the middle of the card.Their functions are:

Jumper Function In Out
W1 Master Clock Enabled Disabled
W2 Reserved Factory Do not remove
W3 Unknown
W4 Event line Disabled Enabled
W5 Powerup option bit 1
W6 Powerup option bit 2
W7 Halt enable Halt Trap to 4
W8 Bootstrap address 0173000 Yes W9-W15
W09 Bootstrap address bit 9 1 0
W10 Bootstrap address bit 10 1 0
W11 Bootstrap address bit 11 1 0
W12 Bootstrap address bit 12 1 0
W13 Bootstrap address bit 13 1 0
W14 Bootstrap address bit 14 1 0
W15 Bootstrap address bit 15 1 0
W16 Reserved Factory Do not remove
W17 Reserved Factory Do not remove
W18 Wakeup circuit Disabled Enabled

Powerup options are:

W6 W5 Action
Out Out PC from 024, PS from 026
Out In ODT
In Out PC=configuration jumpers
In In Extended microcode (trap to 010 if none)

Further reading

  • 11/23 ECO Status, MicroNote #104
  • MMU Configuration Jumpers, MicroNote #102
  • Peripheral Compatibility with 11/23 Systems, MicroNote #072

External links

Retrieved from "https://gunkies.org/w/index.php?title=KDF11-A_CPU&oldid=34994"