Difference between revisions of "PDP-10 memories"
(S-Bus details) |
m (interleaving cleanup) |
||
| (12 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | '''PDP-10 memories''' were generally all [[multi-port memory]] units. The [[PDP-10]] [[Central Processing Unit|CPU]] used one port (one per CPU in [[multi-processor]] systems); the others are used by [[channel]]s for [[mass storage]], such as [[disk]]s, to do [[Direct Memory Access|DMA]]. [[Memory interleaving|Interleaving]] was generally supported between units; usually in pairs, or sometimes groups of four. All except the very last ones were [[core memory|core]], and supported [[parity]] for [[error detection]]; the others were [[Metal Oxide Semiconductor|MOS]] [[Dynamic RAM|DRAM]], and used [[Error-correcting code|ECC]] to protect the memory contents. | |
| − | + | [[Image:KBusQCUnlatched.jpg|250px|thumb|left|KI-type memory bus Quick Latch connector (in unlatched position)]] | |
| − | The S-Bus ( | + | There were three generations of [[main memory]] [[bus]] (which ran sequentially through memory units to a [[terminator]]), and memory units for them. The first two were the so-called 'external memory bus', in KA (18-bit [[address]]) and KI (22-bit) forms (for the [[KA10]], and [[KI10]] and early [[KL10]], respectively), although they also had [[protocol]] differences. The last was the 'internal memory bus', the [[PDP-10 Memory Bus|S-Bus]]. (For the later KL10s, a later version of the S-Bus, the X-Bus, differed only in the [[logic family]] it interfaced to.) |
| + | |||
| + | The differences between the two external bus types required a [[KI10-M Memory Bus Adapter]] if KA-bit units were to be attached to a KI10. Similarly, KI-type units could be attached to the S-Bus using a [[DMA20 Memory Bus Adapter]]. | ||
| + | |||
| + | Most the memory units had a configuration panel which allowed ports to be enabled, and set the memory's address (often independently for each port); similarly, some level of interleaving could be set. | ||
| + | |||
| + | As was common with machines of that era, compatible PDP-10 main memory units were produced and sold by manufacturers other than [[Digital Equipment Corporation|DEC]]; some (but by no means all) are listed below. | ||
==Memory systems== | ==Memory systems== | ||
| − | 18-bit external: | + | 18-bit external (DEC): |
* [[MA10 core memory|MA10]] | * [[MA10 core memory|MA10]] | ||
| Line 13: | Line 19: | ||
* [[MD10 core memory|MD10]] | * [[MD10 core memory|MD10]] | ||
| − | 22-bit external: | + | 18-bit external (others): |
| + | |||
| + | * [[Fabritek Core Memory]] | ||
| + | |||
| + | 22-bit external (DEC): | ||
* [[ME10 core memory|ME10]] | * [[ME10 core memory|ME10]] | ||
| Line 20: | Line 30: | ||
* [[MH10 core memory|MH10]] | * [[MH10 core memory|MH10]] | ||
| − | Internal: | + | 22-bit external (others): |
| + | |||
| + | * [[Ampex ARM10|Ampex ARM-10L]] | ||
| + | |||
| + | Internal (DEC): | ||
* [[MA20 core memory|MA20]] | * [[MA20 core memory|MA20]] | ||
| Line 27: | Line 41: | ||
* [[MG20 MOS memory|MG20]] | * [[MG20 MOS memory|MG20]] | ||
| − | The first two groups are all | + | Internal (others): |
| + | |||
| + | * [[Ampex ARM20]] | ||
| + | |||
| + | The first two groups are all multi-port (generally 4 ports per memory system in the first group, and 8 in the second). The last group were for the later final KL10s (models KL10-E and KL10-R); all the DEC ones except the MF20 and MG20 were core. | ||
| + | |||
| + | ==See also== | ||
| + | |||
| + | * [[PDP-10 Memory Bus]] | ||
| − | [[Category: PDP-10 | + | [[Category: PDP-10 Memories]] |
Latest revision as of 02:27, 31 July 2023
PDP-10 memories were generally all multi-port memory units. The PDP-10 CPU used one port (one per CPU in multi-processor systems); the others are used by channels for mass storage, such as disks, to do DMA. Interleaving was generally supported between units; usually in pairs, or sometimes groups of four. All except the very last ones were core, and supported parity for error detection; the others were MOS DRAM, and used ECC to protect the memory contents.
There were three generations of main memory bus (which ran sequentially through memory units to a terminator), and memory units for them. The first two were the so-called 'external memory bus', in KA (18-bit address) and KI (22-bit) forms (for the KA10, and KI10 and early KL10, respectively), although they also had protocol differences. The last was the 'internal memory bus', the S-Bus. (For the later KL10s, a later version of the S-Bus, the X-Bus, differed only in the logic family it interfaced to.)
The differences between the two external bus types required a KI10-M Memory Bus Adapter if KA-bit units were to be attached to a KI10. Similarly, KI-type units could be attached to the S-Bus using a DMA20 Memory Bus Adapter.
Most the memory units had a configuration panel which allowed ports to be enabled, and set the memory's address (often independently for each port); similarly, some level of interleaving could be set.
As was common with machines of that era, compatible PDP-10 main memory units were produced and sold by manufacturers other than DEC; some (but by no means all) are listed below.
Memory systems
18-bit external (DEC):
18-bit external (others):
22-bit external (DEC):
22-bit external (others):
Internal (DEC):
Internal (others):
The first two groups are all multi-port (generally 4 ports per memory system in the first group, and 8 in the second). The last group were for the later final KL10s (models KL10-E and KL10-R); all the DEC ones except the MF20 and MG20 were core.
