Difference between revisions of "DF11 Communications Line Adapter"
From Computer History Wiki
m (+img) |
m (New cat) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
The '''DF11 Communications Line Adapter''' performs two functions for [[serial line]] communication [[interface]]s on [[PDP-11]] computers: i) converts from [[transistor-transistor logic|TTL]] signal levels to the [[voltage]]s, etc needed by a given serial line standard, and ii) produces the physical connector needed for that standard. | The '''DF11 Communications Line Adapter''' performs two functions for [[serial line]] communication [[interface]]s on [[PDP-11]] computers: i) converts from [[transistor-transistor logic|TTL]] signal levels to the [[voltage]]s, etc needed by a given serial line standard, and ii) produces the physical connector needed for that standard. | ||
| + | |||
| + | [[Image:M970.jpg|250px|thumb|right|M970 EIA Berg header card]] | ||
A DF11 usually involves two [[DEC card form factor|single-width]] cards, one holding the circuitry needed, and the other providing, sometimes with a cable plugged into a [[Berg connector]], the interface connector. At least one dual-width adapter (the DF11-B) existed, though. | A DF11 usually involves two [[DEC card form factor|single-width]] cards, one holding the circuitry needed, and the other providing, sometimes with a cable plugged into a [[Berg connector]], the interface connector. At least one dual-width adapter (the DF11-B) existed, though. | ||
| + | |||
| + | [[Image:M5960.jpg|250px|thumb|right|M5960 TTL to 20mA Level Converter]] | ||
The DF11 plugs into a common [[backplane]] with the serial interface. DF11's are used with [[DP11-A synchronous serial line interface|DP11]], [[DM11 asynchronous serial line interface|DM11]], [[DH11 asynchronous serial line interface|DH11]], [[DC11 asynchronous serial line interface|DC11]]; and [[DL11 asynchronous serial line interface|DL11]] and [[DU11 synchronous serial line interface|DU11]] [[UNIBUS]] serial interfaces (the latter two only in [[DD11-B backplane]]s, where the DF11 plugs into the A-B [[DEC edge connector contact identification|connectors]]). They may also be used in some versions of the [[PDP-11/05]] or [[PDP-11/10]]. | The DF11 plugs into a common [[backplane]] with the serial interface. DF11's are used with [[DP11-A synchronous serial line interface|DP11]], [[DM11 asynchronous serial line interface|DM11]], [[DH11 asynchronous serial line interface|DH11]], [[DC11 asynchronous serial line interface|DC11]]; and [[DL11 asynchronous serial line interface|DL11]] and [[DU11 synchronous serial line interface|DU11]] [[UNIBUS]] serial interfaces (the latter two only in [[DD11-B backplane]]s, where the DF11 plugs into the A-B [[DEC edge connector contact identification|connectors]]). They may also be used in some versions of the [[PDP-11/05]] or [[PDP-11/10]]. | ||
| + | |||
| + | [[Image:M973.jpg|250px|thumb|right|M973 20mA Mate-N-Lok header card]] | ||
DF11 models include: | DF11 models include: | ||
| Line 16: | Line 22: | ||
* DF11-K (M598, M973) - 4-wire opto-isolated 20mA adapter; '[[passive]]' mode (up to 2400 baud) | * DF11-K (M598, M973) - 4-wire opto-isolated 20mA adapter; '[[passive]]' mode (up to 2400 baud) | ||
| − | The DF11-K has [[jumper]]s to allow each channel to be changed to | + | The M5960 is a later, apparently improved [[20mA current loop serial line interface#'Active' and 'passive' modes|'active']] 20mA interface which replaces the M596. The M598 (DF11-K) has [[jumper]]s to allow each channel to be changed to 'active' mode. |
{{semi-stub}} | {{semi-stub}} | ||
| Line 24: | Line 30: | ||
* [http://www.bitsavers.org/pdf/dec/pdp10/periph/MP00068_DN87_Universal_Comm_System_Front_End_Jan76.pdf DN87 Field Maintenance Print Set] - contains complete engineering drawings for the DF11 boards on pp. 73-99 | * [http://www.bitsavers.org/pdf/dec/pdp10/periph/MP00068_DN87_Universal_Comm_System_Front_End_Jan76.pdf DN87 Field Maintenance Print Set] - contains complete engineering drawings for the DF11 boards on pp. 73-99 | ||
| − | [[Category: | + | [[Category: DEC Serial Interfaces]] |
Latest revision as of 20:23, 15 August 2022
The DF11 Communications Line Adapter performs two functions for serial line communication interfaces on PDP-11 computers: i) converts from TTL signal levels to the voltages, etc needed by a given serial line standard, and ii) produces the physical connector needed for that standard.
A DF11 usually involves two single-width cards, one holding the circuitry needed, and the other providing, sometimes with a cable plugged into a Berg connector, the interface connector. At least one dual-width adapter (the DF11-B) existed, though.
The DF11 plugs into a common backplane with the serial interface. DF11's are used with DP11, DM11, DH11, DC11; and DL11 and DU11 UNIBUS serial interfaces (the latter two only in DD11-B backplanes, where the DF11 plugs into the A-B connectors). They may also be used in some versions of the PDP-11/05 or PDP-11/10.
DF11 models include:
- DF11-A (M594, M957-BC01R, M970-BC01R for modem cable) - EIA RS-232 adapter
- DF11-BA (M586) - integral modem for connection to a telephone line
- DF11-BB (M587) - integral answer-only modem
- DF11-F (M596, M973) - 20m current loop adapter; 'active' mode (up to 300 baud)
- DF11-G (M595, BC01T-BC01Y) - custom 20mA interface to a Bell 301/303 modem
- DF11-K (M598, M973) - 4-wire opto-isolated 20mA adapter; 'passive' mode (up to 2400 baud)
The M5960 is a later, apparently improved 'active' 20mA interface which replaces the M596. The M598 (DF11-K) has jumpers to allow each channel to be changed to 'active' mode.
External links
- DN87 Field Maintenance Print Set - contains complete engineering drawings for the DF11 boards on pp. 73-99
