Difference between revisions of "Installing UNIX Sixth Edition"
(Add detail) |
(tweaks) |
||
| Line 1: | Line 1: | ||
There is a '''Setting up UNIX - Sixth Edition''' document, but it is mostly a checklist of what to do to install Unix on a [[PDP-11]] (one of the models supporting [[PDP-11 Memory Management|memory management]]); it does not provide any technical detail on what is actually happening. | There is a '''Setting up UNIX - Sixth Edition''' document, but it is mostly a checklist of what to do to install Unix on a [[PDP-11]] (one of the models supporting [[PDP-11 Memory Management|memory management]]); it does not provide any technical detail on what is actually happening. | ||
| − | UNIX Sixth Edition (often called UNIX V6) was normally installed from a tape; it was possible to install UNIX on a machine without a tape drive, by copying disk packs with UNIX on them, but this was not Bell Laboratories' usual | + | UNIX Sixth Edition (often called UNIX V6) was normally installed from a tape; it was possible to install UNIX on a machine without a tape drive, by copying disk packs with UNIX on them, but this was not Bell Laboratories' usual distribution method. Thus installing UNIX V6 usually required a machine with a tape drive, and one or more disk drives. |
The supported tape drives were the [[TU10]], on a [[TM11]] [[UNIBUS]] controller, and the [[TU16]], on a [[TM02]] [[MASSBUS]] controller. The supported disk drives were the [[RK05]], on an [[RK11]] UNIBUS controller, the [[RP03]] on an [[RP11]] UNIBUS controller, and the [[RP04]], with an internal controller which connected to a MASSBUS. | The supported tape drives were the [[TU10]], on a [[TM11]] [[UNIBUS]] controller, and the [[TU16]], on a [[TM02]] [[MASSBUS]] controller. The supported disk drives were the [[RK05]], on an [[RK11]] UNIBUS controller, the [[RP03]] on an [[RP11]] UNIBUS controller, and the [[RP04]], with an internal controller which connected to a MASSBUS. | ||
| Line 24: | Line 24: | ||
The copying programs (6 of them, one for each tape/disk combination) are stored in the block "2-xx" area. | The copying programs (6 of them, one for each tape/disk combination) are stored in the block "2-xx" area. | ||
| − | Blocks 100-4099 are an image an RK05 pack containing a UNIX root partition, which contains all the commands, and the source for the operating system; blocks 4100-8099 are an image of an RK05 pack which contains source for all the commands; and blocks 8100-12099 are an RK05 pack image which contains all the documentation. | + | Blocks 100-4099 are an image an RK05 pack containing a UNIX root partition, which contains everything needed to allow UNIX to run: all the commands, and the source for the operating system (to allow reconfiguration of the OS to match the system's hardware); blocks 4100-8099 are an image of an RK05 pack which contains source for all the commands; and blocks 8100-12099 are an RK05 pack image which contains all the documentation. |
==Programs== | ==Programs== | ||
Revision as of 14:35, 22 October 2016
There is a Setting up UNIX - Sixth Edition document, but it is mostly a checklist of what to do to install Unix on a PDP-11 (one of the models supporting memory management); it does not provide any technical detail on what is actually happening.
UNIX Sixth Edition (often called UNIX V6) was normally installed from a tape; it was possible to install UNIX on a machine without a tape drive, by copying disk packs with UNIX on them, but this was not Bell Laboratories' usual distribution method. Thus installing UNIX V6 usually required a machine with a tape drive, and one or more disk drives.
The supported tape drives were the TU10, on a TM11 UNIBUS controller, and the TU16, on a TM02 MASSBUS controller. The supported disk drives were the RK05, on an RK11 UNIBUS controller, the RP03 on an RP11 UNIBUS controller, and the RP04, with an internal controller which connected to a MASSBUS.
Installation process
The first stage is a tape bootstrap (loaded from block 0, or block 1, depending on the tape drive/controller on the system). That is then used to load an intermediate stage (named 'xxyy', where 'xx' is "tm" or "ht", and 'yy' is "rk", "rp" or "hp"), which is the program that copies the disk images to the actual drives.
That program is used to copy 3 disk pack images from the tape, to disk; it is also used to install an appropriate disk bootstrap in block 0 of the root drive.
Installation tape contents
The first 100 512-byte tape blocks contain a number of small programs, both tape and disk bootstraps, and programs to copy the tape contents to disk.
- Block 0 on tape - mboot (tm tape booter)
- Block 1 on tape - hboot (ht tape booter)
- Block 2-xx - a tp-format section containing the tape->disk copy programs
- Block 98 on tape - hpuboot
- Block 99 on tape - rpuboot
- Block 100 on tape - rkuboot
The copying programs (6 of them, one for each tape/disk combination) are stored in the block "2-xx" area.
Blocks 100-4099 are an image an RK05 pack containing a UNIX root partition, which contains everything needed to allow UNIX to run: all the commands, and the source for the operating system (to allow reconfiguration of the OS to match the system's hardware); blocks 4100-8099 are an image of an RK05 pack which contains source for all the commands; and blocks 8100-12099 are an RK05 pack image which contains all the documentation.
Programs
The first stage booter is "tpboot.s"; this is assembled with either "tm.s" or "ht.s" to produce the first-stage bootstrap that goes in blocks 0 and 1 of the tape. It takes a file-name, 'xxyy' as above, entered at the console.
"mcopy.s" is the tape copier program (assembled with either "tm.s" or "ht.s", and one of "rk.s", "rp.s" and "hp.s"), to produce the 'xxyy' files above.
"fsboot.s" is the disk bootstrap, assembled with "rk.s", "rp.s" or "hp.s" to produce the various disk bootstraps.
