Difference between revisions of "TU16 Tape Transport"
(A start) |
(cioyedit) |
||
| Line 7: | Line 7: | ||
}} | }} | ||
| − | The '''TU16''' is a classic big tape drive from [[Digital Equipment Corporation]], | + | The '''TU16''' is a classic big tape drive from [[Digital Equipment Corporation]], basically an updated version of the [[TU10]]. |
| − | The tape transport utilizes a single capstan, with vacuum columns. The TU16 drive contains a fair amount of electronics, in the form of several boards in a 4-slot [[DEC card form factor|hex]]-high backplane: | + | It is ble to store 5-40 Mbytes on a 2400' 0.5" wide tape, on a standard 10-1/2" reel. It supports 7-track operation at 200, 556, and 800 BPI, and 9-track operation 800 and 1600 BPI. The tape transport utilizes a single capstan, with vacuum columns. |
| + | |||
| + | The TU16 drive contains a fair amount of electronics, in the form of several boards in a 4-slot [[DEC card form factor|hex]]-high backplane: | ||
*M8910 - Logic and Write | *M8910 - Logic and Write | ||
| Line 16: | Line 18: | ||
*G056 - Read Amplifier | *G056 - Read Amplifier | ||
| − | In addition, that backplane contains three dual-high cards which interface to the drive bus: | + | The G056 and M8910 are hex cards; the others are dual. In addition, that backplane normally also contains three dual-high cards which interface to the drive bus: |
*M8913 - Data driver | *M8913 - Data driver | ||
Revision as of 03:08, 27 September 2016
| TU16 | |
| Tape speed: | 45 ips (Forward/Reverse) 150 ips (Rewind) |
|---|---|
| Size: | 19"W x 25"D x 26"H |
| Weight: | 150 lbs |
The TU16 is a classic big tape drive from Digital Equipment Corporation, basically an updated version of the TU10.
It is ble to store 5-40 Mbytes on a 2400' 0.5" wide tape, on a standard 10-1/2" reel. It supports 7-track operation at 200, 556, and 800 BPI, and 9-track operation 800 and 1600 BPI. The tape transport utilizes a single capstan, with vacuum columns.
The TU16 drive contains a fair amount of electronics, in the form of several boards in a 4-slot hex-high backplane:
- M8910 - Logic and Write
- M8911 - Slave Clock, Motion Delay
- M8912 - Slave Test Function Generator (two)
- G056 - Read Amplifier
The G056 and M8910 are hex cards; the others are dual. In addition, that backplane normally also contains three dual-high cards which interface to the drive bus:
- M8913 - Data driver
- M9001 - Bus Connector
- M9001-YA - Bus Connector
Controllers
To connect to UNIBUS PDP-11's, one of two controllers can be used.
The TU16 is normally used with a TM02 controller, which is a MASSBUS controller. The TU16/TM02 with an RH11 MASSBUS interface is denominated as a TJU16; with the RH70 MASSBUS interface of the PDP-11/70, it is denominated as a TWU16.
The TU16 can also be used with one of the TM11 series of magtape controllers. To connect to these controllers, in the first drive, the three dual-high bus interface cards (above) are replaced by an M8926 interface board. (Details of the controller-Master interface are given here.) Such a drive is a 'Master' TU10W drive; additional TU16 'Slave' drives (up to seven) may be connected to the Master drive.
