Difference between revisions of "Installing SITS on SIMH"
(Sample session.) |
(Replace VH with DH in configuration.) |
||
| Line 3: | Line 3: | ||
===Introduction=== | ===Introduction=== | ||
| + | SITS is cross-assembled from ITS, using the PALX assembler. These are the major components: | ||
| + | |||
| + | * SITS is the kernel. | ||
* RUG is a [[DDT]]-like memory resident [[debugger]], like [[Incompatible Timesharing System|ITS]]' non-[[time-sharing]] DDT. It can also handle a variety of media for reading and writing [[file]]s. | * RUG is a [[DDT]]-like memory resident [[debugger]], like [[Incompatible Timesharing System|ITS]]' non-[[time-sharing]] DDT. It can also handle a variety of media for reading and writing [[file]]s. | ||
* SALV is the disk salvager, same as in [[ITS]]. | * SALV is the disk salvager, same as in [[ITS]]. | ||
| Line 21: | Line 24: | ||
set ptp enabled | set ptp enabled | ||
set dci enabled address=17774000 vector=300 lines=1 | set dci enabled address=17774000 vector=300 lines=1 | ||
| − | set | + | set dh enabled address=17760020 vector=340 |
set rk enabled address=17777400 vector=220 | set rk enabled address=17777400 vector=220 | ||
set ng enabled address=17764040 vector=270 | set ng enabled address=17764040 vector=270 | ||
| Line 28: | Line 31: | ||
at -U dci 20001 | at -U dci 20001 | ||
| − | at -U | + | at -U dh 20002 |
at rk0 rk0.dsk | at rk0 rk0.dsk | ||
at rk1 rk1.dsk | at rk1 rk1.dsk | ||
Revision as of 07:27, 22 October 2022
Brief notes on installing SITS on SIMH.
Contents
Introduction
SITS is cross-assembled from ITS, using the PALX assembler. These are the major components:
- SITS is the kernel.
- RUG is a DDT-like memory resident debugger, like ITS' non-time-sharing DDT. It can also handle a variety of media for reading and writing files.
- SALV is the disk salvager, same as in ITS.
- SYSSPR is the system sphere, the first program run by SITS.
- DDT is the user interface command processor, like DDT/HACTRN in ITS.
- INQUIR handles a user database, like on ITS.
- FNT is a system program which loads fonts for use on the TV displays.
SIMH configuration
set cpu 11/45 set cpu 216k set ke enabled set pclk enabled set ptr enabled set ptp enabled set dci enabled address=17774000 vector=300 lines=1 set dh enabled address=17760020 vector=340 set rk enabled address=17777400 vector=220 set ng enabled address=17764040 vector=270 set tv enabled address=17764100 set mb enabled address=17770000 vector=374 at -U dci 20001 at -U dh 20002 at rk0 rk0.dsk at rk1 rk1.dsk at rk2 rk2.dsk at rk3 rk3.dsk
At the time of writing, the TV and MB devices have not yet been merged into mainline SIMH.
Prepare media
Have these absolute loader paper tapes ready:
- SALV
- RUG
Run RUG; PUNCH on ITS to read these PALX binaries and punch out paper tapes:
- SALV BIN
- SITS BIN
- SYSSPR BIN
- DDT BIN
- FNT BIN
PUNCH will divide the output in a series of tapes. It will valret in NEWBLK; continue with $P when a new tape has been mounted.
PUNCH will valret at EDONE when finished.
Format disks
Boot the SALV paper tape.
SALV will print a * prompt. For each of the four disk packs, type nI to format the pack. Only the first needs to be a "Rug disk".
SALV 174 *0Init sure?Y FFormat?N Rug disk?Y Reserved for syms file: 144-200 Swap area 1: 1000-2000 Swap area 2: Reserved: 0 Reserved: 4-23 Reserved: 54-143 Reserved: 201-217 Reserved: Writing block 000050 Writing block 000047 Disk name: SITS0 Writing block 000046 Writing block 000045 *
Install system files
Boot the RUG paper tape.
RUG will print a * prompt. First, type $^D to copy RUG to disk.
Load SALV, SITS, SYSSPR, DDT, and FNT from paper tape, and save them to disk. For each program type $L P: to load from tape. RUG will halt when it's time to mount the next tape, and return to the * prompt after the last tape. Type $Y to save the program to disk. The files are written to the "." directory on disk 0. Save SALV as the name DAZZEL. This is the default name for loading a file from RUG.
RUG can also load from a serial line with $L T: or over the Rubin 10-11 interface with $L M:, but this requires running ITS on the other end.
*$^D *$L P: HALT instruction, PC: 140522 (DECB R3) *$Y 0: DAZZEL HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 147604 (DECB R3) HALT instruction, PC: 147604 (DECB R3) HALT instruction, PC: 147604 (DECB R3) *$Y 0: SITS *$L P: HALT instruction, PC: 147604 (DECB R3) *$Y 0: SYSSPR *$L P: HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 140522 (DECB R3) HALT instruction, PC: 147604 (DECB R3) HALT instruction, PC: 147604 (DECB R3) *$Y 0: DDT *$L P: HALT instruction, PC: 140522 (DECB R3) *$Y 0: FNT *
Start SITS
Boot the RUG paper tape. (If RUG is already in memory, start it from 157000.) When started, RUG will print a * prompt.
Type $L 0: and enter. This will load SALV. Now type $G to start, getting SALV's * prompt.
Type G to check all disks. When done, SALV will go back to RUG through a special entry point which loads and starts SITS.
SITS starts the system sphere which prints SITS IS UP! You can now type ^Z on a teletype or DO IT on a TV keyboard to log in.
*$L 0: *$G SALV 174 *G Checking disk SITS0 Disk SITS0 refreshed 1713 blocks free out of 2436 Checking disk SITS1 Disk SITS1 refreshed 1919 blocks free out of 2436 Checking disk SITS2 Disk SITS2 refreshed 1919 blocks free out of 2436 Checking disk SITS3 Disk SITS3 refreshed 1919 blocks free out of 2436 SITS IS UP!
Logging in
Type ^Z to get the LOGIN: prompt. Type enter to bypass login and go to the SYSSPR # prompt. From there you can start DDT.
SYSSPR.238 SITS.119 LOGIN: #? ? CO CONTINUE D DDT GUN HELP KILL L LO LOAD LOGO LOGOUT GOODBYE ONLINE PEEK PERMIT RS RSTART SEND SYSKILL SYSSPR #DDT DDT.72 *:? PUNCH SYMADD NEWSPH LISTF DELETE PRINT YANK PDUMP LOAD BINLOAD SSTAT FONT CAPMODE MAPMODE SYSMODE CLEARSCREEN REVERSE ISPACE ? SETD LOGOUT DSPACE COPY ERROR LSI SITS *:LOGOUT BYE
