MSV11-R memory module

MSV11-R card

The MSV11-R (M7458) is a quad-height QBUS/PMI DRAM main memory card.

NOTE: As a PMI card, it uses the CD interconnect; it can therefore only be plugged into a Q/CD backplane. Plugging an MSV11-R card into a regular Q/Q backplane will damage the MSV11-R.

The MSV11-RA (M7358-A) holds 1 MByte when fully populated with 256K DRAM chips. The memory is arranged as 2 banks, each 16 data bits (1 PDP-11 word) wide, with 2 additional bits for parity (1 per byte). In theory, it could support being half-populated (512 Kbytes), with only one bank; there is a jumper, W1, which seems to support this configuration, but no documentation for it. It is not clear if DEC ever sold that configuration.

It is a Q22 card; it also supports block mode (with a maximum block size of 16. words, depending on the block's start address).

Configuration

A single 8-position DIP switch configures the card:

• Switches S1-S2 sets bits 21-20 of the board's 22-bit starting address;
• DEC documentation asserts that switches S3-S4 must always be off; however they seem to be functional (although perhaps only for the single bank configuration), and set address bits 19-18;
• Switches S5-S8 select the CSR address.

S1	S2	Staring Address
OFF	OFF	00000000 (0 MB)
OFF	ON	04000000 (1 MB)
ON	OFF	10000000 (2 MB)
ON	ON	14000000 (3 MB)

Control Register

Each board has a single control register, which can be configured in the range 17772100-17772136.

S5	S6	S7	S8	CSR Address
ON	ON	ON	ON	17772100
ON	ON	ON	OFF	17772102
ON	ON	OFF	ON	17772104
ON	ON	OFF	OFF	17772106
ON	OFF	ON	ON	17772110
ON	OFF	ON	OFF	17772112
ON	OFF	OFF	ON	17772114
ON	OFF	OFF	OFF	17772116
OFF	ON	ON	ON	17772120
OFF	ON	ON	OFF	17772122
OFF	ON	OFF	ON	17772124
OFF	ON	OFF	OFF	17772126
OFF	OFF	ON	ON	17772130
OFF	OFF	ON	OFF	17772132
OFF	OFF	OFF	ON	17772134
OFF	OFF	OFF	OFF	17772136

Technical information

A copy of the engineering drawings for the MSV11-R has recently been discovered, in a set of PDP-11/84 engineering drawings (see link below). As described above, each board has 2 banks in the array of DRAM chips; with 256K chips, each bank is thus 512KB. The chips in each bank run across the board (when it is oriented with the chip side facing the viewer, with the metal edging holding the handles at the top). Bit 0 (value 1) of the even byte of the low bank is on the right hand edge of the top row of the array; bit 15 (value 0100000), the top bit of the odd byte, is toward the left hand side of the second row. The two parity bits are on the extreme left hand edge. The high bank is in the third and fourth rows down the board from the metal handle edge. The full bit<->chip table is:

Bit	Bank 0	Bank 1
01	E76	E78
02	E83	E85
04	E90	E92
10	E94	E96
20	E101	E103
40	E108	E110
100	E114	E116
200	E121	E123
400	E75	E77
1000	E82	E84
2000	E89	E91
4000	E93	E95
10000	E100	E102
20000	E107	E109
40000	E113	E115
100000	E120	E122
Low byte Parity	E128	E130
High byte Parity	E127	E129

The following 256K DRAM chips have been observed to be used: MB81256-15 (Fujitsu).

Further reading

• MSV11-R User Guide, EK-MSV1R-UG

External links

• 11/84 Field Maintenance Print Set (MP-02015-001) - Contains MSV11-R engineering drawings on pp. 29-45