Installing 4.3 BSD on SIMH

This is the procedure that I have used to install 4.3 BSD onto SIMH's vax 11/780 emulator. Please note that this is the STOCK 4.3 BSD, not RENO, TAHOE or any other variant.

Requirements

You will need the following materials to put together a 4.3 BSD installation:

• A working perl interpeter to make the tape images.
  
• A copy of gzip.
  
• A method of extracting the boot file from either the binaries (tar/gzip) or uudecode to extract it from here.
  
• A compiled binary of vax780 from SIMH, along with the vmb.exe again from SIMH.

You will need the following files from any 4 BSD archive from the 4.2 directory. I have used the files from archive.huihoo.org. You can use whatever method you like to download them, wget, a web browser etc..

ingres.tar.gz
miniroot.gz
new.tar.gz
rootdump.gz
src.tar.gz
srcsys.tar.gz
stand.gz
usr.tar.gz
vfont.tar.gz

Preparing for installation

With the files downloaded you will need to uncompress them all and then create the tape file.

The following command will decompress the tape files.

gzip -d *.gz

The tape needs to be created with the mkdisttap.pl program. Simply run the program and redirect it into a file called 42.tap .

% ./mkdisttap.pl > 43.tap
% ls -l 43.tap
-rw-r--r--  1 Neozeed  None_ploc  111442472 Feb  6 15:18 43.tap

Next you will need the boot program. The boot program from 4.2 BSD works with 4.3 BSD. I have uploaded a copy onto this wiki in uuencoded format. To decode it, simply access the article, and copy the contents of the quoted text (the begin/end part INCLUDING the begin & end segments) and save it to a text file. Then you will need to run the uudecode file as follows:

% ls -l boot42.uue
-rw-r--r--  1 Neozeed  None_ploc  9117 Feb  6 12:09 boot42.uue
% uudecode boot42.uue
% ls -l boot42
-rw-------  1 Neozeed  None_ploc  6600 Feb  6 12:28 boot42
% file boot42
boot42: data

Boot 1.

We are going to use the following config file to start the first phase of the installation. Save the following configuration into a file such as 'install.ini'. Since we are going to boot directly into the miniroot the rq1 disk will hold the installation target. Since the 'normal' way to install is to install from tape onto the first disk, we will have to add a device file uppon boot for the second disk, and be sure to point the xtr program to the second disk.

install.ini

set rq0 ra81
at rq0 miniroot
set rq1 ra81
at rq1 rq.dsk
set rq1 dis
set rq2 dis
set rq3 dis
set rp dis
set lpt dis
set rl dis
set tq dis
set tu dis
att ts 43.tap
set tti 7b
set tto 7b
load -o boot42 0
d r10 9
d r11 0
run 2

Booting the emulator

You then simply run the emulator and pass it the config file.

C:\4.3BSD\work>vax780.exe install.ini

VAX780 simulator V3.8-0
RQ: creating new file
install.ini> set rq1 dis
Command not allowed
loading ra(0,0)boot
Boot
: ra(0,0)vmunix
279844+80872+100324 start 0x12f8
4.3 BSD UNIX #1: Fri Jun  6 19:55:29 PDT 1986
    karels@monet.Berkeley.EDU:/usr/src/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 140
avail mem = 7187456
using 140 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
ra1 at uda0 slave 1
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
Changing root device to ra0a
WARNING: clock lost 121 days -- CHECK AND RESET THE DATE!
erase ^?, kill ^U, intr ^C
#

Restoring the rootdump

From here we are now running from the miniroot. The next steps are as follows:

# cd /dev
# ./MAKEDEV ra1
# cd /
# disk=ra1 type=ra81 tape=ts xtr

This will create a 'device' for the ra1 disk, then run the xtr program to restore the root dump. Take note that the chgrp & chmod commands are not found, however the install will proceed as normal.

erase ^?, kill ^U, intr ^C
# cd /dev
# ./MAKEDEV ra1
./MAKEDEV: chgrp: not found
./MAKEDEV: chmod: not found
# cd /
# disk=ra1 type=ra81 tape=ts xtr
Build root file system
Warning: 538 sector(s) in last cylinder unallocated
/dev/rra1a:     15884 sectors in 23 cylinders of 14 tracks, 51 sectors
        8.1Mb in 2 cyl groups (16 c/g, 5.85Mb/g, 1856 i/g)
super-block backups (for fsck -b#) at:
 32, 11520,
Check the file system
** /dev/rra1a
** Last Mounted on
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2 files, 9 used, 7420 free (20 frags, 925 blocks, 0.3% fragmentation)
Rewind tape
Restore the dump image of the root
Warning: ./lost+found: File exists
** /dev/rra1a
** Last Mounted on /a
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
317 files, 4199 used, 3230 free (6 frags, 403 blocks, 0.1% fragmentation)
Root filesystem extracted

If this is an 8650 or 8600, update the console rl02
If this is a 780 or 785, update the floppy
If this is a 730, update the cassette
#

After this stage, I just sync the disk a few times, then halt the emulator (CONTROL+E) and exit out. Now we are ready for stage two.

If this is a 730, update the cassette
# sync
# sync
# sync

Simulation stopped, PC: 800018AE (BRB 800018A3)
sim> q
Goodbye

C:\4.3BSD\work>

Boot 2.

Now that the install disk is prepared, we need to use a different config file to reflect us going back to a single disk/tape configuration. The new configuration is as follows:

boot.ini

set rq0 ra81
att rq0 rq.dsk
set rq1 dis
set rq2 dis
set rq3 dis
set rp dis
set lpt dis
set rl dis
set tq dis
set tu dis
att ts 43.tap
set tti 7b
set tto 7b
load -o boot42 0
d r10 9
d r11 0
run 2

Booting the emulator

Now boot up the emulator with the boot.ini

C:\4.3BSD\work>vax780.exe boot.ini

VAX780 simulator V3.8-0
loading ra(0,0)boot
Boot
: ra(0,0)vmunix
279844+80872+100324 start 0x12f8
4.3 BSD UNIX #1: Fri Jun  6 19:55:29 PDT 1986
    karels@monet.Berkeley.EDU:/usr/src/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 140
avail mem = 7187456
using 140 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
Changing root device to ra0a
Automatic reboot in progress...
Thu Feb  6 07:35:07 PST 1986
Can't open checklist file: /etc/fstab
Automatic reboot failed... help!
erase ^?, kill ^U, intr ^C
#

Preparing the disk

Now we have to prep the machine for both the tape, and the type of disk. Type in the following commands.

# disk=ra
# name=ra0h;type=ra81
# cd /dev
# sh ./MAKEDEV ts0;sync
# cd /
# newfs $name $type

The output will be like this:

# disk=ra
# name=ra0h;type=ra81
# cd /dev
# sh ./MAKEDEV ts0;sync
# cd /
# newfs $name $type
Warning: 680 sector(s) in last cylinder unallocated
/dev/rra0h:     291346 sectors in 409 cylinders of 14 tracks, 51 sectors
        149.2Mb in 26 cyl groups (16 c/g, 5.85Mb/g, 2048 i/g)
super-block backups (for fsck -b#) at:
 32, 11520, 23008, 34496, 45984, 57472, 68960, 80448, 91936, 103424,
 114912, 126400, 137888, 149376, 160864, 172352, 182816, 194304, 205792, 217280,
 228768, 240256, 251744, 263232, 274720, 286208,
#

Restoring the usr slice

The disk's /usr slice will not have been formatted. We can not go ahead and mount it, and restore the /usr files. Then we unmount the slice, and run fsck to make sure everything is ok.

# mount /dev/$name /usr
# cd /usr
# mkdir sys
# cd sys
# mt rew
# mt fsf 3
# tar xpbf 20 /dev/rmt12
# cd ..
# mt fsf
# tar xpbf 20 /dev/rmt12
# cd /
# chmod 755 / /usr /usr/sys
# rm -rf sys
# ln -s /usr/sys sys
# umount /dev/$name
# fsck /dev/r$name

Likewise, the output should be similar to this:

# mount /dev/$name /usr
# cd /usr
# mkdir sys
# cd sys
# mt rew
# mt fsf 3
# tar xpbf 20 /dev/rmt12
# cd ..
# mt fsf
# tar xpbf 20 /dev/rmt12
# cd /
# chmod 755 / /usr /usr/sys
# rm -rf sys
# ln -s /usr/sys sys
# umount /dev/$name
# fsck /dev/r$name
** /dev/rra0h
** Last Mounted on /usr
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
4645 files, 35630 used, 102954 free (162 frags, 12849 blocks, 0.1% fragmentation)
#

Configuring the fstab

Now we just need to create the fstab, format the 'home' slice, and then we can reboot the emulator into multiuser mode. Enter in the following commands:

# cd /etc
# cp fstab.ra81 fstab
# newfs ra0g ra81
# sync
# reboot

And the expected output is as follows:

# cp fstab.ra81 fstab
# newfs ra0g ra81
/dev/rra0g:     515508 sectors in 722 cylinders of 14 tracks, 51 sectors
        263.9Mb in 46 cyl groups (16 c/g, 5.85Mb/g, 2048 i/g)
super-block backups (for fsck -b#) at:
 32, 11520, 23008, 34496, 45984, 57472, 68960, 80448, 91936, 103424,
 114912, 126400, 137888, 149376, 160864, 172352, 182816, 194304, 205792, 217280,

 228768, 240256, 251744, 263232, 274720, 286208, 297696, 309184, 320672, 332160,

 343648, 355136, 365600, 377088, 388576, 400064, 411552, 423040, 434528, 446016,

 457504, 468992, 480480, 491968, 503456, 514944,
# sync
# reboot
syncing disks... done

Reboot requested, PC: 8002B03A (MOVL 8004F628,R0)
sim> q
Goodbye

First Multiuser Boot

Now we can just re-run the last command, and we should boot multiuser! By default there is no root password. Also the system will run fsck uppon boot, so depending on your host computer this could take a while.

C:\4.3BSD\work>vax780.exe boot.ini

VAX780 simulator V3.8-0
loading ra(0,0)boot
Boot
: ra(0,0)vmunix
279844+80872+100324 start 0x12f8
4.3 BSD UNIX #1: Fri Jun  6 19:55:29 PDT 1986
    karels@monet.Berkeley.EDU:/usr/src/sys/GENERIC
real mem  = 8388608
SYSPTSIZE limits number of buffers to 140
avail mem = 7187456
using 140 buffers containing 524288 bytes of memory
mcr0 at tr1
mcr1 at tr2
uba0 at tr3
hk0 at uba0 csr 177440 vec 210, ipl 15
rk0 at hk0 slave 0
rk1 at hk0 slave 1
rk2 at hk0 slave 2
rk3 at hk0 slave 3
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
zs0 at uba0 csr 172520 vec 224, ipl 15
ts0 at zs0 slave 0
dz0 at uba0 csr 160100 vec 300, ipl 15
dz1 at uba0 csr 160110 vec 310, ipl 15
dz2 at uba0 csr 160120 vec 320, ipl 15
dz3 at uba0 csr 160130 vec 330, ipl 15
Changing root device to ra0a
Automatic reboot in progress...
Thu Feb  6 07:43:43 PST 1986
/dev/ra0a: 330 files, 4200 used, 3229 free (5 frags, 403 blocks, 0.1% fragmentat
ion)
/dev/rra0h: 4645 files, 35630 used, 102954 free (162 frags, 12849 blocks, 0.1% f
ragmentation)
/dev/rra0g: 2 files, 9 used, 245216 free (16 frags, 30650 blocks, 0.0% fragmenta
tion)
Thu Feb  6 07:43:50 PST 1986
checking quotas: done.
starting system logger
checking for core dump... /a/crash: No such file or directory

Feb  6 07:43:51 myname savecore: /a/crash: No such file or directory
starting local daemons:Feb  6 07:43:51 myname named[53]: /etc/named.boot: No suc
h file or directory
 named sendmail.
preserving editor files
clearing /tmp
standard daemons: update cron accounting.
starting network daemons: rwhod inetd printer.
Thu Feb  6 07:43:52 PST 1986
Feb  6 07:43:54 myname getty: /dev/tty03: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty02: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty05: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty04: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty07: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty06: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty00: No such file or directory
Feb  6 07:43:54 myname getty: /dev/tty01: No such file or directory


4.3 BSD UNIX (myname.my.domain) (console)

login:

Now we can simply logon as root.

4.2 BSD UNIX (myname)

login: root
4.2 BSD UNIX #9: Wed Nov 2 16:00:29 PST 1983

Would you like to play a game?

You have mail.
Don't login as root, use su
myname#

From here you can explore the system. All of the man pages are installed, and there is enough of a base system to get going. Sadly there are bugs in how 4.2 BSD and how SIMH interact with the networking, and it is not reliable. As sad as it is to be an 'island' you can however setup the dz serial interface to allow more than one user.

Enabling remote users

You can add the following lines into the boot.ini (just make sure they are above the boot command or it'll not work correctly..

set dz lines=8
att dz 8888
set dz 7b

I would also recommend to windows users, either putty, or syncterm. The default telnet client sucks.