DP11-A Synchronous Line Interface

The DP11-A is the earliest synchronous serial line interface for the UNIBUS; it was double-buffered, and used programmed I/O (with separate receive and transmit interrupts) to transfer data, in either half-duplex or full-duplex, at baud rates up to 50K bits/second.

It was intended to interface to Bell 201, 301 and 303 series modems. The character length (6, 7 or 8 bits), and the sync character, were selectable under program control, as were idling (sending the sync character), as well as the modem control leads; the DP11-A could also be set to discard incoming sync characters.

Options allowed extending the character length to 10, 11 or 12 bits, and use of an internal clock.

It was constructed from a number of smaller FLIP CHIPs, along with a larger board, which were installed in a custom 4-slot backplane system unit. It used one of the DF11 Communications Line Adapter‎s to interface to the modem.

Registers

Register	Abbreviation	Address
Receiver Control and Status Register	DPRCSR	774770
Receiver Buffer Register	DPRBUF	774772
Sync Register	DPSYNC	774773
Additional Sync Register	DPASYNC	774777
Transmitter Control and Status Register	DPXCSR	774774
Transmitter Buffer Register	DPXBUF	774776

The two SYNC registers seem to overlay the buffer registers; this is not yet sorted out.

The addresses shown are for the first DP11-A in a system; additional ones are normally set to be at 774760, 774750, etc to 774400.

774770: Receiver Control and Status Register (DPRCSR)

Unused			CPAR	RACT	BPCH			RDN	RDIE	Unused		MRCV	MAINT	HLFD	STRS
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• CPAR - Character Parity; parity of last character in the receive buffer
• RACT - Receiver Active; set after two consecutive sync characters
• BPCH - Bits per Character, selects between 6-8, 10-12 bits per character
• RDN - Receive Done Flag; set when the receive buffer contains an assembled character
• RDIE - Receive Interrupt Enable; allows an input interrupt when Receive Done Flag is set
• MRCV - Miscellaneous Receive; monitor any non-standard modem status
• MAINT -Maintenance Mode; connect Transmitter output to Receiver input, CTS simulation
• HLFD - Half Duplex; RTS on inhibits Receive logic
• STRS - Strip Sync; sync characters following Receive Active are discarded

774774: Transmitter Control and Status Register (DPXCSR)

CARRF	RXOF	RING	MRDY	CARR	CTS	RTS	Unused	XDN	XDIE	XSIE	Unused	MXMT	Unused	IDLS	TRDY
15	14	13	12	11	10	09	08	07	06	05	04	03	02	01	00

• CARRF - Carrier Flag; set when modem's Carrier lead goes from On to Off
• RXOF - Receiver Overrun Flag; receiver buffer not read before end of next character
• RING - Ring Flag; indicates a Ring signal from the modem
• MRDY - Modem Ready; current state of modem Data Set Ready lead
• CARR - Carrier; current state of modem Carrier lead
• CTS - Clear to Send; current state of mode CTS lead
• RTS - Request to Send; set when transmit buffer is loaded, or if Idle Sync is set
• XDN - Transmit Done Flag; set when output character transmission has started
• XDIE - Transmit Done Interrupt Enable; allows a transmit interrupt when Transmit Done Flag is set
• XSIE - Transmit Status Interrupt Enable; allows a transmit interrupt when any flag bit is set
• MXMT - Miscellaneous Transmit; control any non-standard modem status
• IDLS - Idle Sync; allows transmission from the sync buffer
• TRDY - Terminal Ready; controls connection of data communication gear to communication channel

Implementation

The modules are:

• G8000 - +8V Filter
• M105 - UNIBUS Address Selector Module
• M239 - Divide by 16 Module (optional)
• M405 - Clock Module (optional)
• M594 - EIA Level Converter Module
• M7820 - Interrupt Control
• M7065 - Receiver Module (one mandatory, two optional)
• M7075 - Transmitter Module (ditto)
• M7223 - Control Module

The M7223 is a quad card; the others are all single. (Of those, the M105, M7820, M7065 and M7075 are extended length; the M239 and M405 are standard length.)

The M594 can be substituted with other adapter cards from the DF11 series; in particular, the M595 is used with the Bell 303 series modem.

Board locations (as seen from the board insertion side of the backplane, not the wire-wrap pin side, as is common in DEC documentation) are:

	Connector
Slot	A	B	C	D	E	F
1	UNIBUS In		M7223
2	G8000 Filter		M105	M7820	M405	M239
3	Power		M7075	M7065	M7075	M7065
4	UNIBUS Out		Modem connector	Level Converter

Power comes in on a single-width stub card in the A3 slot (as is canonical in the PDP-11/20 generation of PDP-11s).