DM11 Asynchronous 16-line Single-Speed Multiplexer
The DM11 Asynchronous 16-Line, Single-Speed Multiplexer (formally, the DM11-AA) was a very early UNIBUS peripheral which provided up to 16 asynchronous serial line connections. It was in some sense a predecessor to the DH11, in that it used DMA.
However, unlike any other UNIBUS peripheral, much of its internal state was actually stored in main memory, not in registers in the device itself (not even in ones not directly accessible from the UNIBUS); DMA was used to gain access to it. (Perhaps this was early enough in time that gates for flip-flops for registers were too expensive, or took too much space on the board.)
The data stored in memory included:
- per-line current output buffer address
- per-line current output transfer length
- per-line input shift registers
- input buffer (a shared, circular FIFO buffer)
The line parameters:
- baud rates (ranging from 45 to 1200)
- character length (5-8 bits)
- output stop bits (1 or 2)
The implementation of the basic DM11-AA used a custom double system unit backplane, containing multiple cards; a flat cable connected this to separate rack-mounted dual-height DM11 distribution panel backplane (which required its own independent power supply).
Modular 'line conditioning' units from the DF11 Communications Line Adapter series were installed in the distribution panel to allow support of either 20mA or EIA RS-232 serial lines. The alternative DC08CS distribution panel allowed connection to telegraph and Telex lines.
Lines could be connected to modems, provided the correct line conditioning units were installed, but modem control required a DM11-BB Modem Control Option, mounted in the main DM11 backplane along with the rest of the DM11-AA cards, and connected to the distribution panel via other flat cables which carried the modem control signals. The DM11-BB is logically a separate device from the DM11-AA, albeit one housed in the same DM11 backplane.
DM11-AA Device registers
|Buffer Active Register||DMBAR||775002|
|Break Status Register||DMBSR||775004|
|Base Address Register||DMBADR||775006|
The Buffer Active Register has one bit per line to indicate that has output pending (described by the Current Address and Word Count tables below); the Break Status Register also has one bit per line. The Base Address Register is 8 bits wide, so the in-memory tables must start on a 0400 boundary.
The addresses shown are for the first DM11-AA11 in a system; additional ones (up to 16 total) are normally set to be at 775010, 775020, etc to 775170.
775000: Status Register (DMCSR)
- TINT - Transmit Interrupt
- TO - Timeout; non-existent memory referenced
- SOVR - System Overrun; bus access not gained in time
- TIE - Transmit Interrupt Enable
- DONE - Done; input character placed in the Circular Buffer
- RIE - Receiver Interrupt Enable
- MEMEX - Memory Extension
- MAINT - Maintenance Bit; connects line 0 (only) receiver directly to transmitter
- FHD - Full/Half Duplex Select; disables receivers on lines that are transmitting
- RENB - Receiver Enable
The four tables of per-line data kept in main memory were:
|Table||Offset (in bytes)||Size (in bytes)|
The first two are for transmitting, and defined the output buffer; the last two for receiving. The format of the entries in the input buffer is:
The input character, which may be less than 8 bits wide, is stored right-justified.
The DM11-AA boards (all quad, except for the Control C, which is a dual) which plugged into the DM11 backplane are:
- M7240 - Control A
- M7241 - Control B
- M7242 - Control C
- M7243 - Transmitter D
- M7244 - Transmitter E
- M7245 - Receiver
and 4 single-width, non-DM11-specific cards:
|3||Power||Reserved for DM11-BB|
|4||UNIBUS Out||Reserved for DM11-BB|
(NOTE: The diagram which is the source for this table has two different cards marked as 'M7245', and no 'M7243's. So it clearly has errors; the M7243 is referred to elsewhere as the transmitter card, and the M7245 as the receiver, so the numbers are correct, but the locations might be swapped.)
- DM11 asynchronous 16-line single-speed multiplexer manual (DEC-11-HDMA-D, EK-DM11A-TM-002) - latter is available in fiche, but neither is online
- DM11 Asynchronous 16-Line Single-Speed Multiplexer Engineering Drawing Manual - not available online
- DM11-BB Modem Control Option Engineering Drawings - not available online
- DM11-BB modem control option manual, (DEC-11-HDMBA-A-D) pp. 1-5
- pdp11 peripherals and interfacing handbook (1972 edition) - the DM11 is covered on pp. 141-160 of the PDF