MM11-L core memory

From Computer History Wiki
(Redirected from ME11-L)
Jump to: navigation, search
G110 control logic board; the blank area in the center right holds the extra components for the parity bits in the G109 variant

The MM11-L core memory was a popular, and common, 16 Kbyte core main memory unit for the early PDP-11 UNIBUS machines. An MM11-L was composed of a three board set:

  • G110 - hex-width memory control logic and data channels
  • G231 - hex-width memory driver logic
  • H214 - quad-width core stack

The MM11-L required a custom backplane, although some CPU's (e.g. the PDP-11/05) had processor backplanes wired to hold one or more MM11-L sets, in addition to the CPU.

The MM11-S was a four-slot backplane plus a single MM11-L board set. The MF11-L was a nine-slot backplane plus a single MM11-L board set; the backplane has room for two more MM11-L board sets. The ME11-L was an MF11-L in a 5-1/4" rack-mount box, with power supply (the -LA was wired for 115V supply, the -LB for 230V).

The G231 board of the MM11-L is also used, with the 19-bit wide H216 variant of the core stack, in the MF10 core memory.

Parity

H215 parity core memory board

There was also a parity variant of the MM11-L, the MM11-LP; parity versions (denoted by a 'P' suffix) were available for all of the above. The MM11-LP added a dual-width M7259 Parity Control Module, and substituted an H215 (with two more bits per word - for byte parity) for the H214, and a G109 for the G110. (The G109 and G110 use the same etch; the G110 omits the components for the two parity bits.) Enabling parity increased the access time from 400 nsec to 525 nsec.

The manual indicates that an 'MF11-LP backplane' was required, but it is not stated if this version had a different PCB, or if the non-parity version simply had a jumper, like the MM11-U core memory. After some investigation, apparently there were two versions of the backplane, the early one (DEC part number 54-09959) which cannot run parity, and a later one (part number 54-10331) which can. An example of the later backplane had the same jumper as that called for for the MM11-U, from pin 1BU1 to 2BU1; this jumper should not be present for parity memory.

The parity controller, if present, can only be placed in slot 6. The backplane connects together all the BU1 SSYN pins on the interior slots (2-8), effectively an 'internal' SSYN; the jumper connects together that line, and the main UNIBUS SSYN. The G109/G110 modules drive that 'internal' SSYN; hence the need to install the jumper for non-parity memory. When parity is enabled, the parity controller drives the bus SSYN via pin BV2 in its slot, which is directly connected to bus SSYN via a trace; the controller uses the 'internal' SSYN as input.

Note that therefore parity and non-parity memory cannot be mixed on the same backplane. There is also no provision for use of the M7259 parity controller in the PDP-11/05 backplanes which support the MM11-L.

(One could probably easily ECO the earlier version backplane to support parity, since the SSYN trace is accessible: cut the trace at 1BU1 and 9BU1, and add the needed wire-wrap lines.)

Module chart

The board organization in the MM11-L backplanes is not given in the manual; that for the MF11-L is:

Connector
Slot A B C D E F
1 UNIBUS In H213/H214 Core stack
2 G231 Memory Driver
3 G110 Memory Control
4 G231 Memory Driver
5 G110 Memory Control
6 M7259 Parity Controller H213/H214 Core stack
7 G231 Memory Driver
8 G110 Memory Control
9 UNIBUS Out H213/H214 Core stack

The first MM11-L set goes in slots 1/2/3; as MM11-L sets were added, they were installed in slot numerical order. (The location of the parity controller is the only un-used dual slot in a full MF11-L.)

See also

External links