Difference between revisions of "RS03/04 disk drive"
(An OK start) |
(Addnl info) |
||
| Line 6: | Line 6: | ||
| capacity = 512KB (RS03), 1024KB (RS04) | | capacity = 512KB (RS03), 1024KB (RS04) | ||
| surfaces = 1 (RS03), 2 (RS04) | | surfaces = 1 (RS03), 2 (RS04) | ||
| − | | tracks = 64 | + | | tracks = 64 (plus 8 spares) |
| sectors = 64 | | sectors = 64 | ||
| words per sector = 128 bytes (RS03), 256 bytes (RS04) | | words per sector = 128 bytes (RS03), 256 bytes (RS04) | ||
| Line 13: | Line 13: | ||
| density = xxx bpi (maximum) | | density = xxx bpi (maximum) | ||
| recording method = [[Modified Frequency Modulation|MFM]] | | recording method = [[Modified Frequency Modulation|MFM]] | ||
| − | | physical size = 15-3/4" (high), 19" (width) | + | | physical size = 15-3/4" (high), 19" (width), 26-1/4" (depth) |
| − | | weight = | + | | weight = 120 lbs |
| − | | power consumption = 13A (starting), | + | | power consumption = 13A (starting), 6A (operating) |
| controller = [[RH11 MASSBUS controller|RH11]] ([[UNIBUS]]), [[RH70 MASSBUS controller|RH70]], [[RH10 MASSBUS controller|RH10]] | | controller = [[RH11 MASSBUS controller|RH11]] ([[UNIBUS]]), [[RH70 MASSBUS controller|RH70]], [[RH10 MASSBUS controller|RH10]] | ||
<!-- | <!-- | ||
| Line 27: | Line 27: | ||
|}} | |}} | ||
| − | The '''RS03''' and '''RS04 disk drives''' were [[MASSBUS]] fixed-platter [[fixed-head disk]] [[drive]]s. Their basic format was 18-[[bit]] [[word]]s (for use in [[PDP-10]] and [[PDP-15]] machines), but they | + | The '''RS03''' and '''RS04 disk drives''' were [[MASSBUS]] fixed-platter [[fixed-head disk]] [[drive]]s. Their basic format was 18-[[bit]] [[word]]s (for use in [[PDP-10]] and [[PDP-15]] machines), but they could be used in [[PDP-11]]s, where they simply ignored two bits. |
| + | |||
| + | They attach to any MASSBUS controller, e.g. [[RH11 MASSBUS controller|RH11]] ([[UNIBUS]]), [[RH70 MASSBUS controller|RH70]], or [[RH10 MASSBUS controller|RH10]]. Up to 8 devices total can be attached to any MASSBUS controller. | ||
The RS04 doubled the capacity (and bit rate) of the RS03 by recording on both sides of the [[platter]]; alternate bits in each word came from alternate sides. | The RS04 doubled the capacity (and bit rate) of the RS03 by recording on both sides of the [[platter]]; alternate bits in each word came from alternate sides. | ||
| − | They could store up to 512KB of data in 128 byte blocks (RS03), or 1024KB of data in 256 byte blocks (RS04). They used | + | They could store up to 512KB of data in 128 byte blocks (RS03), or 1024KB of data in 256 byte blocks (RS04). They used 64 fixed read/write [[head]]s per side for data (8 spares were provided), and 2 heads to read timing/address [[track]]s (a main and a backup). |
| + | |||
| + | The second timing track did not provide reliability/redundancy; the two tracks were not recorded synchonously. Switch-over from one to another was manual, by inverting a connector. | ||
| − | + | The drive had the ability to write-protect tracks 0-N ('N' set in switches). | |
{{semi-stub}} | {{semi-stub}} | ||
[[Category: DEC Disk Drives]] | [[Category: DEC Disk Drives]] | ||
Revision as of 03:15, 22 November 2018
| RS03/RS04 | |
| Manufacturer: | Digital Equipment Corporation |
|---|---|
| Drive Controller(s): | RH11 (UNIBUS), RH70, RH10 |
| Capacity: | 512KB (RS03), 1024KB (RS04) |
| Transfer Rate: | 2 μsec/byte (RS03), μ1 sec/byte (RS04) |
| Average Access Time: | 8.5 msec (60Hz), 10.2 msec (50Hz) |
| Revolutions per Minute: | 3600 (60Hz) |
| Media: | 16" diameter nickel-cobalt plated surface |
| Total Surfaces: | 1 (RS03), 2 (RS04) |
| Tracks per Surface: | 64 (plus 8 spares) |
| Sectors per Track: | 64 |
| Words per Sector: | 128 bytes (RS03), 256 bytes (RS04) |
| Density: | xxx bpi (maximum) |
| Recording Method: | MFM |
| Physical Size: | 15-3/4" (high), 19" (width), 26-1/4" (depth) |
| Weight: | 120 lbs |
| Power Consumption: | 13A (starting), 6A (operating) |
The RS03 and RS04 disk drives were MASSBUS fixed-platter fixed-head disk drives. Their basic format was 18-bit words (for use in PDP-10 and PDP-15 machines), but they could be used in PDP-11s, where they simply ignored two bits.
They attach to any MASSBUS controller, e.g. RH11 (UNIBUS), RH70, or RH10. Up to 8 devices total can be attached to any MASSBUS controller.
The RS04 doubled the capacity (and bit rate) of the RS03 by recording on both sides of the platter; alternate bits in each word came from alternate sides.
They could store up to 512KB of data in 128 byte blocks (RS03), or 1024KB of data in 256 byte blocks (RS04). They used 64 fixed read/write heads per side for data (8 spares were provided), and 2 heads to read timing/address tracks (a main and a backup).
The second timing track did not provide reliability/redundancy; the two tracks were not recorded synchonously. Switch-over from one to another was manual, by inverting a connector.
The drive had the ability to write-protect tracks 0-N ('N' set in switches).
