Difference between revisions of "RL01/02 disk drive"

From Computer History Wiki
Jump to: navigation, search
(Add a bunch of data)
(+year introduced)
 
(31 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
{{Infobox Disk drive
 
{{Infobox Disk drive
−
| name = RL01
+
| name = RL01 / RL02
−
| manufacturer = [[Digital Equipment Corporation]]  
+
| manufacturer = [[Digital Equipment Corporation]]
−
| controller = [[RL11 disk controller|RL11]] ([[UNIBUS]])
+
| year introduced = November, 1979 (RL02)
−
| capacity = 5.2 Mbytes (formatted)
+
| controller = [[RL11 disk controller|RL11]] ([[UNIBUS]])<br>[[RLV11 disk controller|RLV11]] and [[RLV12 disk controller|RLV12]] ([[QBUS]])<br>[[RL8-A disk controller|RL8-A]] ([[OMNIBUS]])
 +
| capacity = 5.2 Mbytes (formatted) (RL01)<br>10.4 Mbytes (formatted) (RL02)
 
| transfer rate = 512 Kbytes/sec<br>3.9 usec/word (peak)
 
| transfer rate = 512 Kbytes/sec<br>3.9 usec/word (peak)
 
| average access time = 67.5 msec
 
| average access time = 67.5 msec
Line 11: Line 12:
 
| average seek = 55 msec
 
| average seek = 55 msec
 
| maximum seek = 100 msec
 
| maximum seek = 100 msec
 +
| head switch = 8 msec (maximum)
 
| surfaces = 2
 
| surfaces = 2
−
| tracks = 256
+
| tracks = 256 (RL01)<br>512 (RL02)
 
| sectors = 40
 
| sectors = 40
 
| words per sector = 128
 
| words per sector = 128
−
| tracks per inch = 125
+
| tracks per inch = 125 (RL01)<br>250 (RL02)
 
| density = 3725 bpi (maximum)
 
| density = 3725 bpi (maximum)
−
| recording method = [[Modified Frequence Modulation]] (MFM)
+
| recording method = [[Modified Frequency Modulation]] (MFM)
 +
| start time = 40 seconds
 +
| stop time = 30 seconds
 
| physical size = 19" W x 10-1/2" H x 25" L
 
| physical size = 19" W x 10-1/2" H x 25" L
 
| weight = 55 pounds
 
| weight = 55 pounds
Line 23: Line 27:
 
}}
 
}}
  
−
[[Image:rl01.jpg|150px|thumb|left|An RL01]]
+
[[Image:Rl02.jpg|150px|thumb|left|An RL02 cartridge]]
  
−
The RL01 is a 5MiB, single platter, removable [[pack]] [[disk|disk drive]] introduced in 1976 by [[Digital Equipment Corporation]]. It used an [[IBM 5440]] type pack, as used on the [[IBM System/3]].
+
The '''RL01''' and '''RL02''' are single platter, removable pack [[disk|disk drives]], introduced in 1976 and 1978 respectively, by [[Digital Equipment Corporation|DEC]]. They used an [[IBM 5440]] type pack, as used on the [[IBM System/3]]. Up to 4 drives may be attached to a single [[device controller|controller]]; the drives are connected serially. The total length of the string may not exceed 100 feet.
  
−
To keep the [[head]]s properly aligned on the [[track]]s, it used a servo system driven by servo data written on the pack (along with [[sector]] headers) at the factory; packs ''cannnot'' be low-level re-formatted in the field.
+
The RL01 is a 5MiB drive, and the RL02 is 10MiB; the latter is a high-density version, with twice as many [[track]]s per surface, but otherwise mostly identical.
  
−
[[Image:rl01drive.jpg|150px|thumb|left|RL01 drive]]
+
To keep the [[head]]s properly aligned on the tracks, it used a servo system driven by servo data written on the pack (along with [[sector]] headers) at the factory. Packs ''cannnot'' be low-level re-formatted in the field, and are not compatible with both drive types (although both types are physically identical).
  
−
The [[QBUS]] controllers are the [[RLV11]] and [[RLV12]], the latter being the [[QBUS|Q22]] version.
+
[[Image:rl02drive.jpg|150px|thumb|left|An RL02 drive; note the label]]
  
−
The [[RL02 disk drive|RL02]] is a higher density version, with twice as many [[track]]s.
+
Early versions of the drives included a set of brushes that swing out over the [[platter]] on start-up; these were deleted in later versions.
  
−
[[Category: DEC Disk Drives]]
+
The [[UNIBUS]] controller is the [[RL11 disk controller|RL11]], a single [[DEC card form factor|hex]] card. The [[QBUS]] controllers are the [[RLV11 disk controller|RLV11]] and [[RLV12 disk controller|RLV12]]; the former consists of two [[DEC card form factor|quad]] cards, and needs a QBUS [[backplane]] with [[CD interconnect]]; the latter is a single quad card, and is also the [[QBUS#Variable address size|Q22]] version. The [[OMNIBUS]] controller (for the [[PDP-8 family|PDP-8]]) is the [[RL8-A disk controller|RL8-A]]. Furthermore there is a special controller, the [[RB730 Integrated Disk Controller]], for RL02 and [[R80]] drives connected to the [[VAX-11/730]] only.
 +
 
 +
==Cabling==
 +
 
 +
[[Image:rl01drive.jpg|thumb|right|An RL01 drive; note no label]]
 +
 
 +
The RL0x uses a cable with latching connectors at each end to go between drives; the part number of the original cable is 70-12122-xx (where xx is the length, one of -08, 10, 20, 40 or 60); it is also known as a BC20J-xx. A later version, with thicker cable, is the BC21Z-xx (see in -06, 08, 10, and 25). A still later version with metallic coating on the connector, and thicker double shielded cable is the BC17F-xx (only observed in -10).
 +
 
 +
To get from the controller to the first drive of the string, one of two setups can be used.
 +
 
 +
A BC80M-xx cable has a [[Berg connector]] at one end which plugs into the controller, and one of the latching connectors to connect to a drive at the other. Alternatively, a BC06R-xx [[flat cable]] goes from the controller to a transition adapter (part number 70-12415-0-0) in a mounting bracket attached to the rack; a standard cable goes from there to the first drive. (If the flat cable is plugged into the adapter the wrong way around, no damage is done; the 'Fault' lights on the drives on that string come on, is all.)
 +
 
 +
[[Image:rl01.jpg|150px|thumb|right|An RL01 pack]]
 +
 
 +
The drive string must be ended with a [[terminator]] on the 'out' port of the last drive, part number 70-12293-0-0 (although the terminators generally have no markings on them). Again, terminators in both plain black plastic, and with silvery metallic coating, have been observed.
 +
 
 +
The terminators and transition adapters for the RL01/02 and [[RK06/07 disk drive]]s are the same, and interchangeable. The cables are semi-compatible; RK06/7 cables may be used with the RL01/02, but not the other way around - those for the RK06/07 have additional wires which are not present in the RL01/02 cables.
 +
 
 +
==Moving==
 +
 
 +
[[Image:RL0xHeadLatch.jpg|200px|thumb|left|Head latch (moving position)]]
 +
 
 +
As is common on older moving-head removable pack drives, the heads are (or ''should be'') mechanically held from moving with a manually-installed restraint when the drive is transported. On the RL01/02, this is a small rectangular plate, held down with a machine screw, which prevents the head from moving out into the pack compartment. To install/remove the restraint, simply loosen the screw (do '''''not''''' remove it, or the plate), and rotate the plate 90 degrees.
 +
 
 +
The RL01/02 also uses a pair of screws, on the bottom of the drive, to secure the (heavy) drive motor when the drive is being shipped; install these before moving a drive, and make sure to remove them when installing one.
 +
 
 +
==Installation==
 +
 
 +
The RL01/02 drives use fairly custom slides (shared with the [[RA81 disk drive|RA81]], among others); they bolt onto the side of the drive (using the thin rail riveted to the drive on the sides to help support the weight), and they are handed (i.e. different on the left and right side).
 +
 
 +
There seem to be two generations of slides; the part #'s for the newer ones are: 1213686-00 Rev-K1-R and 1213686-00 Rev-K1-L. Older drives have been observed with slides which don't have any visible part #'s; they look almost identical to the later ones, except that the newer ones have two rocking trip levers (one in the middle, and one at one end), and the older ones have only one (the one in the middle).
 +
 
 +
==Opening the drive without power==
 +
 
 +
On RL01/02 drives, the top hinged cover (which must be lifted to insert/remove packs) is held shut with a latch which itself has a solenoid release latch; unless the drive is powered up, the solenoid latch is not released, and the top cannot be opened. (This is a safety feature, to prevent the hinged cover being opened when the pack is still spinning.)
 +
 
 +
Some later drives have access panels which can be removed to gain to the solenoid. On older ones, one has to loosen the four screws holding down the rear cover on the top of the drive, and lift the front edge where it traps the pins of the hinged cover; this allows the back of the hinged cover to be raised slightly, and therby clear the solenoid latch, allowing the main latch to be operated.
 +
 
 +
==4.3 BSD disktab==
 +
 
 +
<pre>
 +
rb02|RB02|DEC RL02 on 730 IDC:\
 +
    :ty=removable:se#256:ns#40:nt#2:nc#32:\
 +
    :pa#15884:ba#4096:fa#1024:\
 +
    :pb#4480:pc#20480:</pre>
 +
 
 +
==Emulating the RL02==
 +
 
 +
Reinhard Heuberger has created an open source emulator for the RL02 (and RL01) using a Terasic DE0-Nano Altera Cyclone IV FPGA board, extended with necessary interfacing hardware and an SD card slot. The emulator can be used with a real PDP-11, for example.
 +
* [http://www.pdp11gy.com/doneE.html Home page of project]
 +
* [http://www.vintage-computer.com/vcforum/album.php?albumid=184&attachmentid=12300 Picture of the simulator connected to a PDP-11/53]
 +
 
 +
==External links==
 +
 
 +
* [http://www.bitsavers.org/pdf/dec/disc/rl01_rl02/ RL01/RL02] - documentation at [[Bitsavers]]
 +
** [http://www.bitsavers.org/pdf/dec/disc/rl01_rl02/EK-RL012-UG-005_Sep81.tif.pdf RL01/RL02 Disk Drive User Guide] (EK-RL012-UG-005)
 +
** [http://www.bitsavers.org/pdf/dec/disc/rl01_rl02/RL02techDescr.pdf RL0l/RL02 Disk Drive Technical Manual] (EK-RL012-TM-PRE)
 +
** [http://www.bitsavers.org/pdf/dec/disc/rl01_rl02/EK-RL122-TM-001_techAug82.pdf RL01/RL02 Technical Manual - Volume II - Service Procedures] (EK-RL122-TM-00l)
 +
* [https://www.pdp-11.nl/peripherals/disk/rl-info.html RL01 / RL02 removable hard disk drive] - Henk Gooijen's extensive RL01/RL02 material; provides a great deal of useful information about using these drives
 +
 
 +
[[Category: DEC Early Disk Drives]]
 +
[[Category: DEC Removable-pack Disks]]

Latest revision as of 15:33, 18 August 2023


RL01 / RL02
Manufacturer: Digital Equipment Corporation
Year Introduced: November, 1979 (RL02)
Drive Controller(s): RL11 (UNIBUS)
RLV11 and RLV12 (QBUS)
RL8-A (OMNIBUS)
Capacity: 5.2 Mbytes (formatted) (RL01)
10.4 Mbytes (formatted) (RL02)
Transfer Rate: 512 Kbytes/sec
3.9 usec/word (peak)
Average Access Time: 67.5 msec
Revolutions per Minute: 2400
1/2 Revolution Time: 12.5 msec
One Track Seek Time: 15 msec
Average Seek Time: 55 msec
Maximum Seek Time: 100 msec
Head Switching Time: 8 msec (maximum)
Total Surfaces: 2
Tracks per Surface: 256 (RL01)
512 (RL02)
Sectors per Track: 40
Words per Sector: 128
Tracks per Inch: 125 (RL01)
250 (RL02)
Density: 3725 bpi (maximum)
Recording Method: Modified Frequency Modulation (MFM)
Start Time: 40 seconds
Stop Time: 30 seconds
Physical Size: 19" W x 10-1/2" H x 25" L
Weight: 55 pounds
Power Consumption: 160W (running); 550 VA (starting)


An RL02 cartridge

The RL01 and RL02 are single platter, removable pack disk drives, introduced in 1976 and 1978 respectively, by DEC. They used an IBM 5440 type pack, as used on the IBM System/3. Up to 4 drives may be attached to a single controller; the drives are connected serially. The total length of the string may not exceed 100 feet.

The RL01 is a 5MiB drive, and the RL02 is 10MiB; the latter is a high-density version, with twice as many tracks per surface, but otherwise mostly identical.

To keep the heads properly aligned on the tracks, it used a servo system driven by servo data written on the pack (along with sector headers) at the factory. Packs cannnot be low-level re-formatted in the field, and are not compatible with both drive types (although both types are physically identical).

An RL02 drive; note the label

Early versions of the drives included a set of brushes that swing out over the platter on start-up; these were deleted in later versions.

The UNIBUS controller is the RL11, a single hex card. The QBUS controllers are the RLV11 and RLV12; the former consists of two quad cards, and needs a QBUS backplane with CD interconnect; the latter is a single quad card, and is also the Q22 version. The OMNIBUS controller (for the PDP-8) is the RL8-A. Furthermore there is a special controller, the RB730 Integrated Disk Controller, for RL02 and R80 drives connected to the VAX-11/730 only.

Cabling

An RL01 drive; note no label

The RL0x uses a cable with latching connectors at each end to go between drives; the part number of the original cable is 70-12122-xx (where xx is the length, one of -08, 10, 20, 40 or 60); it is also known as a BC20J-xx. A later version, with thicker cable, is the BC21Z-xx (see in -06, 08, 10, and 25). A still later version with metallic coating on the connector, and thicker double shielded cable is the BC17F-xx (only observed in -10).

To get from the controller to the first drive of the string, one of two setups can be used.

A BC80M-xx cable has a Berg connector at one end which plugs into the controller, and one of the latching connectors to connect to a drive at the other. Alternatively, a BC06R-xx flat cable goes from the controller to a transition adapter (part number 70-12415-0-0) in a mounting bracket attached to the rack; a standard cable goes from there to the first drive. (If the flat cable is plugged into the adapter the wrong way around, no damage is done; the 'Fault' lights on the drives on that string come on, is all.)

An RL01 pack

The drive string must be ended with a terminator on the 'out' port of the last drive, part number 70-12293-0-0 (although the terminators generally have no markings on them). Again, terminators in both plain black plastic, and with silvery metallic coating, have been observed.

The terminators and transition adapters for the RL01/02 and RK06/07 disk drives are the same, and interchangeable. The cables are semi-compatible; RK06/7 cables may be used with the RL01/02, but not the other way around - those for the RK06/07 have additional wires which are not present in the RL01/02 cables.

Moving

Head latch (moving position)

As is common on older moving-head removable pack drives, the heads are (or should be) mechanically held from moving with a manually-installed restraint when the drive is transported. On the RL01/02, this is a small rectangular plate, held down with a machine screw, which prevents the head from moving out into the pack compartment. To install/remove the restraint, simply loosen the screw (do not remove it, or the plate), and rotate the plate 90 degrees.

The RL01/02 also uses a pair of screws, on the bottom of the drive, to secure the (heavy) drive motor when the drive is being shipped; install these before moving a drive, and make sure to remove them when installing one.

Installation

The RL01/02 drives use fairly custom slides (shared with the RA81, among others); they bolt onto the side of the drive (using the thin rail riveted to the drive on the sides to help support the weight), and they are handed (i.e. different on the left and right side).

There seem to be two generations of slides; the part #'s for the newer ones are: 1213686-00 Rev-K1-R and 1213686-00 Rev-K1-L. Older drives have been observed with slides which don't have any visible part #'s; they look almost identical to the later ones, except that the newer ones have two rocking trip levers (one in the middle, and one at one end), and the older ones have only one (the one in the middle).

Opening the drive without power

On RL01/02 drives, the top hinged cover (which must be lifted to insert/remove packs) is held shut with a latch which itself has a solenoid release latch; unless the drive is powered up, the solenoid latch is not released, and the top cannot be opened. (This is a safety feature, to prevent the hinged cover being opened when the pack is still spinning.)

Some later drives have access panels which can be removed to gain to the solenoid. On older ones, one has to loosen the four screws holding down the rear cover on the top of the drive, and lift the front edge where it traps the pins of the hinged cover; this allows the back of the hinged cover to be raised slightly, and therby clear the solenoid latch, allowing the main latch to be operated.

4.3 BSD disktab

rb02|RB02|DEC RL02 on 730 IDC:\
    :ty=removable:se#256:ns#40:nt#2:nc#32:\
    :pa#15884:ba#4096:fa#1024:\
    :pb#4480:pc#20480:

Emulating the RL02

Reinhard Heuberger has created an open source emulator for the RL02 (and RL01) using a Terasic DE0-Nano Altera Cyclone IV FPGA board, extended with necessary interfacing hardware and an SD card slot. The emulator can be used with a real PDP-11, for example. 

* Home page of project
* Picture of the simulator connected to a PDP-11/53

External links

Retrieved from "https://gunkies.org/w/index.php?title=RL01/02_disk_drive&oldid=31207"