Difference between revisions of "Installing Ultrix V1.1 on SIMH"
From Computer History Wiki
(First Draft) |
m (Added Category:SIMH Tutorials) |
||
| Line 841: | Line 841: | ||
Goodbye | Goodbye | ||
Log file closed | Log file closed | ||
| + | |||
| + | [[Category:SIMH Tutorials]] | ||
Revision as of 11:33, 24 June 2022
Contents
Introduction
The aim of this tutorial is to show how to install Ultrix V1.1 on the supported SIMH MicroVAX / VAX simulators.
>>> All user input is formatted in bold <<<
The installation includes:
- Ultrix V1.1 Mini System
- Ultrix V1.1 Full System
- All Ultrix V1.1 Software Subsets
- Local Area Network Configuration
Preparations
Suitable SIMH MicroVAX / VAX Simulators
You can choose between the following MicroVAX / VAX Models resp. SIMH simulators that are supported by Ultrix V1.1:
| MicroVAX / VAX Model | SIMH simulator |
|---|---|
| MicroVAX I | microvax1 |
| MicroVAX II | microvax2 |
| VAX-11/780 | vax780 |
| VAX-11/750 | vax750 |
| VAX-11/730 | vax730 |
In this tutorial I use the vax780 SIMH simulator.
The VAX-11/780 system used here consists of:
- KA780 CPU
- MS780 8 MB Memory
- DZ11 8 Line Terminal Multiplexor
- UDA50 Disk Controller
- RA81 Disk
- RH780 Massbus Controller
- TU77 Massbus Tape Drive
- DEUNA Ethernet Controller
Ultrix V1.1
Get the Ultrix V1.1 installation kit here, unzip and put the files contained into the directory where the SIMH simulator resides.
vax780.ini
Use the following vax780.ini file for a VAX-11/780 system:
; Sample VAX780.ini for ULTRIX V1.1
SET QUIET
SET CPU 8M
; DISABLE ALL UNUSED DEVICES
SET RP DIS
SET RY DIS
SET RL DIS
SET TQ DIS
SET TS DIS
SET HK DIS
SET CR DIS
; ACTIVATE CONSOLE LOGGING
SET CONSOLE LOG=001.LOG
; ENABLE TU77 TAPE DRIVE
SET TU ENA
SET TU0 TU77
ATT TU0 ultrix-32_1.1_sys_sw_1of2.tap
;ATT TU0 BB-EA81B-BE_DECnet-Ultrix_1.1_86.tap
SET TU1 DIS
SET TU2 DIS
SET TU3 DIS
SET TU4 DIS
SET TU5 DIS
SET TU6 DIS
SET TU7 DIS
; ENABLE RA81 SYSTEM DISK DRIVE
SET RQ0 RA81
ATT RQ0 ULT011.R81
SET RQ1 DIS
SET RQ2 DIS
SET RQ3 DIS
; ENABLE DZ11 ASYNC ADAPTER
SET DZ 7B
SET DZ LINES=8
ATT DZ 6666
; ENABLE LINE PRINTER
SET LPT ENA
ATT LPT PRINTEROUTPUT.TXT
; SET CONSOLE TO 7 BIT
SET TTI 7B
SET TTO 7B
; ENABLE DEUNA ETHERNET ADAPTER
SET XU ENABLE
SET XU TYPE=DEUNA
;ATT XU ETH0
ATT CS ult011_console.rx1
; ====================================================================
; R10 = Boot Disk Type
; R10 is irrelevant in case of Conversational Boot ("Ask")
; ====================================================================
; DEP R10 9 = RA0
; DEP R10 109 ; = RA1
; DEP R10 209 ; = RA2
; DEP R10 11 ; = RB (11/730)
; DEP R10 3 ; = HK
; DEP R10 2 ; = UP (???)
; DEP R10 14 ; = RL
; ====================================================================
; R11 = Boot Type
; ====================================================================
; DEP R11 0 ; = Multiuser
; DEP R11 1 ; = Multiuser Conversational (e.g. "ra(0,0)vmunix")
; DEP R11 2 ; = Single User
; DEP R11 3 ; = Single User Conversational
; DEP R11 60000010; = DIAG SUPER
; ====================================================================
; LOAD & START UTILITY FROM CONSOLE FLOPPY
; ====================================================================
; FLOAD BOOT 0 ; = Boot
; FLOAD COPY 0 ; = Copy
; RUN 2 ; = Start loaded Utility
Installation
Copy Ultrix V1.1 Mini System from Tape to Disk
sim> DEP R10 9 sim> DEP R11 3 sim> FLOAD COPY 0 sim> RUN 2 From: ht(0,1) To: ra(0,1) Copy completed: 300 records copied From: [STRG + e] Simulation stopped, PC: 00004BCA (RET) sim>
Boot Ultrix V1.1 Mini System and create Full System on Disk
sim> DEP R10 9
sim> DEP R11 3
sim> FLOAD BOOT 0
sim> RUN 2
Boot
: ra(0,1)vmunix
220688+77372+63260 start 0x1420
Ultrix V1.1 System #1: Thu May 9 08:45:41 EDT 1985
real mem = 8384512
avail mem = 6916096
using 153 buffers containing 838656 bytes of memory
VAX 11/780, serial no. 1234, hardware level = 7
mcr0 (MS780-C) at address 0x20002000, 4096Kbytes, noninterleaved
mcr1 (MS780-C) at address 0x20004000, 4096Kbytes, noninterleaved
uba0 at address 0x20006000
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
de0 at uba0 csr 174510 vec 120, ipl 15
lp0 at uba0 csr 177514 vec 200, ipl 14
mba0 at address 0x20010000
ht0 at mba0 drive 0
tu0 at ht0 slave 0
root device? ra0*
WARNING: clock gained 44 days -- CHECK AND RESET THE DATE!
erase ^?, kill ^U, intr ^C
List of recognized distribution media devices:
te16 ts11 ts05 tu45 tu77 tu78 tu80
ra60 rc25 rl02 rk07
What type of drive is the distribution media
mounted on [no default]: tu77
List of recognized disk drives to contain root filesystem:
ra60 ra80 ra81 rk07 rm03 rm05 rm80 rp05 rp06
rp07 rc25
What type of drive is going to contain the root filesystem [no default]: ra81
Unit 0 is the only supported unit number
for this device. These installation procedures
will use this unit number unless you specify an
alternate.
Do you wish to specify an alternate unit
number (y/n) [default: n]? n
- - - Build root file system on ra0 - - -
Warning: 538 sector(s) in last cylinder unallocated
/dev/rra0a: 15884 sectors in 23 cylinders of 14 tracks, 51 sectors
8.1Mb in 2 cyl groups (16 c/g, 5.85Mb/g, 1856 i/g)
super-block backups (for fsck -b#) at:
32, 11520,
- - - Check the file system - - -
** /dev/rra0a
** Last Mounted on
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2 files, 9 used, 7420 free (20 frags, 925 blocks)
- - -Rewinding tape - - -
- - - Restoring the dump image of the root - - -
** /dev/rra0a
** Last Mounted on /destination
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
704 files, 3872 used, 3557 free (21 frags, 442 blocks)
-*-*-* Root filesystem is now extracted onto -*-*-*
-*-*-* the destination disk filesystem -*-*-*
- - - Building the console floppy - - -
Please remove the distribution floppy from the
drive and store it in a safe place. Insert the
VAX-11/780/785 console floppy diskette.
Press RETURN when you have done this or type
'skip' to skip this step): skip
Skipping console update
You must now reboot the new root filesystem.
When you are told the system is ready to be
halted, perform the following steps:
1) Type the following:
^P (get the attention of the
console subsystem)
H (halt the processor)
U (unjam the SBI
I (initialize the processor)
2) B ANY
3) Respond to 'Boot:' with--
ra(0,0)vmunix
4) Respond to 'Root device?' with--
ra0
syncing disks... done
THE PROCESSOR CAN NOW BE HALTED.
Infinite loop, PC: 80023BC4 (BRB 80023BC4)
sim>
Boot Ultrix V1.1 Full System, Configure and Compile Kernel
sim> DEP R11 3
sim> FLOAD BOOT 0
sim> RUN 2
Resetting all devices... This may not have been your intention.
The GO and CONTINUE commands do not reset devices.
Boot
: ra(0,0)vmunix
220688+77372+63260 start 0x1420
Ultrix V1.1 System #1: Thu May 9 08:45:41 EDT 1985
real mem = 8384512
avail mem = 6916096
using 153 buffers containing 838656 bytes of memory
VAX 11/780, serial no. 1234, hardware level = 7
mcr0 (MS780-C) at address 0x20002000, 4096Kbytes, noninterleaved
mcr1 (MS780-C) at address 0x20004000, 4096Kbytes, noninterleaved
uba0 at address 0x20006000
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
de0 at uba0 csr 174510 vec 120, ipl 15
lp0 at uba0 csr 177514 vec 200, ipl 14
mba0 at address 0x20010000
ht0 at mba0 drive 0
tu0 at ht0 slave 0
root device? ra0
erase ^?, kill ^U, intr ^C
*** Setting the System Date ***
Please specify the date (yymmddhhmm): 8506132126
Thu Jun 13 21:26:00 EDT 1985
*** Changing the Super User password ***
New password: ult011 (not echoed)
Retype new password: ult011 (not echoed)
*** Building the Special File for the Installation Tapedrive ***
special files for ht0 are *mt{0,4,8,12}
*** Making and Extracting the /usr filesystem ***
Creating the /usr filesystem in ra0g.
Save the super-block numbers generated here. Tape
them to the outside of the disk pack cover. If
your pack is nonremovable, tape them to the
outside of the drive. They can be very useful in
certain emergencies.
- - - - - - - - - - - - - - - - - - - - - - -
*** SUPER BLOCK NUMBERS FOR /USR IN FS ra0g ***
Warning: 30 sector(s) in last cylinder unallocated
/dev/rra0g: 82080 sectors in 115 cylinders of 14 tracks, 51 sectors
42.0Mb in 8 cyl groups (16 c/g, 5.85Mb/g, 2048 i/g)
super-block backups (for fsck -b#) at:
32, 11512, 22992, 34472, 45952, 57432, 68912, 80392,
- - - - - - - - - - - - - - - - - - - - - - -
Extracting /usr (except /usr/sys). This
takes about 5-10 minutes
Finished
Extracting system source. This takes
about 5-10 minutes
Finished
Checking the consistency of the /usr filesystem
on ra0g
** /dev/rra0g
** Last Mounted on /usr
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
789 files, 7555 used, 70204 free (140 frags, 8758 blocks)
Please remove the installation volume from the
installation drive and put it in a safe place.
You are through with it for this installation.
You will extract files from the rest of the kit
later in the procedure.
The DIGITAL recommended partition for the
/usr/users filesystem on an ra81 is h.
This partition on ra0 will be cleared by
these procedures.
* * * Making filesystem for /usr/users on ra0h * * *
Warning: 28 sector(s) in last cylinder unallocated
/dev/rra0h: 759668 sectors in 1064 cylinders of 14 tracks, 51 sectors
389.0Mb in 67 cyl groups (16 c/g, 5.85Mb/g, 2048 i/g)
super-block backups (for fsck -b#) at:
32, 11512, 22992, 34472, 45952, 57432, 68912, 80392, 91872, 103352,
114832, 126312, 137792, 149272, 160752, 172232, 182816, 194296, 205776, 217256,
228736, 240216, 251696, 263176, 274656, 286136, 297616, 309096, 320576, 332056,
343536, 355016, 365600, 377080, 388560, 400040, 411520, 423000, 434480, 445960,
457440, 468920, 480400, 491880, 503360, 514840, 526320, 537800, 548384, 559864,
571344, 582824, 594304, 605784, 617264, 628744, 640224, 651704, 663184, 674664,
686144, 697624, 709104, 720584, 731168, 742648, 754128,
* * * Initializing /etc/fstab * * *
* * * Making the /usr/users directory * * *
* * * Clearing the mount table * * *
* * * Checking the filesystems * * *
** /dev/ra0a
** Last Mounted on /
** Root file system
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
716 files, 3872 used, 3557 free (21 frags, 442 blocks)
** /dev/rra0g
** Last Mounted on /usr
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
790 files, 7556 used, 70203 free (139 frags, 8758 blocks)
** /dev/rra0h
** Last Mounted on
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2 files, 5 used, 361855 free (7 frags, 90462 blocks)
* * * Listing Free Space on all Filesystems
Filesystem total kbytes kbytes percent
node kbytes used free used Mounted on
/dev/ra0a 7429 3873 2813 58% /
/dev/ra0g 38879 3778 31213 11% /usr
/dev/ra0h 361860 5 325669 0% /usr/users
* * * Automatic Crash Dump Query * * *
Would you like to enable automatic crash
dumps (y/n) [y]? y
* * * System Configuration Dialogue * * *
Enter the name of your system (only capital letters) [no default]: ULTVAX
You entered ULTVAX. Is this
correct (y/n) [y]? y
Should the running system have this name?
(i.e., should rc.local be changed to
make ultvax the hostname?) (y/n) (y): y
System is now called ultvax
Enter the Time Zone for your area. Choices for
the time zone are:
Eastern (e)
Central (c)
Mountain (m)
Pacific (p)
Greenwich (g)
or number of hours (in time) west of Greenwich.
Enter the Time Zone (e, c, m, p, g, # of hours): c
Does your area alternate between Daylight Savings
and Standard time [yes] ? yes
Enter Geographic area for Daylight Savings Time.
Choices are:
USA (u)
Australia (a)
Eastern Europe (e)
Central Europe (c)
Western Europe (w)
Enter the Geographic area (u, a, e, c, w) [u]: w
A configuration file has been created for the
devices this program has determined are present.
The configuration file is as follows:
ident ULTVAX
machine vax
cpu "VAX780"
maxusers 32
maxuprc 25
physmem 8
timezone 6 dst 3
options INET
options QUOTA
config vmunix root on ra0a swap on ra0b dumps on ra0b args on ra0b
controller uba0 at nexus ?
controller uda0 at uba0 csr 0172150 vector udintr
disk ra0 at uda0 drive 0
device de0 at uba0 csr 0174510 vector deintr
device lp0 at uba0 csr 0177514 vector lpintr
controller mba0 at nexus ?
master ht0 at mba0 drive 0
tape tu0 at ht0 slave 0
pseudo-device pty
psuedo-device loop
psuedo-device inet
psuedo-device ether
You need to add a communication device to the
configuration file. You may also add other
devices that were not found by this program.
You will be asked to enter information about the
device(s) you wish to add to the configuration file.
Entering 'exit' in response to the first prompt will
terminate this portion of the configuration process.
Typing 'erase' will delete previously entered data for
the current device and return to the first prompt.
If the device(s) you choose are supported by Digital,
the name of the appropriate interrupt routines will
be supplied by the program.
First, enter the name of the device you wish to
add. A device name is the name used by Digital to
identify the device.
Be sure to use the ULTRIX-32 name listed in
section 4 of the ULTRIX-32 SYSTEM MANAGERS guide.
The device name also includes the logical number of
the device.
For example, 'hp0' is an RM05 disk drive that is the
first 'hp' type drive on the system.
Enter the device name, ?, or 'exit' --->exit
Configuration file complete
Do you wish to edit the configuration
file (y/n) [y]? n
* * * Performing the System Configuration * * *
grep '^#include' ../net/conf_net.c ../netinet/in_proto.c ../vax/conf.c ../data/ht_data.c ../data/lp_data.c ../data/uda_data.c ../data/if_de_data.c ../data/tty_pty_data.c ../data/af_data.c ../data/tty_conf_data.c ../data/uipc_domain_data.c ../data/autoconf_data.c ../data/if_to_proto_data.c | grep -v '<' | sed -e 's/:[^"]*"\([^"]*\)".*/: \1/' -e 's/\.c/.o/' -e 's,../[a-zA-Z]*/,,' >xtmp
awk ' { if ($1 != prev) { print rec; rec = $0; prev = $1; } else { if (length(rec $2) > 78) { print rec; rec = $0; } else rec = rec " " $2 } } END { print rec } ' > makedep <xtmp
rm -f xtmp
echo '/^# DO NOT DELETE THIS LINE/+1,$d' >eddep
echo '$r makedep' >>eddep
echo 'w' >>eddep
cp makefile makefile.bak
ed - makefile < eddep
rm eddep makedep
cat assym.s ../vax/spt.s > spt.c
cc -E -I. -DLOCORE -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 spt.c > spt.i
as -o spt.o ${AHEADS} spt.i
ld -r locore_bin.o spt.o
cat assym.s ubglue.s > ubglue.c
cc -E -I. -DLOCORE -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ubglue.c > ubglue.i
as -o ubglue.o ${AHEADS} ubglue.i
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../net/conf_net.c
/lib/c2 conf_net.s | ../vax/asm | as -o conf_net.o
rm -f conf_net.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../netinet/in_proto.c
/lib/c2 in_proto.s | ../vax/asm | as -o in_proto.o
rm -f in_proto.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../vax/conf.c
/lib/c2 conf.s | ../vax/asm | as -o conf.o
rm -f conf.s
touch -f -c ../h/ioctl.h
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/ht_data.c
/lib/c2 -i ht_data.s | ../vax/asm | as -o ht_data.o
rm -f ht_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/lp_data.c
/lib/c2 -i lp_data.s | ../vax/asm | as -o lp_data.o
rm -f lp_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/uda_data.c
/lib/c2 -i uda_data.s | ../vax/asm | as -o uda_data.o
rm -f uda_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/if_de_data.c
/lib/c2 -i if_de_data.s | ../vax/asm | as -o if_de_data.o
rm -f if_de_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/tty_pty_data.c
/lib/c2 tty_pty_data.s | ../vax/asm | as -o tty_pty_data.o
rm -f tty_pty_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/af_data.c
/lib/c2 af_data.s | ../vax/asm | as -o af_data.o
rm -f af_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/tty_conf_data.c
/lib/c2 tty_conf_data.s | ../vax/asm | as -o tty_conf_data.o
rm -f tty_conf_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/uipc_domain_data.c
/lib/c2 uipc_domain_data.s | ../vax/asm | as -o uipc_domain_data.o
rm -f uipc_domain_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/autoconf_data.c
/lib/c2 autoconf_data.s | ../vax/asm | as -o autoconf_data.o
rm -f autoconf_data.s
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ../data/if_to_proto_data.c
/lib/c2 if_to_proto_data.s | ../vax/asm | as -o if_to_proto_data.o
rm -f if_to_proto_data.s
cp ../conf/param.c .
cc -I. -c -O -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 -DTIMEZONE=360 -DDST=3 -DMAXUSERS=32 -DMAXUPRC=25 -DPHYSMEM=8 -DDMMIN=32 -DDMMAX=1024 param.c
cc -I. -c -S -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 ioconf.c
/lib/c2 ioconf.s | ../vax/asm | as -o ioconf.o
rm -f ioconf.s
cc -I. -c -O -DULTVAX -DBINARY -DVAX780 -DQUOTA -DINET -DKERNEL -DUPGRADE=0 swapvmunix.c
loading vmunix
rearranging symbols
text data bss dec hex
180728 75908 35932 292568 476d8
* * * Make the Special Files for the System * * *
MAKEDEV ra0 lp0 tu0 pty0 pty1 std
special files for tu0 are *mt{0,4,8,12}
* * * Configured kernel is in /newvmunix * * *
What will follow is the sequence of steps that you
must take to boot the newly configured ULTRIX
kernel.
If, after booting this kernel, you decide that you
need to reconfigure the kernel. Execute the
command:
doconfig
and peform the booting steps, shown below, again.
If the kernel is properly configured, then be sure
to save the old kernel and move the new kernel to
/vmunix, as follows:
mv /vmunix /oldvmunix
mv /newvmunix /vmunix
---------------------------
When you are told the system is ready to be
halted, perform the following steps:
1) Type the following:
^P (get the attention of the
console subsystem)
H (halt the processor)
U (unjam the SBI
I (initialize the processor)
2) B ANY
3) Respond to 'Boot:' with--
ra(0,0)newvmunix
syncing disks... done
THE PROCESSOR CAN NOW BE HALTED.
Infinite loop, PC: 80023BC4 (BRB 80023BC4)
sim>
Boot Ultrix V1.1 with New Kernel and install software subsets
sim> DEP R11 3
sim> FLOAD BOOT 0
sim> RUN 2
Resetting all devices... This may not have been your intention.
The GO and CONTINUE commands do not reset devices.
Boot
: ra(0,0)newvmunix
180728+75908+35932 start 0x1420
Ultrix V1.1 System #1: Thu Jun 13 21:27:09 EDT 1985
real mem = 8384512
avail mem = 6904832
using 305 buffers containing 838656 bytes of memory
VAX 11/780, serial no. 1234, hardware level = 7
mcr0 (MS780-C) at address 0x20002000, 4096Kbytes, noninterleaved
mcr1 (MS780-C) at address 0x20004000, 4096Kbytes, noninterleaved
uba0 at address 0x20006000
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
de0 at uba0 csr 174510 vec 120, ipl 15
lp0 at uba0 csr 177514 vec 200, ipl 14
mba0 at address 0x20010000
ht0 at mba0 drive 0
tu0 at ht0 slave 0
WARNING: clock gained 10 days -- CHECK AND RESET THE DATE!
erase ^?, kill ^U, intr ^C
# ls -l
total 1056
-rwxr--r-- 1 root 211 May 9 10:09 .cshrc
-rwxr--r-- 1 root 90 May 9 10:09 .login
-rwxr--r-- 1 root 169 May 9 10:09 .profile
-rwxr--r-- 1 root 48 May 9 10:09 .rhosts
drwxr-xr-x 2 root 1024 May 9 08:50 bin
-rwxr-xr-x 1 root 21956 May 9 09:44 boot
drwxr-xr-x 2 root 2048 Jun 13 20:27 dev
drwxr-xr-x 2 root 2560 Jun 13 20:26 etc
-rwxr-xr-x 1 root 334848 May 9 09:43 genvmunix
drwxr-xr-x 2 root 512 May 9 08:52 lib
drwxr-xr-x 2 root 24 May 9 08:23 lost+found
drwxr-xr-x 2 root 24 May 9 09:53 mnt
-rwxr-xr-x 1 root 286720 Jun 13 20:27 newvmunix
drwxr-xr-x 2 root 7696 Jun 13 20:26 olddev
drwxr-xr-x 2 root 512 May 9 09:10 opr
-rwxr-xr-x 1 root 11264 May 9 09:52 pcs750.bin
-rw-rw-rw- 1 root 37072 Jun 24 04:01 restoresymtable
lrwxrwxrwx 1 root 7 Jun 24 04:01 sys -> usr/sys
drwxrwxrwx 2 root 512 Jun 13 20:27 tmp
drwxr-xr-x 2 root 512 May 9 09:43 tp
drwxr-xr-x 2 root 24 May 9 08:24 usr
-rwxr-xr-x 1 root 334848 May 9 09:43 vmunix
# mv /newvmunix /vmunix
# ls -l
total 720
-rwxr--r-- 1 root 211 May 9 10:09 .cshrc
-rwxr--r-- 1 root 90 May 9 10:09 .login
-rwxr--r-- 1 root 169 May 9 10:09 .profile
-rwxr--r-- 1 root 48 May 9 10:09 .rhosts
drwxr-xr-x 2 root 1024 May 9 08:50 bin
-rwxr-xr-x 1 root 21956 May 9 09:44 boot
drwxr-xr-x 2 root 2048 Jun 13 20:27 dev
drwxr-xr-x 2 root 2560 Jun 13 20:26 etc
-rwxr-xr-x 1 root 334848 May 9 09:43 genvmunix
drwxr-xr-x 2 root 512 May 9 08:52 lib
drwxr-xr-x 2 root 24 May 9 08:23 lost+found
drwxr-xr-x 2 root 24 May 9 09:53 mnt
drwxr-xr-x 2 root 7696 Jun 13 20:26 olddev
drwxr-xr-x 2 root 512 May 9 09:10 opr
-rwxr-xr-x 1 root 11264 May 9 09:52 pcs750.bin
-rw-rw-rw- 1 root 37072 Jun 24 04:01 restoresymtable
lrwxrwxrwx 1 root 7 Jun 24 04:01 sys -> usr/sys
drwxrwxrwx 2 root 512 Jun 13 20:27 tmp
drwxr-xr-x 2 root 512 May 9 09:43 tp
drwxr-xr-x 2 root 24 May 9 08:24 usr
-rwxr-xr-x 1 root 286720 Jun 13 20:27 vmunix
# [STRG + d]
Mon Jun 24 04:08:08 CDT 1985
check quotas: done.
local daemons: routed telnetd ftpd talkd syslog.
preserving editor files
clearing /tmp
standard daemons: update cron accounting mail printer.
starting network: rshd rexecd rlogind rwhod.
Mon Jun 24 04:08:09 CDT 1985
Ultrix-32 V1.1 (ultvax)
login: root
Password: ult011 (not echoed)
Digital Equipment Corporation
Merrimack, New Hampshire.
# cat /usr/sys/conf/ULTVAX
ident ULTVAX
machine vax
cpu "VAX780"
maxusers 32
maxuprc 25
physmem 8
timezone 6 dst 3
options INET
options QUOTA
config vmunix root on ra0a swap on ra0b dumps on ra0b args on ra0b
controller uba0 at nexus ?
controller uda0 at uba0 csr 0172150 vector udintr
disk ra0 at uda0 drive 0
device de0 at uba0 csr 0174510 vector deintr
device lp0 at uba0 csr 0177514 vector lpintr
controller mba0 at nexus ?
master ht0 at mba0 drive 0
tape tu0 at ht0 slave 0
pseudo-device pty
pseudo-device loop
pseudo-device inet
pseudo-device ether
# cd /etc
# sh instmedia tape
Please mount the tape volume that contains the ULTRIX software
subsets.
Press RETURN when the unit is online and ready:
[STRG + e]
Simulation stopped, PC: 800017C2 (TSTL 8003EE28)
sim> ATT TU0 ultrix-32_1.1_opt_sw_2of2.tap
%SIM-INFO: TU0: Tape Image 'ultrix-32_1.1_opt_sw_2of2.tap' scanned as SIMH format
sim> C
[Enter]
Here are the software subsets that you may now load into your
ULTRIX-32 system. Note that those sets marked with a '*' are
required subsets and will be loaded automatically.
1) BASUTIL* Basic ULTRIX-32 utilities package
2) F77 The FORTRAN-77 language
3) LISP The LISP and FP languages
4) PASCAL The PASCAL language
5) MODULA2 The Modula-2 language
6) GAMES The usual array of fun and recreation
7) SELFHLP Self Help programs (LEARN)
8) MANDOC Documentation: /usr/man directories
9) CONTRIB User Contributed Software
10) AUXDOC Documentation: /usr/doc directories
11) VARIAN Fonts and Varian Plotter programs
Please specify ALL of the subsets that you wish to load by number.
If you would like more detailed descriptions, type 'help'
For example, the selections: 1 2 4
would cause subsets BASUTIL F77 and PASCAL to be loaded.
and the selection: help
would cause a more detailed help message to be displayed
for each entry.
Please enter your selections: 1 2 3 4 5 6 7 8 9 10 11
You chose to add the following: BASUTIL F77 LISP PASCAL MODULA2 GAMES SELFHLP MANDOC CONTRIB AUXDOC VARIAN
Is this correct (y/n) [n]: y
Skipping 1 fileset. . .
Loading BASUTIL. . .Finished
Skipping 1 fileset. . .
Loading F77. . .Finished
Skipping 1 fileset. . .
Loading LISP. . .Finished
Skipping 1 fileset. . .
Loading PASCAL. . .Finished
Skipping 1 fileset. . .
Loading MODULA2. . .Finished
Skipping 1 fileset. . .
Loading GAMES. . .Finished
Skipping 1 fileset. . .
Loading SELFHLP. . .Finished
Skipping 1 fileset. . .
Loading MANDOC. . .Finished
Skipping 1 fileset. . .
Loading CONTRIB. . .Finished
Skipping 1 fileset. . .
Loading AUXDOC. . .Finished
Skipping 1 fileset. . .
Loading VARIAN. . .Finished
Rewinding tape
Cleaning up.
# df
Filesystem total kbytes kbytes percent
node kbytes used free used Mounted on
/dev/ra0a 7429 3743 2943 56% /
/dev/ra0g 38879 33199 1792 95% /usr
/dev/ra0h 361860 5 325669 0% /usr/users
# /etc/netsetup install
Whenever a default selection is given for a question
[shown in square brackets] you only need to press
the <RETURN> key to select the default choice.
Enter an abbreviation for ultvax (for example the 1st letter): u
Are you configuring your system on a network [no] ? yes
Enter the network number for your network: 10
Enter the system number on the network for ultvax: 200
Enter the network name [ethernet]: ethernet
Enter the network alias [deunanetworks]: deunanetworks
Setting up '/etc/networks' file.
Enter the system name, abbreviation, and system number, for each
computer on the network. Enter these on separate lines when prompted.
This information is put into the '/etc/hosts' file.
Enter the name of the 1st system to put on your network
(<RETURN> only if no more to enter): pc
Enter the abbreviation for PC: p
Enter the system number on the network for PC: 1
Enter the name of the next system to put on your network
(<RETURN> only if no more to enter): [Enter]
Enter the names of 'trusted' systems. Trusted systems are
computers considered to be secure. Users on any trusted systems
can login to your system without password verification on your
system. Such users must have a valid account on the 'trusted'
system. This information is put in the '/etc/hosts.equiv' file.
Enter the full name of the first 'trusted' system
(<RETURN> only if none): [Enter]
Network setup is finished.
# shutdown -h now
Shutdown at 04:18 (in 0 minutes) [pid 414]
System shutdown time has arrived
# syncing disks... done
THE PROCESSOR CAN NOW BE HALTED.
Infinite loop, PC: 80023B18 (BRB 80023B18)
sim>
Boot Ultrix V1.1
sim> DEP R10 9
sim> DEP R11 0
sim> FLOAD BOOT 0
sim> RUN 2
Resetting all devices... This may not have been your intention.
The GO and CONTINUE commands do not reset devices.
Boot
: ra(0,0)vmunix
180728+75908+35932 start 0x1420
Ultrix V1.1 System #1: Thu Jun 13 21:27:09 EDT 1985
real mem = 8384512
avail mem = 6904832
using 305 buffers containing 838656 bytes of memory
VAX 11/780, serial no. 1234, hardware level = 7
mcr0 (MS780-C) at address 0x20002000, 4096Kbytes, noninterleaved
mcr1 (MS780-C) at address 0x20004000, 4096Kbytes, noninterleaved
uba0 at address 0x20006000
uda0 at uba0 csr 172150 vec 774, ipl 15
ra0 at uda0 slave 0
de0 at uba0 csr 174510 vec 120, ipl 15
lp0 at uba0 csr 177514 vec 200, ipl 14
mba0 at address 0x20010000
ht0 at mba0 drive 0
tu0 at ht0 slave 0
Automatic reboot in progress...
Mon Jun 24 04:15:49 CDT 1985
/dev/ra0a: 809 files, 3743 used, 3686 free (22 frags, 458 blocks)
/dev/rra0g: 3702 files, 66402 used, 11357 free (69 frags, 1411 blocks)
/dev/rra0h: 2 files, 5 used, 361855 free (7 frags, 90462 blocks)
Mon Jun 24 04:15:53 CDT 1985
check quotas: done.
local daemons: routed telnetd ftpd talkd syslog sendmail.
preserving editor files
clearing /tmp
standard daemons: update cron accounting mail printer.
starting network: rshd rexecd rlogind rwhod.
Mon Jun 24 04:15:55 CDT 1985
Ultrix-32 V1.1 (ultvax)
login: root
Password: ult011 (not echoed)
Digital Equipment Corporation
Merrimack, New Hampshire.
# ps -axl
F UID PID PPID CP PRI NI ADDR SZ RSS WCHAN STAT TT TIME COMMAND
3 0 0 0 0 -25 0 23e 0 0 3f296 D ? 0:00 swapper
1008001 0 1 0 0 5 0 bda 23 5 c3b18 S ? 0:00 init
1000003 0 2 0 0 -24 0 bce2432 0 c3bb8 D ? 0:00 pagedaemon
1008001 0 42 1 0 1 0 110c 51 6 8e360 S ? 0:00 /etc/ftpd
1008001 0 46 1 0 1 0 10ec 40 8 8e0b0 S ? 0:00 /etc/talkd
1008001 0 47 1 0 1 0 10d0 44 7 8df60 S ? 0:00 /etc/telnet
1008001 1 51 1 0 1 0 107c 50 11 8e1b0 S ? 0:00 /etc/syslog
1008001 0 53 1 0 1 0 105e 53 29 3f2b8 S ? 0:00 /etc/routed
1008201 0 64 1 0 15 0 fb0 20 2 fec00 S ? 0:00 /etc/update
1008201 0 67 1 0 15 0 f94 25 5 fec00 S ? 0:00 /etc/cron
1008001 0 80 1 0 1 0 f54 41 7 9c5b0 S ? 0:00 /etc/comsat
1008001 0 88 1 0 1 0 f1c 50 11 3f2b8 S ? 0:00 /usr/lib/lp
1008001 0 95 1 0 1 0 eaa 43 7 8d860 S ? 0:00 /etc/rshd
1008001 0 98 1 0 1 0 e72 43 8 8d7e0 S ? 0:00 /etc/rexecd
1008001 0 101 1 0 1 0 e44 40 6 8d660 S ? 0:00 /etc/rlogin
1008001 0 104 1 0 1 0 d4e 51 25 9c730 S ? 0:00 /etc/rwhod
1008201 0 107 1 0 15 0 c00 36 17 fec00 S co 0:00 -csh (csh)
1008001 0 108 1 0 1 0 da4 98 63 8d4e0 S ? 0:00 /usr/lib/se
1008001 0 112 107 11 27 0 fee 116 61 R co 0:00 ps -axl
# ifconfig de0
de0: 10.0.0.200 flags=243<UP,BROADCAST,RUNNING>
# shutdown -h now
Shutdown at 04:16 (in 0 minutes) [pid 115]
System shutdown time has arrived
syncing disks... done
THE PROCESSOR CAN NOW BE HALTED.
Infinite loop, PC: 80023B18 (BRB 80023B18)
sim> exit
Goodbye
Log file closed
