DS11 Multiple Line Synchronous Interface

From Computer History Wiki
Revision as of 17:38, 5 January 2024 by Jnc (talk | contribs) (→‎Interrupt vector: Add)
Jump to: navigation, search

The DS11 Multiple Line Synchronous Interface was an early synchronous serial line interface for the UNIBUS; it could handle up to 16 lines. It used programmed I/O (with separate receive and transmit interrupts) to transfer data; it could operate in either half-duplex or full-duplex mode.

Character lengths of 6, 8 and 12 bits were supported, and could be configured by software. It provided an EIA RS-232 interface to Bell 200 series modems (such as the model 201, and equivalents), and also connect to Bell 300 series modems, such as the model 303.

Registers

Register Abbreviation Address
Receiver Status Register RxCSR 775xx0
Receiver Data Buffer Register RxDBUF 775xx2
Transmitter Status Register TxCSR 775xx4
Transmitter Data Buffer Register TxDBUF 775xx6
Interface Status Register ISTR 775600

Line addresses:

  • Line 0: 775400-775406
...
  • Line 15: 775570-775576

In the register contents (below), bits which are read/write or unused are shown in normal font, those which are read-only are in italics, and write-only in bold.

175xx0: Receiver Status Register (RxCSR)

RING BITOVR CHAROVR CARLST SYNCST CARDET DTR DONE DSR CHARLEN DNIA RNGENB RCVENB
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • BITOVR - Bit Overrun
  • CHAROVR - Character Overrun
  • CARLST - Carrier Lost
  • SYNCST - Sync State
  • CARDET - Carrier Detected
  • DTR - Data Terminal Ready
  • DSR - Data Set Ready
  • CHARLEN - Character Length
  • DNIA - Done Interrupt Assignment
  • RNGENB - Ring Enable
  • RCVENB - Receiver Enable

175xx2 (read): Receiver Data Buffer Register (RxDBUF)

Unused RDBUF
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • RDBUF - Receiver Data Buffer

175xx4: Transmitter Status Register (TxCSR)

Unused BITOVR CHAROVR CTSLST Unused CTS DTR DONE DSR CHARLEN DNIA IDLE RTS
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • BITOVR - Bit Overrun
  • CHAROVR - Character Overrun
  • CTSLST - Clear to Send Lost
  • CTS - Clear to Send
  • DTR - Data Terminal Ready
  • DSR - Data Set Ready
  • CHARLEN - Character Length
  • DNIA - Done Interrupt Assignment
  • RTS - Request to Send

175xx6: Transmitter Data Buffer Register (TxDBUF)

Unused TDBUF
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • TDBUF - Transmitter Data Buffer

175600: Interface Status Register (ISTR)

A3IN A2IN A1IN Unused VAHBITS DIAGM PRCLK Unused CLRBC DIAGBC
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • A3IN - Adapter 3 In
  • A2IN - Adapter 2 In
  • A1IN - Adapter 1 In
  • VAHBITS - Vector Address High Bits
  • DIAGM - Diagnostic Mode
  • PRCLK - Program Clock
  • CLRBC - Clear Bit Counter
  • DIAGBC - Diagnostic Bit Counter

Interrupt vector

The DS11 uses an array of interrupt vectors, as follows:

Unused VAHBITS LINE TINT STINT 0
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • VAHBITS - Vector Address High Bits
  • LINE - Line Number
  • TINT - Transmitter Interrupt
  • STINT - Status Interrupt

Implementation

The DS11 consisted of a master line scanner, and up to four adapters, each of which could handle up to four lines; each line had a separate quad M7110 Line Control Module. Physically, it is a large quad-height backplane, mounted in a 19" cabinet such as an H950, along with the DS11's DEC indicator panel.

The DS11, like some other early UNIBUS peripherals, was made of many small FLIP CHIPs. The inventory of the card types in the DS11 is:

  • G830 5V, 10A Regulator from 8V
  • M002 Resistor network
  • M126 6 x AND-NOR Gates
  • M128 4,4 AND-NOR Gates
  • M139 3 x 8-Input NAND Gates
  • M143 10 x 2-Input NAND Gates
  • M145 7 x 3-Input NAND Gates
  • M147 5 x 4-Input, 1 x 2-Input NAND Gates
  • M152 Dual Non-inverting Binary to Octal with Enable
  • M165 Memory buffer, Inverting and Non-inverting Output
  • M171 2-2-2-3 AND-NOR
  • M173 10 x 2-input AND gates
  • M174 4 En x 9 out mixer
  • M175 7 x 3-input AND gates
  • M177 5 x 4-Input AND Gates
  • M178 8 En x 6 out mixer
  • M181 Non-inverting 2-2-2-3 AND-NOR
  • M211 6-Bit Up/Down Counter
  • M241 6 x D Flip-flops with common clock
  • M243 8 x D Flip-flops with 2 common clocks
  • M246 5 x D Flip-Flops
  • M253 16 Word, 12-bit Memory
  • M307 Integrating One Shot
  • M321 Tapped Delay Line
  • M362 Delay, 25 to 50 ns
  • M401 Variable Clock
  • M603 Pulse Amplifiers
  • M612 6 Power Gates
  • M783 UNIBUS Drivers
  • M784 UNIBUS Receiver
  • M785 UNIBUS Transceiver
  • M931 15 Terminators
  • M969 24 Level Terminators
  • M511 UNIBUS Receivers - sources differ as to whether or not this is used
  • W990 Connectors
  • M105 Address Selector - used to set its bus address
  • M7820 Interrupt Control
  • M7110 Line Control Module - one per line

The number of each type used is currently unknown; likewise the locations in the backplane (except the M7110's)

See also

Further reading

  • DS11 Multiple Line Synchronous Interface Maintenance Manual (DEC-00-DS11-DB; not available online, but in fiche)

External links

Retrieved from "https://gunkies.org/w/index.php?title=DS11_Multiple_Line_Synchronous_Interface&oldid=32544"