Difference between revisions of "DHQ11 asynchronous serial line interface"

From Computer History Wiki
Jump to: navigation, search
(An OK start)
 
(Implementation: two variants)
Line 5: Line 5:
 
==Implementation==
 
==Implementation==
  
Physically, the DHQ11 consisted of a single [[DEC card form factor|dual]] card, the M3107, connected to a pair of H3173-A distribution panels (4 lines each) via a BC05L [[flat cable]], one per distribution panel; the BC05L connects to a 40-pin [[Berg connector|Berg header]] on each end. The H3173-A can be recognized by the [[Digital Equipment Corporation|DEC]] part number 50-15588-01 on its [[printed circuit board|PCB]]; each contains four male [[EIA RS-232 serial line interface#Connectors|DB-25 connectors]] (DB-25P). In addition to the usual '-xx' length indicators on the BC05L cable, it was also available in BC05L-1K (21 inch) and BC05L-2F (30 inch) lengths.
+
Physically, the DHQ11 consisted of a single [[DEC card form factor|dual]] card, the M3107, connected to a pair of H3173-A distribution panels (4 lines each) via a BC05L [[flat cable]], one per distribution panel; the BC05L connects to a 40-pin [[Berg connector|Berg header]] on each end. The H3173-A can be recognized by the [[Digital Equipment Corporation|DEC]] part number 50-15588-01 or -02 on its [[printed circuit board|PCB]]; each contains four male [[EIA RS-232 serial line interface#Connectors|DB-25 connectors]] (DB-25P). In addition to the usual '-xx' length indicators on the BC05L cable, it was also available in BC05L-1K (21 inch) and BC05L-2F (30 inch) lengths.
  
 
==Device registers==
 
==Device registers==

Revision as of 10:36, 31 December 2020

The DHQ11 asynchronous serial line interface is the second QBUS equivalent to the UNIBUS DH11 (it a replacement for the DHV11). It provided 8 RS-232 asynchronous serial lines. Output used DMA (with each line having its own buffer pointer and count); input used a 64-character FIFO buffer.

It can be set (via a switch) to emulate either a DHV11 or DHU11.

Implementation

Physically, the DHQ11 consisted of a single dual card, the M3107, connected to a pair of H3173-A distribution panels (4 lines each) via a BC05L flat cable, one per distribution panel; the BC05L connects to a 40-pin Berg header on each end. The H3173-A can be recognized by the DEC part number 50-15588-01 or -02 on its PCB; each contains four male DB-25 connectors (DB-25P). In addition to the usual '-xx' length indicators on the BC05L cable, it was also available in BC05L-1K (21 inch) and BC05L-2F (30 inch) lengths.

Device registers

The registers will depend on whether it is emulating a DHV11 or DHU11.

Control and Status Register (CSR)

In DHU11 mode, the CSR is:

TXA TXIE DF TDE Unused Tx Line RDA RXIE MR SKIP Unused Line
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
  • TXA - Transmitter Action
  • TXIE - Transmit Interrupt Enable
  • DF - Diagnostic Fail
  • TDE - Transmit DMA Error
  • Tx Line - Line which set TXA
  • RDA - Received Data Available
  • RXIE - Receive Interrupt Enable
  • MR - Master Reset
  • SKIP - Skip Self-Test
  • Line - Select TXC through TBCT

Further reading

  • DHQ11 User Guide, EK-DHQ11-UG-002