Installing, Configuring, and Testing A VMS V4.7 Local Area VAXcluster on SIMH
From Computer History Wiki
The aim of this tutorial is to show how to install a VMS V4.7 Local Area VAXcluster (short: LAVC) on the SIMH MicroVAX II simulator.
Contents
Local Area VAXclusters
Today's Advantages of Local Area VAXclusters
Two common problems:
- You own a MicroVAX or VAXstation without a working disk
- You have no load device (e.g. tape or CDROM drive) to install software on your MicroVAX or VAXstation
A Local Area VAXcluster built with a SIMH simulator is the perfect solution for this problems:
- You can run your MicroVAX or VAXstation diskless
- You can install software on your MicroVAX or VAXstation disk
And if you use a Raspberry Pi instead of a normal PC for your SIMH host, you will save a lot of electric energy!
It doesn't matter whether you boot real MicroVAXen or VAXstations or SIMH simulated ones from your VAXcluster; there is no difference except for speed (the SIMH VAXen are faster).
Local Area VAXcluster Vocabulary
- Boot Node = LAVC Server
- Satellite Node = LAVC Client
Introduction to Local Area VAXclusters
A Local Area VAXcluster configuration consists of one or two boot nodes and up to 26 satellite nodes.
A boot node is both a management center for the cluster and a major resource provider. Its system disk contains the cluster common files for startup, authorization, and queue setup, as well as the directory roots from which the satellite nodes are booted.
A boot node makes available to the cluster such resources as user and application data disks, printers, and distributed batch processing facilities.
In a Local Area VAXcluster configuration, a boot node may be any VAX system except VAX-11/725 or VAX-11/730, or it may be one of the following MicroVAX II or VAXstation II systems:
- MicroVAX II with an RA series system disk.
- MicroVAX II with an RD54 system disk, or VAXstation II with an RD54 or any larger system disk. Note that these boot nodes support a maximum of three satellites. In addition, it is recommended that the satellites use local RD series disks for paging and swapping.
The satellite nodes are booted remotely from a boot node's system disk.
Generally, these nodes are consumers of cluster resources, though they may also sometimes provide disk serving and batch processing resources.
If satellite nodes are equipped with RD series disks, they may, for enhanced performance, use such local disks for paging and swapping.
Satellite nodes may be any of the following:
- MicroVAX II
- MicroVAX 2000
- VAXstation II
- VAXstation 2000
- VAXstation II/GPX
- VAXstation II/RC
Caution
All MicroVAX II and VAXstation II machines in a Local Area VAXcluster configuration must use Revision E (or later) QBUS Network Adapter (DEQNA) devices and must have at least 3MB memory. Diskless machines require at least 4MB memory.
Preparations
Suitable SIMH VAX simulators
As boot node I chose the SIMH microvax2 simulator because this was the cheapest way to build a Local Area VAXcluster from new in 1987.
If you already had a "big" VAX back then with enough disk space available you could use that one, too, of course.
I decided to use VMS V4.7 as there is no hassle with "License PAKs", but this restricts the choice of VAXen for boot and satellite nodes (see above).
There will probably be a tutorial for VMS V5.5-2H2 and/or VMS V6.2 Local Area VAXclusters in the near future, too.
VMS Versions needed
To install VMS V4.7 (which is an update version only) you have to start with VMS V4.6 which is a full version.
Get all the software needed (and a manual) here.
microvax2.ini for the Boot Node (a Typical Large MicroVAX II System)
; ================================================ ; microvax2.ini ; ================================================ ; ; Large MicroVAX II system made of: ; - 16 MB memory ; - 1 DZV11 terminal multiplexer with 4 lines ; - 1 RQDX3 disk/floppy controller ; - 1 RA82 disk drive ; - 1 RX50 dual floppy disk drive ; - 1 TKQ50 tape cassette drive controller ; - 1 TK50 tape cassette drive ; - 1 DELQA Ethernet adapter SET QUIET SET CPU 16M SET CPU IDLE=VMS SET CPU CONHALT SET CPU AUTOBOOT ATT NVR NVR-MVII.BIN SET CONSOLE LOG=VMS_V4.7_LAVC.LOG SET RQ ENA SET RQ0 RA82 ATT RQ0 -F VHD VMS047_VHD.R82 SET RQ1 RX50 SET RQ2 RX50 SET RQ3 DIS SET DZ LINES=4 ;ATT DZ 6666 SET TQ ENA ATT TQ0 staba046.tap SET TQ1 DIS SET TQ2 DIS SET TQ3 DIS SET LPT DIS SET RL DIS SET TS DIS SET XQ ENA SET XQ TYPE=DELQA ;SET XQ MAC=08-00-2B-0B-18-1A ;ATT XQ eth0 BOOT
Installation
Start the SIMH MicroVAX II Simulator
Windows:
run microvax2.exe
Linux:
./microvax2
Be aware that Linux is case sensitive!
Boot VMS V4.6 Standalone Backup
sim> BOOT KA630-A.V1.3 Performing normal system tests. 5..4..3.. Tests completed. >>> B MUA0 2..1..0.. MicroVMS Version V4.6 6-Jul-1987 17:00 PLEASE ENTER DATE AND TIME (DD-MMM-YYYY HH:MM) 21-JUL-2022 14:37 %BACKUP-I-IDENT, Stand-alone BACKUP V4.6; the date is 21-JUL-2022 14:37:02.63 $
Restore VMS V4.6 REQUIRED Saveset
$ [STRG + e] Simulation stopped, PC: 80008B1F (BRB 80008B1F) sim> ATT TQ0 BB-BT05D-BE_VMS4.6_87.tap sim> C $ $ BACKUP/LOG/VERIFY MUA0:REQUIRED/SAVE DUA0: %BACKUP-S-CREATED, created DUA0:[000000]000000.DIR;1 %BACKUP-S-CREATED, created DUA0:[000000]BACKUP.SYS;1 %BACKUP-S-CREATED, created DUA0:[000000]CONTIN.SYS;1 %BACKUP-S-CREATED, created DUA0:[000000]CORIMG.SYS;1 %BACKUP-S-CREATED, created DUA0:[000000]SYS0.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]MOM$SYSTEM.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSCBI.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSERR.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSERR]ERRSNAP.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSEXE.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]BACKUP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]BADBLOCK.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CLUSTRLOA.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CNDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CONFIGURE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CONINTERR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]COPY.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CRDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CREATE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CSP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CVDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]CWDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DBDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DCL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DDDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DELETE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DIRECTORY.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DISMOUNT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DLDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DMDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DQDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DRDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DUDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DVDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DXDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DYDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]DZDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]ERRFMT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]ERRSNAP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]ESDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]ETDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]F11BXQP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]FILESERV.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]FPEMUL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]INSTALL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]JOBCTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]LADRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]LCDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]LIDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]LOGINOUT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]LPDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]MASK_IMAGE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]MBXDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]MP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]MSCP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]MTAAACP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]NODRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]NOTICE.TXT;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]OPCCRASH.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]OPCOM.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]PADRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]PAGEFILE.SYS;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]PBDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]PDDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]PUDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]RENAME.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]REPLY.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]REQUEST.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]RMS.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]RMS.STB;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]RUNDET.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]RXDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SCSLOA.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SET.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SETP0.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SHOW.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SHUTDOWN.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SMGMAPTRM.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]STACONFIG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]STARTUP.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]STARTUP.INS;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SWAPFILE.SYS;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYS.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSBOOT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSGEN.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSINIT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA410.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA41A.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA41D.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA41W.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA650.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA65D.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA65W.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA730.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA750.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA780.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA790.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA8NN.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOA8SS.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOAUV1.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOAUV2.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOAWS1.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOAWS2.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSLOAWSD.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSUAF.DAT;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]SYSUAF.RL2;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TERMTABLE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TFDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TMDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TPU.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TSDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TTDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TUDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TVDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]TYPE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]VAXEMUL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]VAXVMSSYS.PAR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]VMB.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]VMOUNT.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]VMSHELP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XADRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XDDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XEDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XFDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XGDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XMDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XQDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]XWDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]YCDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]YEDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]YFDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSEXE]YIDRIVER.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSHLP.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSHLP]EXAMPLES.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSLIB.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]ADARTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]BASRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]BASRTL2.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]CDDSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]COBRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]CRFSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]DCLTABLES.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]DCXSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]DISMNTSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]DTKSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]EDTSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]ENCRYPSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]FORRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]IMGDMP.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]LBRSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]LIBRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]LIBRTL2.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]MOUNTSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]MTHRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]PASRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]PLIRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]RPGRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]SCNRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]SCRSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]SECURESHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]SMGSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]SUMSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]TPU$CCTSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]TPUSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]TRACE.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]UISSHR.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]UVMTHRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]VAXCRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]VAXCRTLG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSLIB]VMSRTL.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSMAINT.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSMGR.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]SECAUDIT.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]SYCONFIG.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]SYENVIRON.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]SYSHUTDWN.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]SYSTARTUP.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]VMSIMAGES.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMGR]VMSIMAGES.DAT;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSMSG.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]ADAMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]CLIUTLMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]DBGTBKMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]FILMNTMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]NETWRKMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]PASMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]PLIMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]PRGDEVMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]RPGMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]SCNMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]SHRIMGMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]SYSMGTMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]SYSMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]TPUMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSMSG]VAXCMSG.EXE;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSTEST.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0]SYSUPD.DIR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]BLISSREQ.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]CVTLICENSE.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]DECNET.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]DEVELOP.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]EXAMPLES.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]FILETOOLS.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]HELP.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]LIBRARY.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]MANAGER.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]MASK_IMAGE.CLD;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]MISCTOOLS.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]QUEUES.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]REQUIRED.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]SETDEFBOO.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]TEXTTOOLS.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]UETP.TLR;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]VMSINSTAL.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]VMSINSTAL.FDL;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]VMSTAILOR.COM;1 %BACKUP-S-CREATED, created DUA0:[SYS0.SYSUPD]VMSUPDATE.COM;1 %BACKUP-S-CREATED, created DUA0:[000000]SYSEXE.DIR;1 %BACKUP-S-CREATED, created DUA0:[000000]VOLSET.SYS;1 %BACKUP-I-STARTVERIFY, starting verification pass %BACKUP-S-COMPARED, compared DUA0:[000000]000000.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[000000]BACKUP.SYS;1 %BACKUP-S-COMPARED, compared DUA0:[000000]CONTIN.SYS;1 %BACKUP-S-COMPARED, compared DUA0:[000000]CORIMG.SYS;1 %BACKUP-S-COMPARED, compared DUA0:[000000]SYS0.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]MOM$SYSTEM.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSCBI.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSERR.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSERR]ERRSNAP.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSEXE.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]BACKUP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]BADBLOCK.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CLUSTRLOA.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CNDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CONFIGURE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CONINTERR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]COPY.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CRDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CREATE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CSP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CVDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]CWDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DBDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DCL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DDDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DELETE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DIRECTORY.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DISMOUNT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DLDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DMDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DQDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DRDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DUDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DVDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DXDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DYDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]DZDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]ERRFMT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]ERRSNAP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]ESDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]ETDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]F11BXQP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]FILESERV.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]FPEMUL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]INSTALL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]JOBCTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]LADRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]LCDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]LIDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]LOGINOUT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]LPDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]MASK_IMAGE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]MBXDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]MP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]MSCP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]MTAAACP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]NODRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]NOTICE.TXT;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]OPCCRASH.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]OPCOM.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]PADRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]PAGEFILE.SYS;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]PBDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]PDDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]PUDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]RENAME.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]REPLY.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]REQUEST.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]RMS.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]RMS.STB;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]RUNDET.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]RXDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SCSLOA.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SET.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SETP0.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SHOW.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SHUTDOWN.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SMGMAPTRM.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]STACONFIG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]STARTUP.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]STARTUP.INS;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SWAPFILE.SYS;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYS.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSBOOT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSGEN.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSINIT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA410.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA41A.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA41D.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA41W.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA650.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA65D.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA65W.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA730.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA750.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA780.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA790.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA8NN.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOA8SS.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOAUV1.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOAUV2.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOAWS1.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOAWS2.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSLOAWSD.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSUAF.DAT;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]SYSUAF.RL2;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TERMTABLE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TFDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TMDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TPU.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TSDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TTDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TUDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TVDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]TYPE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]VAXEMUL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]VAXVMSSYS.PAR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]VMB.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]VMOUNT.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]VMSHELP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XADRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XDDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XEDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XFDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XGDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XMDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XQDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]XWDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]YCDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]YEDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]YFDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSEXE]YIDRIVER.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSHLP.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSHLP]EXAMPLES.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSLIB.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]ADARTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]BASRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]BASRTL2.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]CDDSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]COBRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]CRFSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]DCLTABLES.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]DCXSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]DISMNTSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]DTKSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]EDTSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]ENCRYPSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]FORRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]IMGDMP.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]LBRSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]LIBRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]LIBRTL2.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]MOUNTSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]MTHRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]PASRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]PLIRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]RPGRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]SCNRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]SCRSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]SECURESHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]SMGSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]SUMSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]TPU$CCTSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]TPUSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]TRACE.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]UISSHR.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]UVMTHRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]VAXCRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]VAXCRTLG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSLIB]VMSRTL.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSMAINT.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSMGR.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]SECAUDIT.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]SYCONFIG.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]SYENVIRON.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]SYSHUTDWN.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]SYSTARTUP.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]VMSIMAGES.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMGR]VMSIMAGES.DAT;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSMSG.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]ADAMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]CLIUTLMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]DBGTBKMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]FILMNTMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]NETWRKMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]PASMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]PLIMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]PRGDEVMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]RPGMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]SCNMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]SHRIMGMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]SYSMGTMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]SYSMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]TPUMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSMSG]VAXCMSG.EXE;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSTEST.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0]SYSUPD.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]BLISSREQ.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]CVTLICENSE.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]DECNET.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]DEVELOP.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]EXAMPLES.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]FILETOOLS.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]HELP.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]LIBRARY.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]MANAGER.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]MASK_IMAGE.CLD;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]MISCTOOLS.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]QUEUES.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]REQUIRED.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]SETDEFBOO.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]TEXTTOOLS.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]UETP.TLR;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]VMSINSTAL.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]VMSINSTAL.FDL;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]VMSTAILOR.COM;1 %BACKUP-S-COMPARED, compared DUA0:[SYS0.SYSUPD]VMSUPDATE.COM;1 %BACKUP-S-COMPARED, compared DUA0:[000000]SYSEXE.DIR;1 %BACKUP-S-COMPARED, compared DUA0:[000000]VOLSET.SYS;1 %BACKUP-I-PROCDONE, Operation completed. Processing finished at 21-JUL-2022 14:37:38.49 If you do not want to perform another standalone BACKUP operation, use the console to halt the system. If you do want to perform another standalone BACKUP operation, ensure the standalone application volume is online and ready. Enter "YES" to continue: [STRG + e] Simulation stopped, PC: 80008B1F (BRB 80008B1F) sim> EXIT Goodbye
Finish Installation and Configure System
sim> ATT TQ0 BB-BT05D-BE_VMS4.6_87.tap
sim> BOOT
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> B DUA0
2..1..0..
VAX/VMS Version KG 15-Jun-1987 10:00
Please enter the date and time (DD-MMM-YYYY HH:MM): 21-jul-2022 14:43
Enter drive holding distribution kit (DDCU): MUA0:
%MOUNT-I-MOUNTED, VMS046 mounted on _MUA0:
If this node is part of a cluster, you may want to set up
your system disk to run multiple cluster nodes from a single disk.
Do you want to know more about cluster system disks [N]? Y
In a cluster, you can run multiple systems with up to 14 nodes sharing
all files except PAGEFILE.SYS, SWAPFILE.SYS, SYSDUMP.DMP and VAXVMSSYS.PAR.
Do you want to generate a cluster common system disk [N]? Y
In order to successfully boot the system, you must provide a nonzero value
for the SYSGEN parameter SCSSYSTEMID and a nonblank value for the SYSGEN
parameter SCSNODE. See the Guide to VAXclusters for information on
setting up other SYSGEN parameters after the system is installed.
Enter this node's SCSSYSTEMID value: 1025
Enter this node's SCSNODE name: EARL
Restoring library saveset.
%BACKUP-I-STARTVERIFY, starting verification pass
Restoring optional saveset.
%BACKUP-I-STARTVERIFY, starting verification pass
Creating [V4COMMON] directory tree.
%DCL-I-SUPERSEDE, previous value of SYS$COMMON has been superseded
%DCL-I-SUPERSEDE, previous value of SYS$SYSROOT has been superseded
%DCL-I-SUPERSEDE, previous value of SYS$COMMON has been superseded
Now we will ask you for new passwords for the following accounts:
SYSTEM, SYSTEST, FIELD
Enter new password for account SYSTEM: vms047 (not echoed)
Re-enter the password for account SYSTEM for verification: vms047 (not echoed)
%UAF-I-MDFYMSG, user record(s) updated
Enter new password for account SYSTEST: vms047 (not echoed)
Re-enter the password for account SYSTEST for verification: vms047 (not echoed)
%UAF-I-MDFYMSG, user record(s) updated
Enter new password for account FIELD: vms047 (not echoed)
Re-enter the password for account FIELD for verification: vms047 (not echoed)
%UAF-I-MDFYMSG, user record(s) updated
Creating RIGHTS database file, SYS$SYSTEM:RIGHTSLIST.DAT
Ignore any "%SYSTEM-F-DUPIDENT, duplicate identifier" errors.
%UAF-I-RDBCREMSG, RIGHTSLIST.DAT created
%UAF-I-RDBADDMSGU, identifier DEFAULT value: [000200,000200] added to RIGHTSLIST.DAT
%UAF-I-RDBADDMSGU, identifier FIELD value: [000001,000010] added to RIGHTSLIST.DAT
%UAF-I-RDBADDMSGU, identifier SYSTEM value: [000001,000004] added to RIGHTSLIST.DAT
%UAF-I-RDBADDMSGU, identifier SYSTEST value: [000001,000007] added to RIGHTSLIST.DAT
%UAF-E-RDBADDERRU, unable to add SYSTEST_CLIG value: [000001,000007] to RIGHTSLIST.DAT
-SYSTEM-F-DUPIDENT, duplicate identifier
%UAF-I-NOMODS, no modifications made to system authorization file
%UAF-I-RDBDONEMSG, rights database modified
AUTOGEN computes the SYSGEN parameters for your configuration
and then reboots the system with the new parameters.
After the reboot, you may want to do one or more of the following tasks
(consult the Guide to VAX/VMS System Manager's Reference Manual for
detailed information):
- Delete SYS$SYSTEM:STARTUP.INS
- DECOMPRESS THE SYSTEM LIBRARIES - For space considerations, many of the system
libraries are shipped in a data compressed format. If you have enough disk
space, you may decompress them for faster access. Use SYS$UPDATE:LIBDECOMP.COM
to data expand the libraries. If you choose not to decompress these libraries
there will be a negative impact on the performance of the HELP and LINK
commands.
- APPLY THE MANDATORY UPDATE - The mandatory update for VMS V4.6 must be applied
as soon as possible. You will be unable to install any optional software
products until this update has been applied.
Running AUTOGEN -- Please wait.
%AUTOGEN-I-BEGIN, GETDATA phase is beginning.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:PARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GETDATA phase has successfully completed.
%AUTOGEN-I-BEGIN, GENPARAMS phase is beginning.
%AUTOGEN-I-NEWFILE, A new version of SYS$MANAGER:VMSIMAGES.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:SETPARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GENPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, GENFILES phase is beginning.
%AUTOGEN-I-CREATE, DISK$VAXVMSRL4:[SYS0.SYSEXE]PAGEFILE.SYS
will be modified to hold 13200 blocks.
%SYSGEN-I-EXTENDED, DISK$VAXVMSRL4:[SYS0.SYSEXE]PAGEFILE.SYS;1 extended
%AUTOGEN-I-CREATE, DISK$VAXVMSRL4:[SYS0.SYSEXE]SWAPFILE.SYS
will be modified to hold 8400 blocks.
%SYSGEN-I-EXTENDED, DISK$VAXVMSRL4:[SYS0.SYSEXE]SWAPFILE.SYS;1 extended
%AUTOGEN-I-DUMPFILE, A 32772 block dump file will be created.
%SYSGEN-I-CREATED, SYS$SYSROOT:[SYSEXE]SYSDUMP.DMP;1 created
%AUTOGEN-I-END, GENFILES phase has successfully completed.
%AUTOGEN-I-BEGIN, SETPARAMS phase is beginning.
%AUTOGEN-I-END, SETPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, REBOOT phase is beginning.
The system is shutting down to allow the system to boot with the
generated site-specific parameters and installed images.
The system will automatically reboot after the shutdown and the
upgrade will be complete.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 0
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message from user SYSTEM at Batch 14:46:25
The system will shut down in 0 minutes; back up soon. Please log off.
Reboot system with AUTOGENerated parameters
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
Loading system software.
?06 HLT INST
PC = 20050419
?15 CORRPTN
Apply Mandatory Update
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> [STRG + e]
Simulation stopped, PC: 20040CD1 (TSTB R1)
sim> ATT TQ0 BB-KY83C-BE_VMS4.6-MUP_87.tap
sim> C
>>> B DUA0
2..1..0..
VAX/VMS Version KG 15-Jun-1987 10:00
The MicroVMS system is now executing the system startup procedure.
%UAF-I-RDBADDMSG, identifier SYS$NODE_EARL value: %X80010000 added to RIGHTSLIST.DAT
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 21-JUL-2022 14:47:48.52
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version KG
$ @SYS$UPDATE:VMSINSTAL * MUA0:
VAX/VMS Software Product Installation Procedure KG
It is 21-JUL-2022 at 14:48.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
Please mount the first volume of the set on MUA0:.
* Are you ready? YES
%MOUNT-I-MOUNTED, MUP046 mounted on _EARL$MUA0:
The following products will be processed:
VMSMUP V4.6
Beginning installation of VMSMUP V4.6 at 14:48
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
This kit contains the mandatory update for Version 4.6 of VAX/VMS.
It must be applied to the 4.6 base kit.
1) Apply all fixes to the system
2) Create a file with the descriptions of all fixes
3) Both of the above
* What would you like to do [3]: 3
%VMSMUP-I-FIXDESC, The fixes are described in SYS$UPDATE:VMSMUP046.TXT
* Do you want to purge files replaced by this installation [YES]? YES
%MOUNT-I-MOUNTED, MUP046 mounted on _EARL$MUA0:
%BACKUP-I-STARTVERIFY, starting verification pass
%BACKUP-W-NOFILES, no files selected from MUA0:[000000]VMSMUP046.B;
%DELETE-W-SEARCHFAIL, error searching for SYS$COMMON:[SYSUPD.KITINSTAL_SCRATCH]*.*;*
-RMS-E-DNF, directory not found
-SYSTEM-W-NOSUCHFILE, no such file
%BACKUP-I-STARTVERIFY, starting verification pass
%BACKUP-W-NOFILES, no files selected from MUA0:[000000]VMSMUP046.C;
1) CTDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]CTDRIVER.EXE;1
2) F11BXQP (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]F11BXQP.EXE;2
3) LATSYM (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]LATSYM.EXE;2
4) PEDRIVER (miscellaneous fix)
5) RMS (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]RMS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]RMS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]RMS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]RMS.EXE;1
6) SYS (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]SYS.EXE;1
7) SYSLOA8NN (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]SYSLOA8NN.EXE;1
8) TUDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]TUDRIVER.EXE;1
9) UETINIT00 (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]UETINIT00.EXE;1
10) VAXCRTL (miscellaneous fix)
11) VAXCRTL (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]VAXCRTL.EXE;1
12) VAXCRTLG (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]VAXCRTLG.EXE;1
13) XQDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMSMUP046]XQDRIVER.EXE;1
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of VMSMUP V4.6 completed at 14:48
%VMSINSTAL-I-REBOOT, This product requires that the system be rebooted.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message on EARL from user SYSTEM at _EARL$OPA0: 14:48:47
EARL will shut down in 0 minutes; back up soon. Please log off node EARL.
Reboot after VMSMUP V4.6 installation.
1 terminal has been notified on EARL.
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
SYSTEM SHUTDOWN COMPLETE - USE CONSOLE TO HALT SYSTEM
Infinite loop, PC: 80008D7E (BRB 80008D7E)
sim> EXIT
Goodbye
Install Local Area VAXcluster Key
sim> ATT TQ0 AQ-JK26A-BE LOCAL AREA VAXCLUSTER 1.0 86.tap
sim> BOOT
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> B DUA0
2..1..0..
VAX/VMS Version V4.6 6-Jul-1987 17:00
The MicroVMS system is now executing the system startup procedure.
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 21-JUL-2022 14:50:26.03
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.6
Last interactive login on Thursday, 21-JUL-2022 14:47
$ @SYS$UPDATE:VMSINSTAL * MUA0:
VAX/VMS Software Product Installation Procedure V4.6
It is 21-JUL-2022 at 14:50.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
Please mount the first volume of the set on MUA0:.
* Are you ready? YES
%MOUNT-I-MOUNTED, LAV mounted on _EARL$MUA0:
The following products will be processed:
LAV V1.0
Beginning installation of LAV V1.0 at 14:51
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of LAV V1.0 completed at 14:51
VMSINSTAL procedure done at 14:51
Cluster Configuration
Configure Cluster Boot Node
$ @SYS$MANAGER:BOOT_CONFIG
Boot Node Configuration Procedure
This procedure can CONFIGURE a Local Area VAXcluster boot node
or ADD another system disk.
CONFIGURE a boot node or ADD another system disk [CONFIGURE]? CONFIGURE
This procedure configures a boot node in a cluster. It initializes
the cluster authorization file, sets the volume label of SYS$SYSDEVICE
to EARL_SYS, modifies SYS$SYSTEM:MODPARAMS.DAT, invokes AUTOGEN,
and reboots the system with the new parameters.
To ensure that you have the required privileges, invoke this
procedure from the system manager's account.
WARNING - The cluster PASSWORD will not be echoed.
Enter this cluster's group number: 1
Enter this cluster's password: SECRET (not echoed)
Re-enter this cluster's password for verification: SECRET (not echoed)
Enter this node's SCSSYSTEMID value: 1025
Enter this node's DECnet node name: EARL
How many boot nodes will be in this cluster (1 or 2)? 1
AUTOGEN computes the SYSGEN parameters for your configuration
and then reboots the system with the new parameters.
After the reboot, you may want to configure other nodes in
your cluster.
Running AUTOGEN -- Please wait.
%AUTOGEN-I-BEGIN, GETDATA phase is beginning.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:PARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GETDATA phase has successfully completed.
%AUTOGEN-I-BEGIN, GENPARAMS phase is beginning.
%AUTOGEN-I-OVERRIDE, user specified value for VAXCLUSTER
overrides preceding requirements for this parameter in PARAMS.DAT
%AUTOGEN-I-NEWFILE, A new version of SYS$MANAGER:VMSIMAGES.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:SETPARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GENPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, GENFILES phase is beginning.
%AUTOGEN-I-NOCHANGE, No page file modifications will be made.
%AUTOGEN-I-NOCHANGE, No swap file modifications will be made.
%AUTOGEN-I-NOCHANGE, No dump file modifications will be made.
%AUTOGEN-I-END, GENFILES phase has successfully completed.
%AUTOGEN-I-BEGIN, SETPARAMS phase is beginning.
%AUTOGEN-I-END, SETPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, REBOOT phase is beginning.
The system is shutting down to allow the system to boot with the
generated site-specific parameters and installed images.
The system will automatically reboot after the shutdown and the
upgrade will be complete.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message on EARL from user SYSTEM at _EARL$OPA0: 14:52:02
EARL will shut down in 0 minutes; back up soon. Please log off node EARL.
Reboot system with AUTOGENerated parameters
1 terminal has been notified on EARL.
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
Loading system software.
?06 HLT INST
PC = 20050419
?15 CORRPTN
Install DECnet Routing Key
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> [STRG + e]
Simulation stopped, PC: 20040CD1 (TSTB R1)
sim> ATT RQ1 netrtg040.RX5
sim> C
>>> B DUA0
2..1..0..
VAX/VMS Version V4.6 6-Jul-1987 17:00
waiting to form or join VAXcluster
%STACONFIG-I-LOADSECDB, loading the Local Area VAXcluster security database
%STACONFIG-I-CLUSDEV, starting Local Area VAXcluster protocol on _XQA0:
%STACONFIG-I-LOADMSCP, loading the MSCP disk server
%STACONFIG-I-SERVDEV, now serving device _EARL$DUA0:
%STACONFIG-I-SERVDEV, now serving device _EARL$DUA1:
%CNXMAN, Proposing formation of a VAXcluster
%CNXMAN, Now a VAXcluster member -- system EARL
%CNXMAN, Completing VAXcluster state transition
%%%%%%%%%%% OPCOM 21-JUL-2022 14:54:20.54 %%%%%%%%%%%
Logfile has been initialized by operator _EARL$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;1
%%%%%%%%%%% OPCOM 21-JUL-2022 14:54:20.54 %%%%%%%%%%%
14:54:18.28 Node EARL (csid 00000000) proposed formation of a VAXcluster
%%%%%%%%%%% OPCOM 21-JUL-2022 14:54:20.54 %%%%%%%%%%%
14:54:18.28 Node EARL (csid 00010001) is now a VAXcluster member
%%%%%%%%%%% OPCOM 21-JUL-2022 14:54:20.54 %%%%%%%%%%%
14:54:18.29 Node EARL (csid 00010001) completed VAXcluster state transition
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 21-JUL-2022 14:54:20.69
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.6
Last interactive login on Thursday, 21-JUL-2022 14:50
$ @SYS$UPDATE:VMSINSTAL * DUA1:
VAX/VMS Software Product Installation Procedure V4.6
It is 21-JUL-2022 at 14:55.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
Please mount the first volume of the set on DUA1:.
* Are you ready? YES
%MOUNT-I-MOUNTED, NETRTG01 mounted on _EARL$DUA1:
The following products will be processed:
NETRTG V4.0
Beginning installation of NETRTG V4.0 at 14:55
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
DECnet-VAX Full Function Key installation
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.NETRTG040]NETACP.EXE;1
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of NETRTG V4.0 completed at 14:55
VMSINSTAL procedure done at 14:55
$
Configure DECnet
$ @SYS$MANAGER:NETCONFIG
DECnet-VAX network configuration procedure
This procedure will help you define the parameters needed to get DECnet
running on this machine. You will be shown the changes before they are
executed, in case you wish to perform them manually.
What do you want your DECnet node name to be? [EARL]: EARL
What do you want your DECnet address to be? [1.1]: 1.1
Do you want to operate as a router? [NO (nonrouting)]: YES
Do you want a default DECnet account? [YES]: YES
Here are the commands necessary to setup your system.
--------------------------------------------------------------------------
$ RUN SYS$SYSTEM:NCP
PURGE KNOWN OBJECTS ALL
PURGE MODULE CONFIGURATOR KNOWN CIRCUITS ALL
$ DEFINE/USER SYS$OUTPUT NL:
$ DEFINE/USER SYS$ERROR NL:
$ RUN SYS$SYSTEM:NCP ! Remove existing entry, if any
PURGE NODE 1.1 ALL
PURGE NODE EARL ALL
$ RUN SYS$SYSTEM:NCP
DEFINE EXECUTOR ADDRESS 1.1 STATE ON
DEFINE EXECUTOR NAME EARL
DEFINE EXECUTOR MAXIMUM ADDRESS 1023
DEFINE EXECUTOR TYPE ROUTING IV
DEFINE EXECUTOR NONPRIVILEGED USER DECNET
DEFINE EXECUTOR NONPRIVILEGED PASSWORD DECNET
$ DEFINE/USER_MODE SYSUAF SYS$SYSTEM:SYSUAF.DAT
$ RUN SYS$SYSTEM:AUTHORIZE
ADD DECNET /OWNER="DECNET DEFAULT" -
/PASSWORD=DECNET -
/UIC=[376,376] /ACCOUNT=DECNET -
/DEVICE=SYS$SPECIFIC: /DIRECTORY=[DECNET] -
/PRIVILEGE=(TMPMBX,NETMBX) -
/DEFPRIVILEGE=(TMPMBX,NETMBX) -
Press RETURN to continue
/FLAGS=(CAPTIVE) /LGICMD=NL: -
/NOBATCH /NOINTERACTIVE
$ CREATE/DIRECTORY SYS$SPECIFIC:[DECNET] /OWNER=[376,376]
$ RUN SYS$SYSTEM:NCP
DEFINE LINE QNA-0 STATE ON
DEFINE CIRCUIT QNA-0 STATE ON COST 4
DEFINE LOGGING MONITOR STATE ON
DEFINE LOGGING MONITOR EVENTS 0.0-9
DEFINE LOGGING MONITOR EVENTS 2.0-1
DEFINE LOGGING MONITOR EVENTS 4.2-13,15-16,18-19
DEFINE LOGGING MONITOR EVENTS 5.0-18
DEFINE LOGGING MONITOR EVENTS 128.0-4
--------------------------------------------------------------------------
Do you want to go ahead and do it? [YES]: YES
%UAF-I-ADDMSG, user record successfully added
%UAF-I-RDBADDMSGU, identifier DECNET value: [000376,000376] added to RIGHTSLIST.DAT
%UAF-I-DONEMSG, system authorization file modified
%UAF-I-RDBDONEMSG, rights database modified
%NCP-I-NMLRSP, listener response - Success
Logging sink type = monitor
%NML-I-RECADDED, Database entry added
The changes have been made.
If you have not already installed the DECnet-VAX license, then do so now.
After the license has been installed, you should invoke the procedure
SYS$MANAGER:STARTNET.COM to startup DECnet-VAX with these changes.
(If the license is already installed) Do you want DECnet started? [YES]: YES
%%%%%%%%%%% OPCOM 21-JUL-2022 14:56:19.93 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet starting
%RUN-S-PROC_ID, identification of created process is 2020002D
%RUN-S-PROC_ID, identification of created process is 2020002F
$
%%%%%%%%%%% OPCOM 21-JUL-2022 14:56:25.05 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.10, circuit up
From node 1.1 (EARL), 21-JUL-2022 14:56:20.11
Circuit QNA-0
$
%%%%%%%%%%% OPCOM 21-JUL-2022 14:56:30.60 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.7, circuit down, circuit fault
From node 1.1 (EARL), 21-JUL-2022 14:56:30.60
Circuit QNA-0, Line synchronization lost
%%%%%%%%%%% OPCOM 21-JUL-2022 14:56:30.60 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.10, circuit up
From node 1.1 (EARL), 21-JUL-2022 14:56:30.60
Circuit QNA-0
Configure Cluster Satellite Node TRICK
$ @SATELLITE_CONFIG
Satellite Configuration Procedure
This procedure configures a satellite node in the cluster.
It can ADD or REMOVE a satellite node, and it can MODIFY
the network database.
To ensure that you have the required privileges, invoke this
procedure from the system manager's account.
If the local disk on the satellite node is to be INITIALIZED for
paging and swapping, please be sure you are satisfied with the
BACKUP of the local disk before proceeding.
ADD, REMOVE or MODIFY a satellite node [ADD]? ADD
Verifying circuits in network database...
May this procedure temporarily interrupt DECnet traffic [YES]? YES
What is the device name for the new system root [SYS$SYSDEVICE:]? SYS$SYSDEVICE:
What is the name of the new system root [SYS1]? SYS6
What is the DECnet node name of the satellite node? TRICK
What is the DECnet node address of the satellite node? 1.6
Allow conversational bootstraps on the satellite node [NO]? NO
Creating directory tree SYS6...
%CREATE-I-CREATED, EARL$DUA0:<SYS6> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSEXE> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSLIB> created
%SET-I-ENTERED, EARL$DUA0:<000000>V4COMMON.DIR;1 entered as EARL$DUA0:<SYS6>SYSCOMMON.DIR;
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSTEST> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSMAINT> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSMGR> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSHLP> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSHLP.EXAMPLES> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSUPD> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSMSG> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSERR> created
%CREATE-I-CREATED, EARL$DUA0:<SYS6.SYSCBI> created
System root SYS6 created.
What is the hardware address of the satellite node? 08-00-2B-0C-15-21
Updating network database...
Size of pagefile for the new satellite [10000 blocks]? 10000
Size of swap file for the new satellite [8000 blocks]? 8000
May the local satellite disk be used for paging and swapping? NO
%SYSGEN-I-CREATED, EARL$DUA0:<SYS6.SYSEXE>PAGEFILE.SYS;1 created
%SYSGEN-I-CREATED, EARL$DUA0:<SYS6.SYSEXE>SWAPFILE.SYS;1 created
The satellite configuration procedure has successfully completed.
This node has been configured to allow the satellite node to
join this cluster.
The first time the satellite node boots, "NETCONFIG" and
"AUTOGEN" will run automatically.
$
Cluster Testing VMS V4.6
microvax2000.ini for the Satellite Node (a Diskless MicroVAX 2000)
; microvax2000.ini SET QUIET SET CPU MODEL=MICROVAX SET CPU 8M SET CPU CONHALT SET CPU IDLE=VMS ATT NVR NVR-VS2000.BIN SET CONSOLE LOG=TRICK_001.LOG SET RD0 DIS SET RD1 DIS SET RD2 DIS SET RD3 DIS SET RZ1 DIS SET RZ2 DIS SET RZ3 DIS SET RZ4 DIS SET RZ5 DIS SET RZ6 DIS SET RZ7 DIS SET XS ENA set NAR MAC=08-00-2B-0C-15-21 ATT XS tap:tap2 BOOT
Boot of Cluster Satellite TRICK MicroVAX 2000
Ensure that the Boot Node EARL and the Satellite Node TRICK are connected via Ethernet.
I use this setup.
KA410-A V2.3
F_..E...D...C?..B...A...9...8...7...6...5...4_..3_..2_..1...
?? C 0080 0000.0004
? 6 00A0 0000.4001
>>> B ESA0
-ESA0
System loaded by node EARL (AA-00-04-00-01-04)
VAX/VMS Version V4.7 28-Oct-1987 13:00
%CNXMAN, Discovered system EARL
%CNXMAN, Established connection to system EARL
%STACONFIG-I-LOADMSCP, loading the MSCP disk server
waiting to form or join VAXcluster
%CNXMAN, Sending VAXcluster membership request to system EARL
%CNXMAN, Now a VAXcluster member -- system TRICK
Configuring network...
%UAF-E-UAEERR, invalid username, username already exists
%UAF-I-NOMODS, no modifications made to system authorization file
%UAF-I-RDBNOMODS, no modifications made to rights database
%NCP-I-NMLRSP, listener response - Success
Logging sink type = monitor
%NML-I-RECADDED, Database entry added
%AUTOGEN-I-BEGIN, GETDATA phase is beginning.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:PARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GETDATA phase has successfully completed.
%AUTOGEN-I-BEGIN, GENPARAMS phase is beginning.
%AUTOGEN-I-NEWFILE, A new version of SYS$MANAGER:VMSIMAGES.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:SETPARAMS.DAT has been created.
You may wish to purge this file.
%AUTOGEN-I-END, GENPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, GENFILES phase is beginning.
%AUTOGEN-I-NOCHANGE, No page file modifications will be made.
%AUTOGEN-I-NOCHANGE, No swap file modifications will be made.
%AUTOGEN-I-DUMPFILE, A 12292 block dump file will be created.
%SYSGEN-I-CREATED, SYS$SYSROOT:[SYSEXE]SYSDUMP.DMP;1 created
%AUTOGEN-I-END, GENFILES phase has successfully completed.
%AUTOGEN-I-BEGIN, SETPARAMS phase is beginning.
%AUTOGEN-I-END, SETPARAMS phase has successfully completed.
%AUTOGEN-I-BEGIN, REBOOT phase is beginning.
The system is shutting down to allow the system to boot with the
generated site-specific parameters and installed images.
The system will automatically reboot after the shutdown and the
upgrade will be complete.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 0
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%SYSTEM-F-DEVOFFLINE, device is not in configuration or not available
%OPCOM-W-NOREMBROAD, no VAXcluster terminals were notified because OPCOM is not available
SHUTDOWN message on TRICK from user SYSTEM at TRICK Batch 12:07:55
TRICK will shut down in 0 minutes; back up soon. Please log off node TRICK.
Reboot system with AUTOGENerated parameters
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
83 BOOT SYS
-ESA0
System loaded by node EARL (AA-00-04-00-01-04)
VAX/VMS Version V4.7 28-Oct-1987 13:00
%CNXMAN, Discovered system EARL
%CNXMAN, Established connection to system EARL
waiting to form or join VAXcluster
%CNXMAN, Sending VAXcluster membership request to system EARL
%CNXMAN, Now a VAXcluster member -- system TRICK
%%%%%%%%%%% OPCOM 26-JUL-2022 12:09:56.42 %%%%%%%%%%%
Logfile has been initialized by operator _TRICK$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;1
%%%%%%%%%%% OPCOM 26-JUL-2022 12:09:56.74 %%%%%%%%%%%
12:09:38.71 Node TRICK (csid 00010004) is now a VAXcluster member
%%%%%%%%%%% OPCOM 26-JUL-2022 12:09:56.81 %%%%%%%%%%%
Operator _EARL$OPA0: has been enabled, username SYSTEM
%RUN-S-PROC_ID, identification of created process is 2080002C
%%%%%%%%%%% OPCOM 26-JUL-2022 12:10:04.31 %%%%%%%%%%%
Message from user DECNET on TRICK
DECnet starting
%%%%%%%%%%% OPCOM 26-JUL-2022 12:10:08.27 %%%%%%%%%%% (from node EARL at 26-JUL-2022 12:10:08.13)
Message from user DECNET on EARL
DECnet event 4.15, adjacency up
From node 1.1 (EARL), 26-JUL-2022 12:10:08.13
Circuit QNA-0, Adjacent node = 1.6 (TRICK)
%RUN-S-PROC_ID, identification of created process is 2080002E
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 26-JUL-2022 12:10:11.66
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.7 on node TRICK
Last interactive login on Tuesday, 26-JUL-2022 11:59
Last non-interactive login on Sunday, 24-JUL-2022 19:23
$ SHOW NET
VAX/VMS Network status for local node 1.6 TRICK on 26-JUL-2022 12:10:42.97
This is a nonrouting node, and does not have any network information.
The designated router for TRICK is node 1.1 .
$ @SYS$SYSTEM:SHUTDOWN
SHUTDOWN -- Perform an Orderly System Shutdown
How many minutes until final shutdown [0]: [Enter]
Reason for shutdown [Standalone]: [Enter]
Do you want to spin down the disk volumes [NO]? [Enter]
Do you want to invoke the site-specific shutdown procedure [YES]? [Enter]
Should an automatic system reboot be performed [NO]? [Enter]
When will the system be rebooted [later]: [Enter]
Shutdown options (enter as a comma-separated list):
REMOVE_NODE Remaining nodes in the cluster should adjust quorum
CLUSTER_SHUTDOWN Entire cluster is shutting down
REBOOT_CHECK Check existence of basic system files
Shutdown options [NONE]: [Enter]
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%%%%%%%%%%% OPCOM 26-JUL-2022 12:11:13.78 %%%%%%%%%%%
Operator status for operator _TRICK$OPA0:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10, OPER11,
OPER12
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-SHUTNET, The DECnet network will now be shut down.
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
%%%%%%%%%%% OPCOM 26-JUL-2022 12:11:15.12 %%%%%%%%%%%
Message from user DECNET on TRICK
DECnet shutting down
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
SHUTDOWN message on TRICK from user SYSTEM at _TRICK$OPA0: 12:11:15
TRICK will shut down in 0 minutes; back up later. Please log off node TRICK.
Standalone
1 terminal has been notified on TRICK.
1 terminal has been notified on EARL.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
%%%%%%%%%%% OPCOM 26-JUL-2022 12:11:18.10 %%%%%%%%%%%
Message from user SYSTEM on TRICK
_TRICK$OPA0:, TRICK shutdown was requested by the operator.
%%%%%%%%%%% OPCOM 26-JUL-2022 12:11:18.35 %%%%%%%%%%%
Logfile was closed by operator _TRICK$OPA0:
Logfile was SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;1
%%%%%%%%%%% OPCOM 26-JUL-2022 12:11:18.42 %%%%%%%%%%%
Operator _TRICK$OPA0: has been disabled, username SYSTEM
SYSTEM SHUTDOWN COMPLETE - USE CONSOLE TO HALT SYSTEM
Infinite loop, PC: 80008D7E (BRB 80008D7E)
sim> exit
Goodbye
Boot of Cluster Satellite TRICK (seen from Boot Node)
$ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:20.61 %%%%%%%%%%% Message from user DECNET on EARL DECnet event 0.3, automatic line service From node 1.1 (EARL), 21-JUL-2022 16:10:19.52 Circuit QNA-0, Load, Requested, Node = 1.6 (TRICK) File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21 $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:25.61 %%%%%%%%%%% Message from user DECNET on EARL DECnet event 0.3, automatic line service From node 1.1 (EARL), 21-JUL-2022 16:10:24.14 Circuit QNA-0, Load, Successful, Node = 1.6 (TRICK) File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21 $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK $ %CNXMAN, Discovered system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:29.21 %%%%%%%%%%% 16:10:29.21 Node EARL (sysid 1025) discovered node TRICK (sysid 1030) $ %CNXMAN, Established connection to system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:29.22 %%%%%%%%%%% 16:10:29.22 Node EARL (csid 00010001) established connection to node TRICK $ %CNXMAN, Received VAXcluster membership request from system TRICK %CNXMAN, Proposing addition of system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:39.21 %%%%%%%%%%% 16:10:39.21 Node EARL (csid 00010001) received VAXcluster membership request from node TRICK %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:39.21 %%%%%%%%%%% 16:10:39.21 Node EARL (csid 00010001) proposed addition of node TRICK $ %CNXMAN, Completing VAXcluster state transition $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:10:39.88 %%%%%%%%%%% 16:10:39.88 Node EARL (csid 00010001) completed VAXcluster state transition $ SHOW CLUSTER View of Cluster from system ID 1025 node: EARL 21-JUL-2022 16:11:24 +-------------------+---------+ | SYSTEMS | MEMBERS | +--------+----------+---------+ | NODE | SOFTWARE | STATUS | +--------+----------+---------+ | EARL | VMS V4.6 | MEMBER | | TRICK | VMS V4.6 | MEMBER | +--------+----------+---------+ $ %CNXMAN, Lost connection to system TRICK %CNXMAN, Timed-out lost connection to system TRICK %CNXMAN, Proposing reconfiguration of the VAXcluster %CNXMAN, Removed from VAXcluster system TRICK %CNXMAN, Completing VAXcluster state transition $
Cluster Satellite TRICK Reboot (seen from Boot Node)
SHUTDOWN message on EARL from user SYSTEM at _TRICK$OPA0: 16:18:01 TRICK will shut down in 0 minutes; back up later. Please log off node TRICK. Standalone $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:04.50 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:18:04.30) Message from user SYSTEM on TRICK _TRICK$OPA0:, TRICK shutdown was requested by the operator. $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:04.77 %%%%%%%%%%% Operator _TRICK$OPA0: has been disabled, username SYSTEM $ %CNXMAN, Lost connection to system TRICK %CNXMAN, Timed-out lost connection to system TRICK %CNXMAN, Proposing reconfiguration of the VAXcluster %CNXMAN, Removed from VAXcluster system TRICK %CNXMAN, Completing VAXcluster state transition $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:14.93 %%%%%%%%%%% 16:18:14.93 Node EARL (csid 00010001) lost connection to node TRICK %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:14.94 %%%%%%%%%%% 16:18:14.93 Node EARL (csid 00010001) timed-out lost connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:14.94 %%%%%%%%%%% 16:18:14.93 Node EARL (csid 00010001) proposed reconfiguration of the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:14.94 %%%%%%%%%%% 16:18:14.93 Node TRICK (csid 00010003) has been removed from the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:18:14.94 %%%%%%%%%%% 16:18:14.93 Node EARL (csid 00010001) completed VAXcluster state transition $ %CNXMAN, Deleting CSB for system TRICK %CNXMAN, Discovered system TRICK
Upgrade to VMS V4.7
Install Main Upgrade
$ [STRG + e] Simulation stopped, PC: 80008B1F (BRB 80008B1F) sim> ATT TQ0 BB-KY59A-BE_VMS_4.7.tap sim> C $ MC NCP NCP>SET EXEC STATE OFF
NCP>EXIT
%%%%%%%%%%% OPCOM 21-JUL-2022 16:20:12.60 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 0.7, aborted service request
From node 1.1 (EARL), 21-JUL-2022 16:20:12.60
Circuit QNA-0, Receive error
%%%%%%%%%%% OPCOM 21-JUL-2022 16:20:17.65 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 2.0, local node state change
From node 1.1 (EARL), 21-JUL-2022 16:20:17.08
Operator command, Old state = On, New state = Off
%%%%%%%%%%% OPCOM 21-JUL-2022 16:20:17.65 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.7, circuit down, circuit fault
From node 1.1 (EARL), 21-JUL-2022 16:20:17.08
Circuit QNA-0, Line synchronization lost
%%%%%%%%%%% OPCOM 21-JUL-2022 16:20:17.93 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet shutting down
$ @SYS$UPDATE:VMSINSTAL VMS047
VAX/VMS Software Product Installation Procedure V4.6
It is 21-JUL-2022 at 16:20.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
* Where will the distribution volumes be mounted: MUA0:
Please mount the first volume of the set on MUA0:.
* Are you ready? YES
%MOUNT-I-MOUNTED, VMS047 mounted on _EARL$MUA0:
The following products will be processed:
VMS V4.7
Beginning installation of VMS V4.7 at 16:23
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
This kit contains Version 4.7 of VAX/VMS. It must be installed
upon Version 4.6 of VAX/VMS.
NOTE: Among the new images shipped in this kit are
PEDRIVER.MSKEXE and DSDRIVER.MSKEXE. If your
system is running LAVc or volume shadowing
software, you MUST reapply the LAVC or volume
shadowing key(s) AFTER applying the Version 4.7
update. If you do not reapply the appropriate keys,
your system will not be running the updated
images.
The first phase of the upgrade will attempt to verify that all Digital
supplied accounts are secured against obvious penetration attempts.
%UPGRADE-I-PWD_OKAY, account password for SYSTEM verified
%UPGRADE-I-PWD_OKAY, account password for FIELD verified
%UPGRADE-I-PWD_OKAY, account password for SYSTEST verified
%UPGRADE-W-PWD_INVALID, account password for SYSTEST_CLIG is invalid
-UPGRADE-I-PWD_WEAK, password is too easy to guess
Because of the preceding error, you must take action to secure this account.
You must either disable this account, change its password, or do both.
* Do you want to disable the account [YES]? YES
%UPGRADE-I-DISUSER, account SYSTEST_CLIG disabled
* Do you want to change the account password [YES]? YES
You must now select a new primary password for the SYSTEST_CLIG account. The
password you select must be at least 8 characters in length and may not
be the same as the name of the account.
New password: vms04747 (not echoed)
Verification: vms04747 (not echoed)
%UAF-I-MDFYMSG, user record(s) updated
%UPGRADE-I-PWD_SET, primary password for account SYSTEST_CLIG set
%UPGRADE-I-NONEXIST, account USER does not exist
%UPGRADE-I-NONEXIST, account USERP does not exist
1) Apply all fixes to the system
2) Create a file with the descriptions of all fixes
3) Both of the above
* What would you like to do [3]: 3
%VMS-I-FIXDESC, The fixes are described in SYS$UPDATE:VMS047.TXT
* Do you want to purge files replaced by this installation [YES]? YES
%MOUNT-I-MOUNTED, VMS047 mounted on _EARL$MUA0:
%BACKUP-I-STARTVERIFY, starting verification pass
1) ADARTL (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ADARTL.EXE;1
2) AGEN (miscellaneous fix)
3) AUTOGEN (edit text file)
4) BACKUP (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]BACKUP.EXE;1
5) CLUSTRLOA (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]CLUSTRLOA.EXE;3
6) COBRTL (miscellaneous fix)
7) COBRTL (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]COBRTL.EXE;2
8) CSP (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]CSP.EXE;3
9) CTDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSEXE]CTDRIVER.EXE;2
%VMSINSTAL-W-NOFILE, New file CTDRIVER.EXE does not exist.
10) DEBUG (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]DEBUG.EXE;1
11) DSDRIVER (miscellaneous fix)
12) ERFCTLSHR (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ERFCTLSHR.EXE;1
13) ERFLIB (miscellaneous fix)
%VMS-I-ERFLIB.TLB TA79 update completed successfully,
14) ERFPROC1 (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ERFPROC1.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ERFPROC1.EXE;1
15) ESDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ESDRIVER.EXE;1
16) ETDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]ETDRIVER.EXE;1
17) F11BXQP (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]F11BXQP.EXE;3
18) HSCPAD (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]HSCPAD.EXE;1
19) JOBCTL (new image)
20) LATCP (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LATCP.EXE;2
21) LATSYM (new image)
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LATSYM.EXE;3
22) LTDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]LTDRIVER.EXE;1
23) MOM (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]MOM.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]MOM.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]MOM.EXE;1
24) MONITOR (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]MONITOR.EXE;1
25) MTAAACP (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]MTAAACP.EXE;1
26) NETACP (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETACP.EXE;1
27) NETDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NETDRIVER.EXE;1
28) NODRIVER (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NODRIVER.EXE;3
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]NODRIVER.EXE;3
29) PEDRIVER (miscellaneous fix)
30) RMS (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSEXE]RMS.EXE;2
%PATCH-I-ECOSET, eco level 2 already set in VMI$ROOT:[SYSEXE]RMS.EXE;2
%PATCH-I-ECOSET, eco level 3 already set in VMI$ROOT:[SYSEXE]RMS.EXE;2
%PATCH-I-ECOSET, eco level 4 already set in VMI$ROOT:[SYSEXE]RMS.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]RMS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]RMS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]RMS.EXE;1
31) SATELLITE_CONFIG (edit text file)
32) SECURESHR (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SECURESHR.EXE;1
33) SET (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SET.EXE;1
34) SMBSRVSHR (new image)
35) STABACKUP (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]STABACKUP.EXE;1
36) SYS (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-ECOSET, eco level 80 already set in VMI$ROOT:[SYSEXE]SYS.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
%PATCH-I-ECONOTSET, eco level 88 not set in VMI$ROOT:[SYSEXE]SYS.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYS.EXE;1
37) SYSINIT (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYSINIT.EXE;3
38) SYSLOA790 (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYSLOA790.EXE;3
39) SYSLOA8NN (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSEXE]SYSLOA8NN.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]SYSLOA8NN.EXE;1
40) TPUSHR003 (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TPUSHR.EXE;1
41) TTDRIVER (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TTDRIVER.EXE;3
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TTDRIVER.EXE;3
42) TUDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSEXE]TUDRIVER.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TUDRIVER.EXE;1
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TUDRIVER.EXE;1
43) TVDRIVER (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TVDRIVER.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]TVDRIVER.EXE;2
44) UETDISK00 (new image)
45) UETINIT00 (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSTEST]UETINIT00.EXE;2
%VMSINSTAL-W-NOFILE, New file UETINIT00.EXE does not exist.
46) UETINIT01 (new image)
47) UISSHR (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]UISSHR.EXE;4
48) VAXCRTL (miscellaneous fix)
49) VAXCRTL (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSLIB]VAXCRTL.EXE;2
%VMSINSTAL-W-NOFILE, New file VAXCRTL.EXE does not exist.
50) VAXCRTLG (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSLIB]VAXCRTLG.EXE;2
%VMSINSTAL-W-NOFILE, New file VAXCRTLG.EXE does not exist.
51) VMB (new image)
%VMS-I-VMB, ****************** IMPORTANT ********************
%VMS-I-VMB, A new VMB.EXE was just copied to your system disk.
%VMS-I-VMB, If your VAX processor bootstraps from an HSC disk over the
%VMS-I-VMB, CI, you must update your console device after completing
%VMS-I-VMB, this update procedure. See Section 1.7 of the Version 4.7
%VMS-I-VMB, VMS Release Notes for instructions.
%VMS-I-VMB, ***************************************************
52) VPM (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]VPM.EXE;1
53) XGDRIVER (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]XGDRIVER.EXE;3
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]XGDRIVER.EXE;3
54) XQDRIVER (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-ECOSET, eco level 1 already set in VMI$ROOT:[SYSEXE]XQDRIVER.EXE;2
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]XQDRIVER.EXE;1
55) YFDRIVER (new image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.VMS047]YFDRIVER.EXE;3
%VMS-E-ERRORS, Of the 55 fixes listed above, the following 4 should be reviewed:
9, 45, 49, 50
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of VMS V4.7 completed at 16:24
%VMSINSTAL-I-REBOOT, This product requires that the system be rebooted.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:24:30.63 %%%%%%%%%%%
Operator status for operator _EARL$OPA0:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10, OPER11,
OPER12
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message on EARL from user SYSTEM at _EARL$OPA0: 16:24:30
EARL will shut down in 0 minutes; back up soon. Please log off node EARL.
Reboot after VMS V4.7 installation.
1 terminal has been notified on EARL.
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:24:30.79 %%%%%%%%%%%
Message from user SYSTEM on EARL
_EARL$OPA0:, EARL shutdown was requested by the operator.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:24:30.80 %%%%%%%%%%%
Logfile was closed by operator _EARL$OPA0:
Logfile was SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;1
%%%%%%%%%%% OPCOM 21-JUL-2022 16:24:30.81 %%%%%%%%%%%
Operator _EARL$OPA0: has been disabled, username SYSTEM
SYSTEM SHUTDOWN COMPLETE - USE CONSOLE TO HALT SYSTEM
Infinite loop, PC: 80008D7E (BRB 80008D7E)
Boot VMS V4.7 and Re-Install Local Area VAXcluster Key
sim> BOOT
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> b dua0
2..1..0..
VAX/VMS Version V4.7 28-Oct-1987 13:00
%STACONFIG-I-LOADSECDB, loading the Local Area VAXcluster security database
SYSGEN%W-NOMSG, Message number 00000910
PEDRIVER.EXE
%STACONFIG-W-WARNING, unable to locate PEDRIVER, STS = 00000908
waiting to form or join VAXcluster
%CNXMAN, Proposing formation of a VAXcluster
%CNXMAN, Now a VAXcluster member -- system EARL
%CNXMAN, Completing VAXcluster state transition
%%%%%%%%%%% OPCOM 21-JUL-2022 16:28:01.53 %%%%%%%%%%%
Logfile has been initialized by operator _EARL$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;2
%%%%%%%%%%% OPCOM 21-JUL-2022 16:28:01.53 %%%%%%%%%%%
16:27:59.48 Node EARL (csid 00000000) proposed formation of a VAXcluster
%%%%%%%%%%% OPCOM 21-JUL-2022 16:28:01.53 %%%%%%%%%%%
16:27:59.48 Node EARL (csid 00010001) is now a VAXcluster member
%%%%%%%%%%% OPCOM 21-JUL-2022 16:28:01.53 %%%%%%%%%%%
16:27:59.48 Node EARL (csid 00010001) completed VAXcluster state transition
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 21-JUL-2022 16:28:01.68
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.7
Last interactive login on Thursday, 21-JUL-2022 16:14
$ [STRG + e]
Simulation stopped, PC: 80008B1F (BRB 80008B1F)
sim> ATT TQ0 AQ-JK26A-BE LOCAL AREA VAXCLUSTER 1.0 86.tap
sim> C
$ @SYS$UPDATE:VMSINSTAL * MUA0:
VAX/VMS Software Product Installation Procedure V4.7
It is 21-JUL-2022 at 16:28.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
Please mount the first volume of the set on MUA0:.
* Are you ready? YES
%MOUNT-I-MOUNTED, LAV mounted on _EARL$MUA0:
The following products will be processed:
LAV V1.0
Beginning installation of LAV V1.0 at 16:29
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of LAV V1.0 completed at 16:29
VMSINSTAL procedure done at 16:29
$
Install VMS V4.7 Security Update
$ [STRG + e]
Simulation stopped, PC: 80008B1F (BRB 80008B1F)
sim> ATT TQ0 BB-MI46A-BE_VMS_V47SECUPD030.tap
sim> C
$ @SYS$UPDATE:VMSINSTAL * MUA0:
VAX/VMS Software Product Installation Procedure V4.7
It is 21-JUL-2022 at 16:29.
Enter a question mark (?) at any time for help.
* Are you satisfied with the backup of your system disk [YES]? YES
Please mount the first volume of the set on MUA0:.
* Are you ready? YES
%MOUNT-I-MOUNTED, V47SEC mounted on _EARL$MUA0:
The following products will be processed:
V47SECUPD V3.0
V50SECUPD V3.0
Beginning installation of V47SECUPD V3.0 at 16:29
%VMSINSTAL-I-RESTORE, Restoring product saveset A...
Mandatory security update kit
1) Apply all fixes to the system
2) Create a file with the descriptions of all fixes
3) Both of the above
* What would you like to do [3]: 3
%V47SECUPD-I-FIXDESC, The fixes are described in SYS$UPDATE:V47SECUPD030.TXT
* Do you want to purge files replaced by this installation [YES]? YES
%MOUNT-I-MOUNTED, V47SEC mounted on _EARL$MUA0:
1) INSTALL (new image)
2) MOUNTSHR (new image)
3) SECURESHR (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.V47SECUPD030]SECURESHR.EXE;1
4) SYS (patch image)
%PATCH-I-NOLCL, image does not contain local symbols
%PATCH-I-NOGBL, some or all global symbols not accessible
%PATCH-I-WRTFIL, updating image file VMI$ROOT:[SYSUPD.V47SECUPD030]SYS.EXE;1
%VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories...
Installation of V47SECUPD V3.0 completed at 16:30
%VMSINSTAL-I-REBOOT, This product requires that the system be rebooted.
%VMSINSTAL-W-PRODSKIP, Products that have not been installed will be skipped.
SHUTDOWN -- Perform an Orderly System Shutdown
%SHUTDOWN-I-BOOTCHECK, Performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, Basic reboot consistency check completed
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:30:07.34 %%%%%%%%%%%
Operator status for operator _EARL$OPA0:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10, OPER11,
OPER12
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message on EARL from user SYSTEM at _EARL$OPA0: 16:30:07
EARL will shut down in 0 minutes; back up soon. Please log off node EARL.
Reboot after V47SECUPD V3.0 installation.
1 terminal has been notified on EARL.
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:30:07.59 %%%%%%%%%%%
Message from user SYSTEM on EARL
_EARL$OPA0:, EARL shutdown was requested by the operator.
%%%%%%%%%%% OPCOM 21-JUL-2022 16:30:07.60 %%%%%%%%%%%
Logfile was closed by operator _EARL$OPA0:
Logfile was SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;2
%%%%%%%%%%% OPCOM 21-JUL-2022 16:30:07.60 %%%%%%%%%%%
Operator _EARL$OPA0: has been disabled, username SYSTEM
SYSTEM SHUTDOWN COMPLETE - USE CONSOLE TO HALT SYSTEM
Infinite loop, PC: 80008D7E (BRB 80008D7E)
sim> EXIT
Goodbye
Boot Boot Node after VMS V4.7 Security Update
sim> BOOT
KA630-A.V1.3
Performing normal system tests.
5..4..3..
Tests completed.
>>> B DUA0
2..1..0..
VAX/VMS Version V4.7 28-Oct-1987 13:00
%STACONFIG-I-LOADSECDB, loading the Local Area VAXcluster security database
waiting to form or join VAXcluster
%STACONFIG-I-CLUSDEV, starting Local Area VAXcluster protocol on _XQA0:
%STACONFIG-I-LOADMSCP, loading the MSCP disk server
%STACONFIG-I-SERVDEV, now serving device _EARL$DUA0:
%STACONFIG-I-SERVDEV, now serving device _EARL$DUA1:
%CNXMAN, Proposing formation of a VAXcluster
%CNXMAN, Now a VAXcluster member -- system EARL
%CNXMAN, Completing VAXcluster state transition
%%%%%%%%%%% OPCOM 21-JUL-2022 16:32:44.41 %%%%%%%%%%%
Logfile has been initialized by operator _EARL$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;3
%%%%%%%%%%% OPCOM 21-JUL-2022 16:32:44.41 %%%%%%%%%%%
16:32:42.46 Node EARL (csid 00000000) proposed formation of a VAXcluster
%%%%%%%%%%% OPCOM 21-JUL-2022 16:32:44.41 %%%%%%%%%%%
16:32:42.46 Node EARL (csid 00010001) is now a VAXcluster member
%%%%%%%%%%% OPCOM 21-JUL-2022 16:32:44.41 %%%%%%%%%%%
16:32:42.47 Node EARL (csid 00010001) completed VAXcluster state transition
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
SYSTEM job terminated at 21-JUL-2022 16:32:44.57
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.7
Last interactive login on Thursday, 21-JUL-2022 16:28
$ @startnet
%%%%%%%%%%% OPCOM 21-JUL-2022 16:34:59.70 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet starting
%RUN-S-PROC_ID, identification of created process is 2020002D
%RUN-S-PROC_ID, identification of created process is 2020002F
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:35:04.84 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.10, circuit up
From node 1.1 (EARL), 21-JUL-2022 16:34:59.90
Circuit QNA-0
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:35:10.85 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 0.7, aborted service request
From node 1.1 (EARL), 21-JUL-2022 16:35:10.85
Circuit QNA-0, Receive error
%%%%%%%%%%% OPCOM 21-JUL-2022 16:36:05.85 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.10, circuit up
From node 1.1 (EARL), 21-JUL-2022 16:36:05.85
Circuit QNA-0
Get rid of the recurring DECnet Event Messages
There's a kind of "bug" in VMS V4.7:
As long as there's no other DECnet computer connected, DECnet is permanently flapping down and up again.
This does not hurt in itself, but the recurring OPCOM messages are distracting and disturbing, so let's switch them off.
Enter the following NCP commands to switch the messages for DECnet Events 0.7 and 4.10 off:
Delete from the volatile DECnet database (current settings):
$ MC NCP CLEAR LOGGING MONITOR EVENTS 0.7 $ MC NCP CLEAR LOGGING MONITOR EVENTS 4.10
Delete from the permanent DECnet database (settings for subsequent boots):
$ MC NCP PURGE LOGGING MONITOR EVENTS 0.7 $ MC NCP PURGE LOGGING MONITOR EVENTS 4.10
All other DECnet event messages remain.
Cluster Testing VMS V4.7
Boot of Cluster Satellite TRICK (seen from Boot Node)
$ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:13.43 %%%%%%%%%%% Message from user DECNET on EARL DECnet event 0.3, automatic line service From node 1.1 (EARL), 21-JUL-2022 16:36:13.42 Circuit QNA-0, Load, Requested, Node = 1.6 (TRICK) File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21 $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:18.42 %%%%%%%%%%% Message from user DECNET on EARL DECnet event 0.3, automatic line service From node 1.1 (EARL), 21-JUL-2022 16:36:16.49 Circuit QNA-0, Load, Successful, Node = 1.6 (TRICK) File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21 $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK $ %CNXMAN, Discovered system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:22.85 %%%%%%%%%%% 16:36:22.85 Node EARL (sysid 1025) discovered node TRICK (sysid 1030) $ %CNXMAN, Established connection to system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:22.87 %%%%%%%%%%% 16:36:22.87 Node EARL (csid 00010001) established connection to node TRICK $ %CNXMAN, Received VAXcluster membership request from system TRICK %CNXMAN, Proposing addition of system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:35.08 %%%%%%%%%%% 16:36:35.08 Node EARL (csid 00010001) received VAXcluster membership request from node TRICK %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:35.08 %%%%%%%%%%% 16:36:35.08 Node EARL (csid 00010001) proposed addition of node TRICK $ %CNXMAN, Completing VAXcluster state transition $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:35.77 %%%%%%%%%%% 16:36:35.77 Node EARL (csid 00010001) completed VAXcluster state transition $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:53.66 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:36:53.71) 16:36:36.42 Node TRICK (csid 00010002) is now a VAXcluster member $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:36:53.78 %%%%%%%%%%% Operator _TRICK$OPA0: has been enabled, username SYSTEM
Shutdown of Satellite Node TRICK (seen from Boot Node)
$ %CNXMAN, Lost connection to system TRICK %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:40:49.74 %%%%%%%%%%% 16:40:49.74 Node EARL (csid 00010001) lost connection to node TRICK $ %CNXMAN, Re-established connection to system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:41:04.30 %%%%%%%%%%% 16:41:04.30 Node EARL (csid 00010001) re-established connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:41:15.07 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:40:51.25) 16:40:40.18 Node TRICK (csid 00010002) lost connection to node EARL $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:41:15.12 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:40:51.27) 16:40:40.49 Node TRICK (csid 00010002) re-established connection to node EARL $ SHUTDOWN message on EARL from user SYSTEM at _TRICK$OPA0: 16:42:34 TRICK will shut down in 0 minutes; back up later. Please log off node TRICK. Standalone $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:36.35 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:42:13.02) Message from user SYSTEM on TRICK _TRICK$OPA0:, TRICK shutdown was requested by the operator. $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:36.81 %%%%%%%%%%% Operator _TRICK$OPA0: has been disabled, username SYSTEM $ %CNXMAN, Lost connection to system TRICK %CNXMAN, Timed-out lost connection to system TRICK %CNXMAN, Proposing reconfiguration of the VAXcluster %CNXMAN, Removed from VAXcluster system TRICK %CNXMAN, Completing VAXcluster state transition $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:46.99 %%%%%%%%%%% 16:42:46.99 Node EARL (csid 00010001) lost connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:46.99 %%%%%%%%%%% 16:42:46.99 Node EARL (csid 00010001) timed-out lost connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:47.07 %%%%%%%%%%% 16:42:46.99 Node EARL (csid 00010001) proposed reconfiguration of the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:47.07 %%%%%%%%%%% 16:42:46.99 Node TRICK (csid 00010002) has been removed from the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:47.07 %%%%%%%%%%% 16:42:46.99 Node EARL (csid 00010001) completed VAXcluster state transition $ %CNXMAN, Deleting CSB for system TRICK %CNXMAN, Discovered system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 16:42:47.49 %%%%%%%%%%% 16:42:47.49 Node EARL (sysid 1025) discovered node TRICK (sysid 1030) $ %CNXMAN, Deleting CSB for system TRICK $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK
Boot of Satellite Node TRICK (seen from Boot Node)
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:46:31.37 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 0.3, automatic line service
From node 1.1 (EARL), 21-JUL-2022 16:46:31.37
Circuit QNA-0, Load, Requested, Node = 1.6 (TRICK)
File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:46:36.37 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 0.3, automatic line service
From node 1.1 (EARL), 21-JUL-2022 16:46:35.17
Circuit QNA-0, Load, Successful, Node = 1.6 (TRICK)
File = EARL$DUA0:<SYS6.>, Operating system, Ethernet address = 08-00-2B-0C-15-21
$
%PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK
$
%CNXMAN, Discovered system TRICK
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:46:41.49 %%%%%%%%%%%
16:46:41.49 Node EARL (sysid 1025) discovered node TRICK (sysid 1030)
$
%CNXMAN, Established connection to system TRICK
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:46:41.50 %%%%%%%%%%%
16:46:41.50 Node EARL (csid 00010001) established connection to node TRICK
$
%CNXMAN, Received VAXcluster membership request from system TRICK
%CNXMAN, Proposing addition of system TRICK
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:47:53.52 %%%%%%%%%%%
16:47:53.52 Node EARL (csid 00010001) received VAXcluster membership request from node TRICK
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:47:53.52 %%%%%%%%%%%
16:47:53.52 Node EARL (csid 00010001) proposed addition of node TRICK
$
%CNXMAN, Completing VAXcluster state transition
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:47:54.21 %%%%%%%%%%%
16:47:54.21 Node EARL (csid 00010001) completed VAXcluster state transition
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:48:11.46 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:48:11.53)
16:48:06.13 Node TRICK (csid 00010003) is now a VAXcluster member
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:48:11.58 %%%%%%%%%%%
Operator _TRICK$OPA0: has been enabled, username SYSTEM
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:50:48.90 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:50:48.97)
Message from user DECNET on TRICK
DECnet starting
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:50:52.75 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet event 4.15, adjacency up
From node 1.1 (EARL), 21-JUL-2022 16:50:52.75
Circuit QNA-0, Adjacent node = 1.6 (TRICK)
$
%%%%%%%%%%% OPCOM 21-JUL-2022 16:50:55.91 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 16:50:56.03)
Message from user DECNET on TRICK
DECnet event 4.15, adjacency up
From node 1.6 (TRICK), 21-JUL-2022 16:50:55.81
Circuit SVA-0, Adjacent node = 1.1
$ SHOW NET
VAX/VMS Network status for local node 1.1 EARL on 21-JUL-2022 16:51:08.09
Node Links Cost Hops Next Hop to Node
1.1 EARL 0 0 0 (Local) -> 1.1 EARL
1.6 TRICK 0 4 1 QNA-0 -> 1.6 TRICK
Total of 2 nodes.
$ SET HOST TRICK
Username: SYSTEM
Password: vms047 (not echoed)
Welcome to VAX/VMS version V4.7 on node TRICK
Last interactive login on Thursday, 21-JUL-2022 16:49
$ LOGOUT
SYSTEM logged out at 21-JUL-2022 16:51:39.45
%REM-S-END, control returned to node _EARL::
$
Shutdown of Satellite Node TRICK (seen from Boot Node)
SHUTDOWN message on EARL from user SYSTEM at _TRICK$OPA0: 17:44:47 TRICK will shut down in 0 minutes; back up later. Please log off node TRICK. Standalone $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:44:47.89 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 17:44:47.86) Message from user DECNET on TRICK DECnet shutting down $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:44:50.60 %%%%%%%%%%% (from node TRICK at 21-JUL-2022 17:44:50.60) Message from user SYSTEM on TRICK _TRICK$OPA0:, TRICK shutdown was requested by the operator. $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:44:50.90 %%%%%%%%%%% Operator _TRICK$OPA0: has been disabled, username SYSTEM $ %CNXMAN, Lost connection to system TRICK %CNXMAN, Timed-out lost connection to system TRICK %CNXMAN, Proposing reconfiguration of the VAXcluster %CNXMAN, Removed from VAXcluster system TRICK %CNXMAN, Completing VAXcluster state transition $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.13 %%%%%%%%%%% 17:45:00.13 Node EARL (csid 00010001) lost connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.13 %%%%%%%%%%% 17:45:00.13 Node EARL (csid 00010001) timed-out lost connection to node TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.13 %%%%%%%%%%% 17:45:00.13 Node EARL (csid 00010001) proposed reconfiguration of the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.15 %%%%%%%%%%% 17:45:00.13 Node TRICK (csid 00010003) has been removed from the VAXcluster $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.15 %%%%%%%%%%% 17:45:00.13 Node EARL (csid 00010001) completed VAXcluster state transition $ %CNXMAN, Deleting CSB for system TRICK %CNXMAN, Discovered system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:00.64 %%%%%%%%%%% 17:45:00.64 Node EARL (sysid 1025) discovered node TRICK (sysid 1030) $ %CNXMAN, Deleting CSB for system TRICK $ %%%%%%%%%%% OPCOM 21-JUL-2022 17:45:22.70 %%%%%%%%%%% Message from user DECNET on EARL DECnet event 4.18, adjacency down From node 1.1 (EARL), 21-JUL-2022 17:45:22.70 Circuit QNA-0, Adjacent node listener receive timeout Adjacent node = 1.6 (TRICK) $ %PEA0, Software is Closing Virtual Circuit - REMOTE NODE TRICK
Shutdown Boot Node EARL
$ @SYS$SYSTEM:SHUTDOWN
SHUTDOWN -- Perform an Orderly System Shutdown
How many minutes until final shutdown [0]: [Return]
Reason for shutdown [Standalone]:
Do you want to spin down the disk volumes [NO]? [Return]
Do you want to invoke the site-specific shutdown procedure [YES]? [Return]
Should an automatic system reboot be performed [NO]? [Return]
When will the system be rebooted [later]: [Return]
Shutdown options (enter as a comma-separated list):
REMOVE_NODE Remaining nodes in the cluster should adjust quorum
CLUSTER_SHUTDOWN Entire cluster is shutting down
REBOOT_CHECK Check existence of basic system files
Shutdown options [NONE]: [Return]
%SHUTDOWN-I-OPERATOR, This terminal is now an operator's console.
%%%%%%%%%%% OPCOM 21-JUL-2022 17:47:04.61 %%%%%%%%%%%
Operator status for operator _EARL$OPA0:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10, OPER11,
OPER12
%SHUTDOWN-I-DISLOGINS, Interactive logins will now be disabled.
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-SHUTNET, The DECnet network will now be shut down.
%SHUTDOWN-I-STOPQUEMAN, The queue manager will now be stopped.
%%%%%%%%%%% OPCOM 21-JUL-2022 17:47:04.70 %%%%%%%%%%%
Message from user DECNET on EARL
DECnet shutting down
%JBC-E-JOBQUEDIS, system job queue manager is not running
SHUTDOWN message on EARL from user SYSTEM at _EARL$OPA0: 17:47:04
EARL will shut down in 0 minutes; back up later. Please log off node EARL.
Standalone
1 terminal has been notified on EARL.
%SHUTDOWN-I-SITESHUT, The site-specific shutdown procedure will now be invoked.
%SHUTDOWN-I-STOPUSER, All user processes will now be stopped.
%SHUTDOWN-I-REMOVE, All installed images will now be removed.
%SHUTDOWN-I-DISMOUNT, All volumes will now be dismounted.
%%%%%%%%%%% OPCOM 21-JUL-2022 17:47:05.08 %%%%%%%%%%%
Message from user SYSTEM on EARL
_EARL$OPA0:, EARL shutdown was requested by the operator.
%%%%%%%%%%% OPCOM 21-JUL-2022 17:47:05.09 %%%%%%%%%%%
Logfile was closed by operator _EARL$OPA0:
Logfile was SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;3
%%%%%%%%%%% OPCOM 21-JUL-2022 17:47:05.11 %%%%%%%%%%%
Operator _EARL$OPA0: has been disabled, username SYSTEM
SYSTEM SHUTDOWN COMPLETE - USE CONSOLE TO HALT SYSTEM
Infinite loop, PC: 80008D7E (BRB 80008D7E)
sim> exit
Goodbye
Log file closed
Recommended Reading
- AA-JP20C-TE VMS Local Area VAXcluster Manual (included in the installation set])
