Difference between revisions of "PDP-10"

From Computer History Wiki
Jump to: navigation, search
m (clean up two different 'NCP'S)
m (→‎External links: +Evolution of the DECsystem 10)
Line 137: Line 137:
 
** [http://www.bitsavers.org/pdf/dec/pdp10/KI10/DECsystem-10_Technical_Summary_1971.pdf DECsystem-10 Technical Summary]
 
** [http://www.bitsavers.org/pdf/dec/pdp10/KI10/DECsystem-10_Technical_Summary_1971.pdf DECsystem-10 Technical Summary]
 
** [http://www.bitsavers.org/pdf/dec/pdp10/KL10/EK-108OU-PD-002_KL10-Based_Physical_Description_Mar77.pdf EK-108OU-PD-002], "KL10-Based Physical Description" - has images of CJ dual card connectors and QuickLatch connectors, pp. 69-70
 
** [http://www.bitsavers.org/pdf/dec/pdp10/KL10/EK-108OU-PD-002_KL10-Based_Physical_Description_Mar77.pdf EK-108OU-PD-002], "KL10-Based Physical Description" - has images of CJ dual card connectors and QuickLatch connectors, pp. 69-70
 +
* [https://gordonbell.azurewebsites.net/CGB%20Files/Evolution%20of%20DECsystem%2010%20ACM%207801%20c.pdf The Evolution of the DECsystem 10] - [[CACM]] paper that covers the evolution from the PDP-6 through the KL10
 
* [https://www.ultimate.com/phil/pdp10/ Phil's PDP10 Miscellany Page] - an incredible collection of stuff
 
* [https://www.ultimate.com/phil/pdp10/ Phil's PDP10 Miscellany Page] - an incredible collection of stuff
 
** [https://www.ultimate.com/phil/pdp10/20yrs/index.html Twenty Years of 36-bit Computing with Digital 1964-1984]
 
** [https://www.ultimate.com/phil/pdp10/20yrs/index.html Twenty Years of 36-bit Computing with Digital 1964-1984]
Line 149: Line 150:
  
 
[[Category: DEC Architectures]]
 
[[Category: DEC Architectures]]
−
[[Category: PDP-10 Systems]]
+
[[Category: PDP-10s]]
 
[[Category: DEC Mainframes]]
 
[[Category: DEC Mainframes]]

Revision as of 22:53, 6 August 2022

A PDP-10 KL10 Model 1090

A series of large, 36-bit word mainframe-like systems built by DEC. They were basically a re-implementation of the earlier PDP-6 architecture, whose hardware engineering had been a failure. (The machines were so similar at the programming level that PDP-6 object code could run on a PDP-10.)

DEC sold 4 different generations of PDP-10 processors: the KA10, the KI10, the KL10, and the small KS10. All except the KS10 were available in multi-processor versions with two CPUs.

PDP-10s were very important machines on the early ARPANET and Internet, being one of the few (relatively!) cheaply available machines which could run a full NCP and later TCP/IP stack as a multi-user environment at the time.

They still have a large following today, due in part to the innovative time-sharing operating systems written for them (especially ITS). There are several good simulators available, notably SIMH and KLH10.

Hardware

Like most mainframes, PDP-10's were composed of a number of separate free-standing units of various types (CPUs, main memory, etc), connected together with busses carried in point-point cables. Systems could be upgraded by adding additional units, or replacing existing units with enhanced successors.

Busses

DEC-10's supported a number of different busses; there are different types of bus for memory and peripherals.

There were three generations of main memory bus, and memory systems to attach to them. The first two were the so-called 'external memory bus', in KA (18-bit address) and KI (22-bit) forms (for the KA10, and KI10 and early KL10, respectively), although they also had protocol differences. The last was the 'internal memory bus', the 'S-Bus' (for the later KL10s, a later version of the S-Bus, the X-Bus, differed only in the logic family it interfaced to). The differences between the two external bus types required a KI10-M Memory Bus Adapter if KA-bit units were to be attached to a KI10. Similarly, KI-type units could be attached to the S-Bus using a DMA20 Memory Bus Adapter.

For peripherals, on the KA10 and KI10 an 'I/O bus' was provided. It allowed peripherals to interrupt the CPU, and supported programmed I/O (including block transfers); speeds of up to 200K transfers/second were possible on the KA10, and 350K transfers/second on the KIl0. The DT01C I/O Bus Switch allowed an device to be switched between two different CPUs. For DMA, mass storage peripherals connected directly to memories (PDP-10 memories are generally multi-port).

On the KL10, an optional DIA20 In/Out Bus Controller could also be attached, to provide a KA10/KI10 compatible I/O bus.

The KS10, which was sui generis, had its own custom memory bus, which appeared only on the main backplane. For I/O, it used the UNIBUS and (via RH11's) the MASSBUS.

Memory bus Quick Latch connector (in latched position)

On the KA10, all the busses were physically instantiated as cables with a pair of dual width PCBs at each end, which plugged into slots in a standard DEC backplane; these later became the CJ connectors. On the KI10 and KL10s with an external memory bus, the memory bus cables ended in a large QuickLatch connector; these connectors were also used on the CPU end of I/O bus cables of those machines.

Devices

In the KA10 and KI10, high-speed mass storage device controllers generally connected to both i) a channel, the DF10 Data Channel, which attached to an external memory bus, and ii) the I/O bus. The CPU controlled the channel via the device controller. This setup was used to connect mass storage controllers, such as:

The RH10 MASSBUS controller (which appeared toward the end of the KI10 period), for MASSBUS mass storage devices, was similarly connected (to a DF10 channel, and the I/O bus). On the KL10, up to 8 RH20 MASSBUS controllers, which similarly supported mass storage devices, could be connected to the system.

KI10/KL10 I/O bus terminator

On machines with an I/O bus, other optional devices (the paper tape reader and punch, and console asynchronous serial line, were standard), which connected to the I/O bus, included:

By the KL10 era, most low-speed peripherals were connected to front end computers, always DEC minicomputers, which allowed the production of PDP-10 specific versions of all those devices to be dispensed with.

Front ends

PDP-10's made use of front end computers from an early stage.

The DA10 Twelve- and Eighteen-Bit Computer Interface, which connected to the I/O bus, allowed a computer such as a PDP-8/I to exchange data with a PDP-10. The DC68A Data Communication System uses a DA10 to communicate with a PDP-8/I which has a DC08 Serial Line Multiplexer to interface with up to 128 asynchronous serial lines.

The DL10, connected to both an external memory bus and the I/O bus, allowed the PDP-10 CPU to control up to four PDP-11's. The DC75 Synchronous Communication Multiplexer uses a DL10 to communicate with a PDP-11/20 which has one or more DS11 Synchronous Line Interfaces to interface with 8 or more (depending on the configuration) synchronous serial lines.

On the KL10, up to 4 DTE20 Ten-Eleven Interface‎‎s, each of which allowed the connection of one PDP-11, could be attached. (One PDP-11, the 'master', a PDP-11/40, would bootstrap the KL10, including loading the microcode; it could also be used for other 'normal' front end activities, such as driving groups of asynchronous serial lines, providing DECtapes, etc.)

Software

The first three generations of PDP-10's were marketed as the DECsystem-10, running the TOPS-10 operating system; the third was also sold as the DECSYSTEM-20, running TOPS-20. (The varying capitalization was allegedly the result of a trademark infringment suit.)

Two other very important operating systems also ran on PDP-10's: MIT's ITS (a very advanced system, from whence came EMACS, and much more besides), and TENEX, which DEC later turned into TOPS-20. WAITS was created at SAIL and also ran at two other sites.

Others

PDP-10 ad

The 36-bit line was cancelled by DEC many times. In the beginning, the PDP-6 was difficult to manufacture and maintain, and only 23 were sold; it was cancelled not long after its introduction. However, it made a comeback as the PDP-10, which was a success. At the end, the PDP-10's uncertain future allowed a number of small vendors to sell PDP-10 'clones'.

Cancelled DEC projects

  • KXF10 "Dolphin", cancelled around 1978.
  • KT20 "Minnow", cancelled around 1979.
  • KC10 "Jupiter", cancelled 1983.
  • KD10

Clones

Two PDP-10 clones were built at Xerox PARC, since that was easier than trying to convince Xerox top management to allow the purchase of a relatively expensive machine from a direct competitor.

Commercial

  • Foonly: F-1, F2, F3, F4, F5 (unfinished)
  • Systems Concepts: SC-30M, SC-40
  • Tymshare: System 26, System 26KL.
  • CompuServe: JRG-1 (unfinished)
  • XKL: TOAD-1, TOAD-2

Hobbyist recreations

Software simulators

See also

Further reading

External links

Retrieved from "https://gunkies.org/w/index.php?title=PDP-10&oldid=27198"