PDP-11/24

The PDP-11/24 was the last low-end UNIBUS PDP-11 system; it used the KDF11-U CPU. Like the earlier PDP-11/44, the -11/24 supported up to 4 Mbytes of main memory, using the Extended UNIBUS between the CPU and memory; all devices were attached to a semi-separate (see below) UNIBUS.

An optional UNIBUS Map board, the KT24, provided a path between the UNIBUS and the EUB for access to all of memory for UNIBUS DMA devices; without it, the UNIBUS address space was statically mapped across to the low 248 Kbytes of EUB main memory, using a cross-connection path on the CPU board. If no KT24 was present, the CPU detected its absence, and turned on a set of drivers on the CPU card which gated the address from the UNIBUS through to the EUB.

System bus structure

As mentioned, the -11/24 used an EUB for the bus between the main memory and the CPU, and the UNIBUS for the bus between the CPU and devices. The two buses were not entirely separated: they shared a set of data lines, but each bus had a separate complete set of address lines.

Either the CPU, or the optional KT24, provided a path for addressing information to flow from the UNIBUS to the EUB, for DMA access to main memory by devices.

The top 256 Kbytes of the CPU's address space were devoted to the UNIBUS; the top 8 Kbytes of that were, as usual, the peripheral page.

Implementation details

The -11/24 used a custom 9-slot backplane (part #5413817); slot 1 was for the CPU, slot 2 could hold either EUB memory or the UNIBUS map; slots 3-6 could hold either EUB memory or UNIBUS SPC devices. Slots 7-8 were ordinary UNIBUS MUD/SPC slots, and slot 9 was an ordinary UNIBUS SPC/UNIBUS Out slot.

The EUB and UNIBUS address lines were kept totally separate in all the slots which supported the EUB (1-6); the 22-bit EUB address bus is carried on the EUB address lines (on connectors A-B), and the 18-bit UNIBUS addresses are carried on the SPC address pins (on connector E). (The lower address lines cannot be shared between the two busses, since the UNIBUS map provides arbitrary mapping from UNIBUS addresses to main memory addresses; so there are no lines which are guaranteed to have the same values, to allow them to be shared between the two busses.)

The data lines were cross-connected between the EUB and SPC/UNIBUS. That is because the DEC EUB memory boards pick up the data lines on connector A, whereas UNIBUS SPC devices must get them on connector C - and the memory/SPC slots of the -11/24 backplane can hold either.

In fact, the CPU board connects to the data bus on the C connector, i.e. the UNIBUS SPC pins. The KT24, contrastingly, uses connector A (the MUD pins) for access to the data bus. The reason for the difference is not known - perhaps board layout issues?

With no KT24, a standard EUB memory can go in slot 2; that slot is special, though (i.e. wired differently from slots 3-6). The KT24 needs not only the UNIBUS lines and EUB address lines (to map from one to the other), it also has some special interconnects with the CPU, (e.g. the 'UNIBUS adapter present' line). Bus grant lines also bypass slot 2; hence the limitation to the KT24 or memory.

Layout

Board locations are:

	Connector
Slot	A	B	C	D	E	F
1	M7133 CPU
2	M7134 UBA or EUB memory
3	EUB memory or SPC device
4	EUB memory or SPC device
5	EUB memory or SPC device
6	EUB memory or SPC device
7	MUD device
8	MUD device
9	UNIBUS Out		SPC

Any slot which can hold a device, but which does not have a device installed in it, must have a grant continuity card such as a G7273 placed in it.

Packaging

The -11/24 came in two different cabinets, the 5-1/4 inch high BA11-L and the 10-1/2 inch BA11-A - the same mounting box as used in the -11/44.

The former is specified to use either the -UA (120VAC input) or -UB (240V) versions of the H777 Power Supply for the -11/24, to provide the 12V needed for the MS11-M EUB memory - although the manual does not mention the use of this memory in the -11/24. The two memories which are mentioned - the MS11-L (which can run on 15V) and MS11-P (which only uses +5V) - should be able to use any H777 variant.

The CPU backplane of the -11/44 uses unique Flexprint cables for power, which go to special connections on bus bars in the BA11-A's power supply, though, not the standard DEC power distribution connectors used by the -11/24 backplane (as in the BA11-L mounting box). So, the -11/24 needs a special 'Power Distribution Board' (part # 54-13815) for the BA11-A, which mounts to the bus bars and provides the needed connectors.

Memory configuration limits

The "PDP-11 UNIBUS Processor Handbook" (1985) says (pg. 4-10) that in the 5.25" box, "only one MS11-P memory module can be configured". The cause/source of that restriction is not given.

It can't be the backplane; i) the 5.25" and 10.5" (for which no limitation is stated) boxes use the same backplane, and ii) the 5.25" box can take more of the smaller MS11-L cards (albeit, again, limited - to three). The backplane does carry all 22 address lines to all EUB slots, and the CPU does drive all 22. So, it's likely that it's a power supply current issue.

The MS11-P only uses +5V, but there's nothing about limiting the number of other (ordinary) boards when an MS11-P is in use. The power supply specs show the BA11-L provides 32A of +5V and 4A of +5VBB; alas, the power consumption specs for the CPU and UNIBUS Map (which is basically necessary, for use of more than 256 Kbytes of memory) boards are not given.

However, the MS11-P uses up to 5A of +5V, and 3A of +5VBB; the MS11-L uses up to 2A of +5V, and 1.3A of +5VBB. The limited amount of +5VBB in the BA11-L does correspond to the limitations on the number of MS11-L and MS11-P boards.