KA11 changes for the KT11-B

The KT11-B Paging Option for the PDP-11/20 involves some modifications to the KA11 CPU. Those changes are documented in a DEC print set, 7605961-0, "Central Processor for KT11-B".

The following prints are included in the "Central Processor for KT11-B" set:

Drawing	Sheets	Title
D-CS-7605961-0-3	3	State Control - M727 K2
D-CS-7605961-0-4	3	Priority - M824 K3
D-CS-7605961-0-5	5	Bus Interface & Instruction Register - M725 K9
D-CS-7605961-0-6	4	Instruction Register Decode - M726 K10
D-CS-7605961-0-7	3	Flag Control - M822 K12
D-CS-7605961-0-8	4	Bus & Console Control - M724 K13
D-BS-7605961-0-9	1	KA11 to KT11 Interface
D-AP-7605961-0-10	1	PC Board Modifications
D-WS-7605961-0-11	1	KA11 Mods for use with KT11-B

KA/KT Interface

The KA11 and KT11-B are connected by a UNIBUS between them (which carries all the CPU's normal bus functions, such as memory cycles), and also by an additional cable. That cable carries various other signals, mostly internal signals of the KA11 which are used by the KT11-B (along with a few additional ones which are synthesized specially), although there are a few signale from the KT11-B, used in the modified KA11.

On the KT11 end, the cable plugs into slot D12, and on the KA11 end, into slot B09. The cable pinout is:

Pin	Source	Signal	! Pin	Source	Signal
A1	-	Ground	A2	-	Unused
B1	KA11	Odd address error	B2	-	Unused
C1	-	Ground	C2	-	Ground
D1	KT11	PGC 04	D2	KA11	RTS
E1	KA11	DEST	E2	KA11	CLKT
F1	-	Ground	F2	-	Ground
H1	KA11	SOURCE	H2	KA11	-TRAPS
J1	KA11	ISR 12	J2	-	Ground
K1	-	Ground	K2	KA11	SERVICE
L1	KA11	ISR 7	L2	-	Ground
M1	KA11	-RTI	M2	KA11	TIME OUT
N1	-	Ground	N2	-	Ground
P1	KA11	JSR	P2	KA11	FETCH
R1	-	Ground	R2	-	Ground
S1	KT11	CLK NPR	S2	KA11	TRAP
T1	-	Ground	T2	KA11	[ST+SR] K13-3
U1	-	Unused	U2	-	Ground
V1	-	Unused	V2	KT11	Force timeout

(Signals partially in lower case are not formal names from the prints, but give a sense of what the signal does.)

KA11 changes

The changes to the KA11 include a small number of modifications to several boards in the KA11 (below), and a number of changes to the wiring of the CPU backplane (also below).

An M138 FLIP CHIP (octal three-input NAND gates) is plugged into the KA11 backplane (in slot B08, otherwise unused), to provide additional gates, which are used to synthesize some of the signals sent across the KA11 - KT11-B interface cable. (Recall that slot B09 is where the interface cable between the KT11-B and KA11 plugs into the KA11.)

Board modifications

Alas, there is only one known set of the prints of the KT11-B changes to the KA11 - and that set is missing the page: "PC Board Modifications", D-AP-7605961-0-10. Luckily, there is apparently just enough duplicate information elsewhere (including a hand-modified set of KA11 prints, showing the changes to support the KT11-B) to allow it to be re-created.

The following are the changes on the three KA11 boards which are modified (KA11 backplane wiring changes are given in other sections below):

On the M824 Priority card, page K3-2:

• The NAND gate (E24) feeding, via another NAND gate (also E24) the NPRF flop (E14) is re-purposed (as a NOR with inverting inputs):
  • Although one input (pin 5) remains connected to pin D12S1, that pin is now connected to K2-3 PERIF REL L
  • The other input (pin 4) is connected to the output of the NOR gate at the top of the page (E18, pin 1)
  • The output (pin 6) is used as an input to the next gate
• A NOR gate is added between that gate, and the clear input of the NPRF flop; the 'KA11 mods' print set shows one gate used for this (E25, a 7402), but the hand-written mods to the standard KA11 prints show a different one (E10, a 7450)
  • In both prints, one input is connected to the output of the previous NAND gate
  • In the 'KA11 mods' print set, the other input is also connected to that signal; in the hand-modified set, that second input is connected to the '1' output of the NPRF flop (E14, pin 5)
  • The output is connected to the clear input of the NPRF flop (E14, pin 1)
• The input of the NAND gate (E24, pin 2) which was being driven by the re-purposed NAND gate is now driven by the same signal as the other input (pin 1)

On the M822 Flag Control card, page K12-2:

• The line in the upper right-hand corner between the output of the NAND gate (E28) and the preset input of the OVFLF flop (E15, pin 1) is deleted

On the M724 Bus & Console Control card, page K13-2:

• The line from the E50 9601 timer low output (pin 6) to the clock input (pin 11) of the E46 Time-out flop is cut
• A spare 7400 NAND gate (in E26), used as an OR with inverting inputs, has its output (pin 8) connected to the flop's clock input; its inputs are:
  • One input (pin 10) is connected to the timer high output (pin 8)
  • The other input (pin 9) is connected to backplane pin F06C1 ('FORCED TIMEOUT')

Wires removed

The following lists of wiring changes on the KA11 backplane give the content from print 7605961-0-11, "KA11 Mods For Use With KT11-B". All wires are listed as being 30 AWG.

Note: This print reproduced poorly, so there may be transcription errors (e.g. '8' for '3', etc). The goal is to eventually cross-check all this information with the prints, to verify all data, and supply that which is currently missing here. '?' indicates a currently un-readable character.

From	To	Signal	Colour
B02T2	F08U2	K13-3 B MSYN H	Orange
D12C2	D12S1	GND 12
E04K1	E07P2	K10-4 CLKT H
E03F1	E04L1	K?-2 SCLK L
D11B1	C06J1	K10-3 ODD ADRS ERR L
C06J1	D02N1	K10-3 ODD ADRS ERR L
D12S1	D12T1	GND 12	Brown

Wires added

All added wires are listed as Orange. This list had previously been checked, and annotated by hand in ink; those annotations are given here. All entries with no annotation given have a hand-written check-mark in ink. Text in italics are comments added during the transcription to this page.

From	To	Signal	Comment
E03F1	F06H1	K1-2 SCLK L
D?2C2	D12T1	GND 12	None
D11B1	D02N1	K10-3 ODD ADDRS ERR L	None
F04P2	B08A1	K10-2 ODD ADDRS ERR L
F04P2	B08B1	K10-2 ODD ADDRS ERR L
F04P2	B08C1	K10-2 ODD ADDRS ERR L
B08D1	B08E1	B08D1
B08D1	B08L1	B08D1
E03F1	B08M1	K1-2 SCLK L	E04L1 - B08M1
B08J1	B08K1	B08J1
B08J1	C06J1	B08J1
B08N1	B09B1	B08N1
E04K1	B08P1	K10-2 CLKT H
E04K1	B08R1	K10-2 CLKT H
E04K1	B08S1	K10-2 CLKT H
B08U1	B08D2	B08U1
B08U1	B08F2	B08U1
B09D1	B08F1	D18 - PGC 04 (1) H
B09D1	B08H1	D18 - PGC 04 (1) H
B09D1	B08F2	D18 - PGC 04 (1) H
B08H2	B08J2	B08H2
B08H2	B0K2	B08H2	(Presumably 'B0K2' is a typo for 'B08K2')
B08H2	B08L2	B08H2
B08H2	E07P2	B08H2
D03T2	B08R2	K1-4 SERVICE H
E03L2	B08N2	K1-3 ISR (3+7) H	None
B08S2	B08T2	B08S2
B08S2	B08U2	B08S2
B08S2	B08V2	B08S2
D11B2	B08P2	K12-3 TRAPS	B02C1 - B08P2
F03J1	B09E1	K1-3 B DEST (0) H
F03M2	B09M2	K1-4 B SOURCE (1) H	B09H1 - F11M2
E03R1	B09J1	K1-3 ISR 12 L
E03K1	B09L1	K1-3 ISR 7 L
F04S2	B09M1	K10-4 RTI H
C04D1	B09P1	K10-2 JSR H
B09S1	F02U2	D18 CLK NPR H
E04R1	B09D2	K10-3 RTS	B09D2 - E11T2
D03P2	B09K2	K1-4 SERVICE L
F06M1	B09M2	K13-3 TIME OUT (0) H
F03J2	B09P2	K1-4 FETCH (0) H
C04P1	B09S2	K10-2 TRAP L
C06V1	B09T2	K13-3 -(ST+SR) H	D06D2 - B11T2
B09V2	F06C1	D18 FORCE TIMEOUT H
B08V1	B09H2	B08V1
F02J1	D06D2	K2-3 CLR PTR L	None
F02P1	D12S1	K2-3 PERIF REL L	None
B12P2	B12V2	DEVICE 2+3 BG06
D11H2	E04L1	K1-2 R/W2 H
B08M2	B09E2	B08M2
F02J1	C06V1	K2-3 CLR PTR L	Unlisted (Not in original table; added by hand)
B09H1	F11M2	K1-3 ISR 12 L