KT11-B Technical Manual

As a Special Systems Option, the KT11-B does not have the usual DEC Technical Manual. This page attempts to provide at least the high-level portions of such a manual.

Note:: The KT11-B theory of operation (either from the page above, or the Option Description manual), must be thoroughly understood before trying to read this page. In particular, register names must be known, as well as the function of high-level internal entities such as the associative memory and the scratchpad memory.

Prints

The Engineering Drawings for the KT11-B (7605071) include the following logic prints:

Number	Page Count	Content
2	2	Address Bus and Control Logic
3	1	State Control Logic
4	1	SP Input Mux
5	2	Associative Memory Control
6	1	Scratch Pad and State Control Logic
7	3	Data Bus and Control Logic
8	1	Keys and Associative Memory
9	1	XP Option for KT11 Associative Memory Control
10	1	PGM Register
11	1	PGC Register
12	1	Timing Logic
13	1	Buffered Signals and Main Logic
14	1	Extended Associative Memory
15	1	KA11 to KT11 Interface
17	1	KT11-B Bus Connectors

The KT11-B is not composed of discrete boards, but rather a large number of mostly small FLIP CHIPs, so the division into drawings, some of which are multi-sheet (as opposed to them all being single-sheet) is a bit arbitrary. It is probably intended to align the drawings with the high-level internal structure.

References to drawing pages are given as 'x-y', where 'x' the drawing number, and 'y' is the individual sheet.

Drawing Conventions

The drawings are somewhat easier to understand if the conventions used in the drawings are understood. Although no document lists them, they can be ascertained by study of the drawings.

Signal Names

Signal names in this drawing set usually start with 'Dxx', where 'xx' is related to the drawing number (given in the table above). (This is similar to the convention in the KA11 drawings, where 'Kxx-y' means that the signal originates on page y of drawing xx.) Note that the 'Dxx' correspondence seems to sometimes be off by one; i.e. a signal tagged 'D04' can be found originating on drawing 05.

In signal names of the form 'XXX (yy)', 'yy' is a bit number (in standard PDP-11 order) in a register or bus. For signals which are provided in both asserted low and asserted high forms, one will see signal names of the form 'XXX (y)', where 'y' is 1 or 0. Note that sometimes these two notations are combined, and one can find signal names of the form 'XXX (yy) (z)'. Inverted (asserted low) signals are also sometimes shown as '-XXX'.

The following specific signal names have the meaning given:

• Signals of the form 'x.y' are states, with 'x' being the major state, and 'y' being the minor state.
• Signal names starting with 'SP' refer to the scratchpad memory, which holds both cache page table entries, as well as some KT11-B registers; SPIN is its input bus, and SPDA is its output bus.
• Signal names starting with 'AM' refer to the associative memory.
• Signal names starting with 'DV' refer to the UNIBUS from the KT11-B to the devices and memory of the system.
• Signal names starting with 'CP' refer to the UNIBUS to the KT11-B from the KA11 CPU.
• Signal names starting with 'PGC' refer to the contents of the Control Status register.
• Signal names starting with 'PGM' refer to the contents of the Maintainence register.

Common Circuits

This circuit (first used in the KA11) is seen in several places in the KT11-B. It is almost always seen as an array of identical circuits, since it provides a 3-input multiplexor with latching capability, and it is used on data paths (usually 16 bits wide).

The latch is cleared by de-asserting the 'Latch' input; data from any of the three inputs (A, B, C) may then be selected for output, and potentially storage, by asserting the matching 'Gate' input. Asserting 'Latch' then stores the current output of the mux.

(Asserting more than one input simultaneously ORs the two inputs together; this capability is used in the KA11, but probably not here.)

States

The KT11-B has a state composed of two parts, the 'X' or major part, and the 'Y' or minor part; the progression of this through the various states is the major control mechanism in the KT11-B.

The X state counter is on print 12; it is composed of a 2-bit counter (allegedly a shift register, but that could not generate 4 discrete states) composed of a pair of D flops, with 4 AND gates with inverting inputs to create individual major state outputs, signals 'XSRx' (x = 0-3).

The Y state counter is an M826 Flip Chip, shown on print 8; its outputs are signals 'YSRx' (x = 0, 1 ,3, 7, 15, 14, 12, 8). (The odd sequence of minor state numbers, and the fact that they are not in numerical order, is confusing, but since that's what's on the prints, that nomenclature has to be used.)

The two groups of signals are combined into signals which indicate that the KT11-B is in that state, for each individual major/minor state, by NAND gates shown on drawing 12; inverters then provide non-inverted forms of each.

There are 4 signals XSHL, XSHR, YSHL, YSHR which control state transitions.

State Table

The following table shows the state transitions:

State	Next State(s)	Comment
0.0	0.8, 1.0	Idle
0.8	0.12	Interrupt, Trap and Start User
0.12	0.14
0.14	0.15
0.15	0.7A
0.7A	0.3A
0.3A	0.1A
0.1A	0.0
0.7B	0.3B	Although the state names are identical to the preceding ones, this is shown on the state diagram as a separate state loop
0.3B	0.1B	Window?
0.1B	1.1
1.0	1.1, 3.0
1.1	1.3
1.3	1.7, 3.3	Exec-per-Process
1.7	0.7B, 1.15
1.15	1.14	Page Violation?
1.14	1.12
1.12	0.12
1.8	1.0
2.0	0.0
2.1	2.0, 2.3	Shared Entry?
2.3	2.7
2.7	2.15
2.15	2.14	Page Violation?
2.14	0.14
2.12	-	State does not exist
2.8	-	State does not exist
3.0	2.0, 3.1, 3.8
3.1	1.1, 2.1, 3.0
3.3	3.1, 3.7A
3.7A	1.7	Although the state name is identical to the preceding ones, this is shown on the state diagram as a separate state loop
3.7B	3.3
3.15	3.7B
3.14	3.15
3.12	3.14
3.8	1.8, 3.12

This table is a transcription of the single-page one in the KT11-B Option Description; that diagram contains a number of labels, but it is not completely clear which states (or transitions) the labels apply to. Over time the hope is to check this table against the multi-page table in that document, and also better described what each state means.

Detailed logic description

This section covers each drawing in more detail, explaining what functions are found in each one.

Address Bus and Control Logic

The first sheet contains buffering between the address lines of the CPU's UNIBUS, and an internal address bus; and also random control logic.

The left side of the second sheet contains an address latching mux (see above), divided into high and low 9-bit halves, which selects between:

• Scratch-pad data output (9 bits wide, repeated in the low and high halves)
• Scratch-pad data input (17 bits wide, although the 17th bit is a synthetic signal, with the low and high halves swapped)
• An internal address bus

The right half of the second sheet contains drivers for the address lines of the KT11-B's output UNIBUS, sourced from the above mux.

State Control Logic

This drawing contains random logic which generates the two major and two minor state change control signals (XSHL, XSHR, YSHL, YSHR).

Scratchpad Input Mux

At the top, a 16-bit wide latching mux (see above) which provides the input to the scratchpad memory. The three inputs are:

• An internal address bus
• An internal data bus
• Scratchpad data output

At the bottom is random logic which generates the selection control signals for the mux.

Associative Memory Control

The first sheet contains a number of different logical units:

• The top right corner contains logic to recognize references to KT11-B internal registers

The second sheet also contains a number of different logical units:

• The right side contains logic to load individual associative memories
• The center bottom contains logic to indicate an associative memory match

Scratchpad and State Control Logic

Random logic which controls the scratchpad memory.

Data Bus and Control Logic

The first sheet contains random control logic.

The left side of the second sheet contains the drivers for data lines of the output UNIBUS, which are fed from the data lines of the input UNIBUS. The right side contains half of a multiplexor (built from NAND gates connected in a wired-OR network) which drives the data lines of the UNIBUS to the CPU; the inputs are:

• The data lines of the output UNIBUS (through a set of receivers, which also generate the internal data bus)
• Scrarchpad data output
• The KT11-B Control and Maintainence registers

The left side of the third sheet contains the other half of the data mux; the right side shows the KW11-L Line Time Clock card.

Keys and Associative Memory

The left-hand side shows the scratchpad memories; the top center shows the associative memories; the top right shows a comparator (use unknown); the bottom right is the counter?/shift register? which generates the minor state. The bottom center is a 3-bit wide latching mux which generates and holds key information.

XP Option for KT11 Associative Memory Control

This contains logic to control the optional cache entries; the left-hand side contains gates to control loading of associative memories, and the right hand side contains logic processing matches.

PGM Register

The KT11-B's Maintenance register: the center top is the replacement counter; the rest of the page is random logic (including S/R flops) to generate the currently undocumented other bits in the Maintenance register - bits 6, 7, 11, 12, 13, 14. (The Option Description indicates - Section 3.3.2.6 - that there are 5 bits, but the drawings show 6.)

PGC Register

The KT11-B's Control and Status register - S/R flops to store the bits, and random logic to control setting and clearing them: in the upper right, the Source and Destination bits; in the center and lower right, the five Violation bits; in the upper left and center, the two Function bits; in the left and center middle, the User and Interrupted User bits, respectively.

Timing Logic

The top and lower right contain gates which combine major and minor state lines into lines for each individual state. The lower left contains the counter (not a shift register, as per the Option Description Section 4.3; it can produce 4 different states from 2 bits, not possible with a shift register) to produce the major state, and logic to produce major state lines.

Buffered Signals and Main Logic

The left side shows the W130 Maintaince Card; the top and right contains buffering for various internal signals.

Extended Associative Memory

The scratchpad memory and associative memories for the optional 16-entry extension (to 24 entries total) for the page table entry cache.

Construction

As mentioned, the KT11-B is constructed out of a large number of smaller Flip Chips, plugged into a custom-wired backplane.

Module Counts

The module type usage counts are:

Type	Function	Count	Comment
M111	16 x Inverters	10	9?
M112	10 x 2-input NOR	5	4? (but there's a '117' could be 112)
M116	6 x 4-input NOR	10
M133	10 x 2-input NAND	24
M135	8 x 3-input NAND	6
M139	3 x 8-input NAND	1
M167	Magnitude comparator	1
M203	8 x R/S flip flops	1
M206	6 x D flip flops	1
M207	6 x J/K flip flops	1
M225	Scratchpad memory	1	2 for 24 cache entries
M240	R/S flip flop	1
M244	6 x quad-2-input-AND/OR gates	6	Used as multiplexor latches (see above)
M259	Associative memory	4	12 for 24 cache entries
M602	2 x Pulse amplifier	1
M611	14 x Power inverter	3
M627	6 x NAND amplifier	7
M721	UNIBUS transceiver	4
M783	12 x UNIBUS NAND transmitters	6
M784	16 x UNIBUS inverter receivers	2
M826	Clock/shift register	1

(The counts are from the list in the "KT11-B Option Description" document; they have been cross-checked against the 'Module Utilization' sheet from the KT11-B Engineering Drawings, and there are still some variances to be sorted out.)

Module Locations

Slot	A	B	C	D
01	UNIBUS In		M259	Mxx
02	M930		M259	M133
03	UNIBUS Out		M259	M133
04	M930		M259
05	M721	M721	M259%
06	M721	M721	M259%
07	M783	M784	M259%
08	M783	M784	M259%	M133
09	M783	M787 $	M259%	M133
10	M783	M244	M259%	M133
11	M783	M244	M259%	M133
12	M783	M244	M259%	M903 @
13	M826	M244	M627	M111
14	W130 $	M244	M627	M133
15	M116	M244	M627	M133
16	M225		M627	M133
17	M225%		M117 X	M133
18	M116	M112	M627	M133
19	M116	M112	M627	M133
20	M116	M112	M627	M133
21	M116	M112		M133
22	M116	M112		M133
23	M116	M602		M133
24	M116	M135		M133
25	M116	M135	M611	M133
26	M116	M135	M611	M133
27	M203	M135	M111	M133
28	M206	M135	M111	M133
29	M207	M135	M611	M133
30	M240	M133	M111	M111
31	M139		M111	M111
32	M167	M111		M111

•  % = Optional
• $ = Not part of KT11-D
• @ = Cable
•  ? = Could be M173

Card Information

The drawings contain a number of different Flip Chips as blocks, without showing individual details; those are given here.

M167

Shown on page 8-1, this is a 8-bit comparator; it compares the value of two 8-bit numbers and provides four outputs which provide the relationships between those two numbers (A=B, A>B, A>=B, and B>=A). (An EQUAL IN input is provided for cascading them, but it is not used here.)

Inputs (bits nummbered in PDP-11 style, with LSB = bit 0):

Input	Pin	Input	Pin
A7	F2	B7	H2
A6	H1	B6	S1
A5	E2	B5	D2
A4	F1	B4	E1
A3	C1	B3	D1
A2	J1	B2	M1
A1	K1	B1	M2
A0	B1	B0	A1

Outputs:

Pin	Signal
P1	EQUAL OUT (L)
R1	EQUAL OUT (H)
V1	A>B (H)
U1	B>=A (H)
L1	A>=B (H)

M203

Shown on pages 7-1, 10-1 and 11-1, although not as as a single block, but rather individual units, this contains R/S flip flops. They are formed from a pair of NAND gates interconnected in the usual fashion; they provide inverted S and R inputs, and normal and inverted outputs.

M225

Shown on pages 8-1 and 14-1, this is a 16x16-bit scratchpad memory; this card is also used in the KA11 processor of the PDP-11/20, and is documented there. In addition to 16-bit wide input and output, and byte write controls, it also provides an 4 sets of the 4 address inputs, and 4 inputs to select the desired set of addresz input. (I.e. the address lines are binary encoded, but the address input select lines are not.) An internal 4-way mux selects the desired set of address inputs.

Data pins:

Input	Pin	Output	Pin
I00	AF2	O00	AE1
I01	AA1	O01	AC1
I02	AK2	O02	AL1
I03	AH1	O03	AJ1
I04	AE2	O04	AF1
I05	AD2	O05	AD1
I06	AJ2	O06	AM1
I07	AH2	O07	AK1
I08	BR2	O08	BM2
I09	BL1	O09	BM1
I10	BV2	O10	BU1
I11	BP1	O11	BR1
I12	BP2	O12	BT2
I13	BN2	O13	BN1
I14	BU2	O14	BV1
I15	BS2	O15	BS1

Control pins:

Address set select	Pin	Address set A	Pin	Address set B	Pin	Address set C	Pin	Address set D	Pin
A0	BE1	AA0	BF2	AB0	BH1	AC0	BE2	AD0	BF1
A1	BJ1	AA1	BD1	AB1	BD2	AC1	BC1	AD1	BA1
A2	AP2	AA2	AV2	AB2	AV1	AC2	AU1	AD2	AU2
A3	AS1	AA3	AT2	AB3	AS2	AC3	AR2	AD3	AR1

Pin BK1 is 'WRITE 15/8', and pin AM2 is 'WRITE 7/0'. In addition, pin AN1 is a control input of some sort, but it is not yet clear what it does.

M240

Shown on pages 10-1 and 11-1, although not as as a single block, but rather individual units, this contains R/S flip flops.

M259

Shown on pages 8-1 and 14-1, this is a dual 8-bit associative memory.

M602

Shown on pages 6-1 and 13-1, although not as as a single block, but rather individual units, this is a dual pulse amplifier. It produces a negative-going pulse (nominally 50 nsec wide), triggered by an input transitioning from high to low; the input is a triple-input OR with inverting inputs.

M787

Shown on page 7-3, this is actually not a part of the KT11-B; rather, it is the KW11-L Line Time Clock, which must reside in the KT11-B's backplane.

M826

Shown on page 8-1, this is a clock with counter?/shift-register?

W180

Shown on page 13-1, this is actually not a part of the KT11-B; rather, it is the Maintenance Card, which must plug into the KT11-B's backplane.