UNIBUS

The UNIBUS (or Unibus - the capitalization style changed over time) was the earliest of two bus technologies used with PDP-11s manufactured by Digital Equipment Corporation; it was first seen in the PDP-11/20, in 1970. Later, early VAX systems from that company used the UNIBUS as an I/O bus.

It was the only bus in most PDP-11 systems, and thus supported several capabilities: the ability of the processor to read and write main memory, and device registers; and the ability for devices to do DMA transfers to memory, and interrupt the CPU.

It could exist on a cable (the original mode of operation), and later, within a backplane (in 'Small Peripheral Controller (SPC)' or 'Modified UNIBUS Device (MUD)' slots). Up to 20 nodes (devices) could be connected to a single UNIBUS segment; additional segments could be connected via a bus repeater.

The UNIBUS contained 16 data lines, and 18 address lines; the 18 address lines allowed the addressing of a maximum of 256 KBytes. Typically, the top 8 KBytes of address space was reserved for the registers of the memory mapped IO devices used in the PDP-11 architecture. (The limit of 18 address lines was to prove a severe handicap in the later phases of the UNIBUS' operational life.)

The bus was completely asynchronous, allowing a mixture of fast and slow devices. It allowed the overlapping of arbitration (selection of the next bus master) while the current bus master was still performing data transfers.

The design deliberately minimized the amount of redundant logic required in the system. For example, a system always contained more slave devices than master devices, so most of the complex logic required to implement asynchronous data transfers was forced into the relatively few master devices. For interrupts, only the interrupt-fielding processor needed to contain the complicated timing logic.

The end result was that most I/O controllers could be implemented with very simple logic; most of the critical logic was later implemented as a custom MSI IC.

Technical details

Two control lines (C0 and C1) allowed the selection of four different data transfer cycle types in normal master/slave cycles:

• DATI (Data In, a read)
• DATIP (Data In/Pause, the first portion of a Read-Modify-Write operation. A DATO or DATOB operation completes this.)
• DATO (Data Out, a word write)
• DATOB (Data Out/Byte, a byte write)

During an interrupt cycle, a fifth style of transfer was used to convey an interrupt vector from the interrupting device to the interrupt-fielding processor.

Lines

The UNIBUS is usually described as containing 56 lines. In its initial BC11A cable instantiation, the UNIBUS was composed of 72 wires (2 standard DEC board edge connectors, with 36 lines per connector); when not counting the power and ground lines, this was reduced to the canonical 56.

Among the UNIBUS signals are:

• BR4-BR7 - Bus (Interrupt) Requests at priorities 4 (lowest) through 7 (highest)
• BG4-BG7 - Bus (Interrupt) Grants at priorities 4 (lowest) through 7 (highest)
• NPR - Non Processor (DMA) Request
• NPG - Non Processor (DMA) Grant
• MSYNC - Master Sync
• SSYNC - Slave Sync
• BBSY - Bus Busy
• SACK - Selection Acknowledge
• PA, PB - Parity control
• C0, C1 - Cycle Control

Cables

For many years, the cable used to carry the UNIBUS from one backplane to another was the BC11A cable, a pair of wide (3-3/4 inch) white flexible printed circuit flat cables, separated by a thin foam layer, with small printed circuit boards with edge connector fingers on each end of the cable. The latter plugged into 'UNIBUS In' and 'UNIBUS out' slots in backplanes. The flat cables actually contained 64 connectors each; every other trace was grounded, to prevent cross-talk between the signal lines.

DEC later developed a series of cards (the M9014, an extended height dual card, and the M9042 short dual card) which plug into the same slots, and contain three 2x20 headers for 40-conductor flat cables (known as H854 cables in DEC parlance); a pair of these, and three cables, perform the same role as a BC11A cable. Both of these cards use the same header pinout, so they may be used interchangeably.

Pinout

The following table gives the pinout for the flat cable form and SPC slot form. Pins are identified in the standard DEC manner; there are two connectors, A and B; pins on the component side are 1, those on the solder side are 2. Pins are identified by the 'DEC alphabet', A-V, with G, I, O and Q dropped.

Signal	Assertion	Termination	Cable Pin	SPC Pin
Initialization and Shutdown
DC LO	L	Slow	BF2	CN1
AC LO	L	Slow	BF1	CV1
INIT	L	Fast	AA1	DL1
Arbitration
NPR	L	Fast	AS2	FJ1
BR7	L	Fast	AT2	DD2
BR6	L	Fast	AU2	DE2
BR5	L	Fast	BC1	DF2
BR4	L	Fast	BD2	DH2
NPG	H	Grant	AU1	In-CA1; Out-CB1
BG7	H	Grant	AV1	In-DK2; Out-DL2
BG6	H	Grant	BA1	In-DM2; Out-DN2
BG5	H	Grant	BB1	In-DP2; Out-DR2
BG4	H	Grant	BE2	In-DS2; Out-DT2
SACK	L	Fast	AR2	FT2
Addressing
A00	L	Fast	BH2	EH2
A01	L	Fast	BH1	EH1
A02	L	Fast	BJ2	EF1
A03	L	Fast	BJ1	EV2
A04	L	Fast	BK2	EU2
A05	L	Fast	BK1	EV1
A06	L	Fast	BL2	EU1
A07	L	Fast	BL1	EP2
A08	L	Fast	BM2	EN2
A09	L	Fast	BM1	ER1
A10	L	Fast	BN2	EP1
A11	L	Fast	BN1	EL1
A12	L	Fast	BP2	EC1
A13	L	Fast	BP1	EK2
A14	L	Fast	BR2	EK1
A15	L	Fast	BR1	ED2
A16	L	Fast	BS2	EE2
A17	L	Fast	BS1	ED1
Data
D00	L	Fast	AC1	CS2
D01	L	Fast	AD2	CR2
D02	L	Fast	AD1	CU2, FE2%
D03	L	Fast	AE2	CT2, FL1%
D04	L	Fast	AE1	CN2, FN2%
D05	L	Fast	AF2	CP2, FF1%
D06	L	Fast	AF1	CV2, FF2%
D07	L	Fast	AH2	CM2, FH1%
D08	L	Fast	AH1	CL2, FK1%
D09	L	Fast	AJ2	CK2
D10	L	Fast	AJ1	CJ2
D11	L	Fast	AK2	CH1
D12	L	Fast	AK1	CH2
D13	L	Fast	AL2	CF2
D14	L	Fast	AL1	CE2
D15	L	Fast	AM2	CD2
Control
C0	L	Fast	BU2	EJ2
C1	L	Fast	BT2	EF2
PA	L	Fast	AM1	CC1
PB	L	Fast	AN2	CS1
BBSY	L	Fast	AP2	FD1
MSYN	L	Fast	BV1	EE1
INTR	L	Fast	AB1	FM1
SSYN	L	Fast	BU1	EJ1, FC1%
Power
Ground	N/A	N/A	AB2
Ground	N/A	N/A	AC2	xC2
Ground	N/A	N/A	AN1
Ground	N/A	N/A	AP1
Ground	N/A	N/A	AR1
Ground	N/A	N/A	AS1
Ground	N/A	N/A	AT1	xT1
Ground	N/A	N/A	AV2
Ground	N/A	N/A	BB2
Ground	N/A	N/A	BC2
Ground	N/A	N/A	BD1
Ground	N/A	N/A	BE1
Ground	N/A	N/A	BT1
Ground	N/A	N/A	BV2
+5	N/A	N/A	AA2	xA2
+5	N/A	N/A	BA2
-15	N/A	N/A	N/A	xB2 (except 1A, 1B, 4A, 4B)

Entries of the form 'xYN' mean that that is available on all 4 connectors (A, B, C and D) in each slot.

% For forward compatibility, use the first pin rather than the second

See also

• Extended UNIBUS
• Small Peripheral Controller
• Modified UNIBUS Device
• QBUS